【DE】2.2KW Werkzeugwechsel Frässpindel ISO20 220V ATC Fräsmotor Water Cooled Spindle



Europe countries area:

Austria,Belgium,Bulgaria,CzechRepublic,Denmark,Estonia,Finland,France,Germany,Greece,
Hungary,Ireland,Italy,Latvia,Liechtenstein,Lithuania,Luxembourg,Netherlands,Poland,
Portugal,Romania,Slovakia,Slovenia,Spain,Sweden.  without United Kingdom


Tracking web: (www.dhl.de/en/paket/information/sendungsverfolgung.html) with in one days handling time, When update information on the web,around 3-9 working days arrived


100% Brand New and High Quality

Package include:

  1 x 2.2KW ATC Automatic Tool Change water cooled spindle motor （24000rpm IS020 Holder 220V 5.4A 80mm）

User manual will be by email send you


1. Product overview

1) This spindle is built-in type spindle motor, built-in three asynchronous motors,by theinverter control.As the spindle has a compact structure,high power, big torque, small vibration,low noise characteristics,so it can achieve high speed,high powe cutting,high precision and highstability operation.
2) The bearing of spindle use grease lubricated angular to contact bearings,can beachieved lifelong lubricating within the life cycle.
3) The spindle use forced coolling mode to coolling motor,front and rear bearings.Coolantflow through the reasonable arrangement cycle watercourse of the spindle body,thus can takethe heat generated of the spindle rotation speed, to achieve thermal equilibrium,let spindletemperature within a certain constant value. External cooling device effect:maintaining aconstant temperature of the coolant.
4) The spindle built-in PTC 140 temperature sensor(Technical parameters are visible inother sections of this specification),you can read it anytime if you need to protect the motortemperature.
5) The tool clamping methods:this spindle built-in automatic tool change device,shank form
is ISO20


2. Drawing Size Description



Spindle model

RTM80-20-24Z/2.2 220V

Voltage

220V

Maximum speed

24000rpm

Rated frequency

400Hz

Electric current

5.4A

Motor level

Level 2

Rated power

2.2KW (S1)

Peak power

2.2KW (S6)

Rated torque

0.59Nm

Peak torque

0.84Nm

Technical parameters

Spindle blowing dust/seal gas pressure (MPa)

0.2-0.25

Spindle gas seal gas flow

(L/min)

65±10 (When on Working)

Cooling water pressure (MPa)

>=0.25

Cooling water flow (L/min)

>=2.5

Cooling water temperature deg

24-28

Spindle static state pulse (µm)

<=3

Spindle vibration (mm/s)

<=0.8

Spindle diameter (mm)

dia 80 (0/-0.02)

Motor windings Pressure test (V/M)

1000V/1 minute withstanding Voltage test

Tool Interface

ISO20

Inverter Specifications

2.2KW (220V)

Fitment

For castings, aluminum, glass, etc., and other processing




Spindle installation explanation

1)     Circulating Cooling System Description

The system must ensure that the cooling water temperature of supply spindle is between 24-28deg. Usually setting the flow switch in return pipe of the cooling system,to ensure the supply of spindle cooling water. Cooling water requirements: we recommend using distilled water, while recommend Feinuokesi (Fenix) protective agent F1 (using the scale of 1: 200),coolant temperature is 26deg±2deg,inlet, outlet pipe temperature can’t exceed 5 deg.It is allowed As long as other monitoring can ensure fuller spindle cooling.

2) Air sealing control

In order to prevent water or impurities enters internal of the spindle,spindle will have gas sealing device,the gas seal machine must be started start with the machine at the same time. And the need to go through multi-stage filtration.

3) Compressed gas quality requirements

The quality requirement of gas which is used in gas seals:

Oil content:<0.01mg/m3

Solid particle:<5µ m

Pressure dew point: <7.5deg(0.7MPa)

4) Running-in program instructions

Only all monitoring issued no failures operational signals,at the same time,all safety devices have been installed and working properly,then allow start spindle.

