Mosfet Regulator for Can-Am Outlander 500 570 650 800 850 1000 XT XMR 2010-2018 OEM Repl.# 710001191

 

Battery condition is extremely important. No voltage regulator can work correctly with a bad or weak battery. Always fully charge your battery before performing any charging system tests or replacing parts. If there is any doubt, have the battery load tested or replaced.

There are two possible regulators for the Outlander 1000 2012 and many Outlander Max 500 models. This regulator fits mostly the European / International versions of these models. For the North American versions, the right regulator is part RM30506H. Always check in the 'Fits models' section and please compare to your original part before buying.

With?design

This product is an advanced design that lowers operating temperatures for extended longevity and better performance than the OEM part.

Brand new Mosfet Voltage Regulator Rectifier

STOP BURNING YOUR REGULATOR RECTIFIER !
It is time to update or replace your voltage regulator with the advanced MOSFET type.
It runs cooler than all OEM diode style regulators. In addition, this rectifier has overheat protection, rather than burn up it will simply turn off for a while and cool off.

• Direct replacement to your original unit
• Plug-and-play, direct fit, easy installation
• The quality exceeds the OEM equipment
• Improved heat sink and charging capabilities
• Higher grade of electric components
• All shipped products are tested

We have even included the opposite connector (main harness side) as we know these are often melted / corroded / defective and a major cause of repetitive electrical issues.

 

Can-am Outlander 1000 -- 2012
Can-am Outlander 1000 DPS -- 2013-2016
Can-am Outlander 1000 XT -- 2012-2015
Can-am Outlander 1000 XT-P -- 2013-2015
Can-am Outlander 1000R -- 2016-2018
Can-am Outlander 500 -- 2015
Can-am Outlander 500 DPS -- 2013-2015
Can-am Outlander 500 XT -- 2010-2015
Can-am Outlander 500 XT-P -- 2010
Can-am Outlander 650 DPS -- 2013-2018
Can-am Outlander 650 EFI -- 2017-2018
Can-am Outlander 650 T3 EFI F/C -- 2018
Can-am Outlander 650 XMR -- 2013-2018
Can-am Outlander 650 XT -- 2010-2018
Can-am Outlander 650 XT-P -- 2010-2011
Can-am Outlander 800 R DPS -- 2013-2015
Can-am Outlander 800 R XMR -- 2011-2012, 2015
Can-am Outlander 800 R XT -- 2010-2015
Can-am Outlander 800 R XT-P -- 2010-2011, 2013-2015
Can-am Outlander 800 R XXC -- 2011
Can-am Outlander 850 -- 2016-2017
Can-am Outlander Max 1000 -- 2013-2015
Can-am Outlander Max 1000R -- 2016-2017
Can-am Outlander Max 500 -- 2015
Can-am Outlander Max 500 DPS -- 2013-2015
Can-am Outlander Max 500 LTD -- 2010
Can-am Outlander Max 500 XT -- 2010-2015
Can-am Outlander Max 500 XT-P -- 2010
Can-am Outlander Max 570 -- 2016
Can-am Outlander Max 650 DPS -- 2013-2017
Can-am Outlander Max 650 XT -- 2010-2017
Can-am Outlander Max 650 XT-P -- 2010-2012
Can-am Outlander Max 800 R -- 2013-2015
Can-am Outlander Max 800 R DPS -- 2013-2015
Can-am Outlander Max 800 R LTD -- 2010-2012
Can-am Outlander Max 800 R XT -- 2010-2015
Can-am Outlander Max 800 R XT-P -- 2010-2015
Can-am Outlander Max 850 -- 2016-2017
Can-am Outlander XMR 1000 -- 2013-2016
Can-am Renegade 1000R -- 2016-2017
Can-am Renegade 570 -- 2016-2017
Can-am Renegade 850 -- 2016-2017
Can-am Renegade XXC 1000 -- 2012-2016
Can-am Renegade XXC 800 R -- 2010-2015

 

710001191

 

Please note: There is two different regulator that fits a CAN-AM Renegade 1000 cc 2015. See specification tab for details. PLEASE VALIDATE THESE MEASUREMENTS WITH YOUR OLD REGULATOR BEFORE BUYING THIS PRODUCT

Dimensions :
Width : 120mm
Length : 111mm
Height: 35mm
Fixation holes center to center : 94mm

Other specifications :
Number of plugs : 2
Number of pins : 5

  Before installing your new voltage regulator rectifier;

• Check the AC output of the stator.
• Replace any burned or corroded connectors on stator and regulator/rectifier
• Check and repair any melted wiring.
• Use hi-temp dielectric grease on all connectors.

 

Learn more why and how to repair melted or corroded connectors.