Note: New or spindle which is not used for a long time must to be running slowly.First,start run spindle for half an hour as 25% of the maximum speed,then increase  to 50% of the maximum speed,to run 15 minutes,finally, increase to maximum speed.It’s need to check the temperature of the spindle during the whole process, spindle will get hot, but not hot hand, if the spindle becomes hot, pls stop the operation and contact our customer service department.


ersand

1.) Ihre Bestellung versenden wir innerhalb von 1-2 Werktagen nach Zahlungseingang.

2.) Bitte überprüfen Sie Ihre Adresse, wenn Sie danach bestellen. Wir sind nicht für falsche 
oder unzustellbare Adresse verantwortlich

3.) Wenn die Bestellung am Wochenende erfolgt, dauert es 2 Tage länger



Zahlung

1.) Wir akzeptieren Paypal-Zahlungen, alle Paypal müssen bestätigt werden (Versand- und Rechnungsadresse 
müssen übereinstimmen und korrekt sein und es muss uns Ihre Telefonnummer für die Lieferung mitteilen)

2.) pls abgeschlossen innerhalb von 1-3 Werktagen bezahlt




Rückmeldung


1.) Wir kümmern uns um unsere geschätzten Kunden und werden immer versuchen, Ihnen zu helfen und hoffen, 

ein langes Geschäft mit Ihnen aufzubauen.


2.) Bitte geben Sie uns die Möglichkeit, jedes Problem zu lösen, wir verstehen die Bedenken und Frustrationen, 

die Sie haben könnten, und werden unser Bestes geben, um die Probleme zu lösen.


3.) Bitte kontaktieren Sie uns per eBay-Nachricht oder E-Mail, bevor Sie ein negatives Feedback hinterlassen 

oder Fälle auf der Website öffnen. Wir helfen Ihnen bei der Lösung des Problems.




Erstattung

1.) Defekten oder falschen Artikeln wird ein Ersatz oder eine Rückerstattung angeboten, nachdem die 
Bilder angeboten wurden, um dies zu beweisen.

2.) Wenn Sie das Paket haben und die Ware nicht zufrieden ist oder ein anderes Problem vorliegt, 
teilen Sie uns bitte den Detailgrund mit und geben Sie die Fotos an. Wir helfen Ihnen, alle Probleme zu lösen.













1.8KW water cooled ATC(Automatic Tool Change) Spindle motor ISO20 for engraving
NEW 1.8KW 24000rpm ISO20 Permanent Torque Automatic Tool Changes ATC Spindles
1.8KW ATC Water-Cooled Spindle Motor ISO20 220V 24000rpm for Machining Center
New 1.8KW ATC Water Cooled Spindle Motor Automatic Tool Change ISO20 CNC Machine
New 1.8KW 24000rpm ATC Spindle Motor 220V 5.4A 400Hz ISO20 Water-Cooled 80mm DHL
1.8W ATC Water-Cooled Spindle Motor ISO20 220V 24000rpm fr CNC Machining Center
New 1.8KW 24000rpm ATC Spindle Motor 400Hz 220V 5.4A ISO20 Water-cooled 80mm
1.8KW CNC ATC Water Cooled Spindle Motor ISO20 24000rpm 220V 400Hz for Engraving
New 1.8KW ATC Water Cooled Spindle Motor Automatic Tool Change ISO20 CNC Router
Professional 1.8kW ISO20 220V ATC Spindle Motor Automatic Tool Changer for CNC
1.8KW ATC Spindle Motor Automatic Tool Change Water Cooled 220V 5.4A 24000rpm
1.8KW ATC Water Cooled Spindle Automatic Tool Change Motor ISO20 24000rpm 220V
1.8KW 220V ATC Water Cooled Spindle Automatic Tool Change Motor ISO20 24000rpm
1.8KW 220V ATC Automatic Tool Change Water Cooled Spindle Motor 80mm CNC Milling
1.8KW ISO20 Water Cooled Spindle Automatic Tool Change Motor 220V Engraving ATC
 1.8KW 220V Water Cooled ATC Spindle CNC Router Automatic Tool Change Motor MILL