Series Regulator for Honda SXS 500 / 520 / 700 Pioneer 2019-2023 | OEM# 31600-MKN-D51

KEY FEATURES
 

Brand new aftermarket SERIES voltage regulator rectifier

Direct replacement to your original unit

Plug-and-play, direct fit, easy installation

The quality exceeds the OEM equipment

All products shipped are tested

DESCRIPTION

 

2006 2007 Can-Am Outlander 400 fitment requires a special installation. Refer to the ?Installation? tab at the bottom of this page to see all the details

WHY USE SERIES ENHANCED TECHNOLOGY?


  • Runs much cooler than the Shunt and MOSFET voltage regulator rectifier.
  • Power only flows through the electrical components when the battery is charging.
  • Allows the stator to have lower current flowing when not used, extending its lifetime.
  • The regulator is easier to mount because it?s smaller than the OEM one.

  • With enhanced technology design

    This product is an advanced technology that lowers operating temperatures for extended longevity and better performance than the OEM part.


    THE SERIES VOLTAGE REGULATION TECHNOLOGY

    RMSTATOR?s new SERIES voltage regulator brings better reliability and charging system performance. A SERIES regulator is a significant upgrade over typical shunt type voltage regulators. A shunt regulator controls battery voltage by grounding the stator coils to dissipate current as heat, rather than sending it on to the battery. SERIES regulators control battery voltage by intermittently disconnecting stator coils from the regulator electronics, limiting current flow through the unit and on to the battery completely. This results in lower regulator and stator temperatures, more accurate voltage regulation, and increased reliability of your charging system components.


    Brand new series voltage regulator rectifier

    THE ULTIMATE SOLUTION TO YOUR REGULATOR RECTIFIER PROBLEMS!
    It is time to update or replace your voltage regulator with the advanced series type. It runs cooler than all OEM, Shunt or MOSFET, diode style regulators. In addition, this rectifier has overheat protection, rather than burn up it will simply turn off for a while and cool off.

    • Direct replacement to your original unit
    • Plug-and-play, direct fit, easy installation
    • The quality exceeds the OEM equipment
    • Improved heat sink and charging capabilities
    • Higher grade of electric components
    • All shipped products are tested

    We even include the opposite connector (main harness side) as we know these are often melted / corroded / defective and a major cause for repetitive electrical issues.

    All item pictures are accurate, if in doubt, do not hesitate and compare our item to your original part.

    Vehicle models fitment

     

    Honda SXS 500 Pioneer -- 2021-2022
    Honda SXS 520 Pioneer -- 2021, 2023
    Honda SXS 700 Pioneer -- 2021-2024

    OEM part replacement

     

    4012941
    31600-MKN-D51
    8JP-H1960-10-00
    0824-082
    5JW-81960-00-00
    12317718422
    710000907
    703500717
    61911034000

    Specifications

     

    Dimensions:
    Width: 84 mm
    Length: 90 mm
    Height: 32 mm
    Fixation holes center to center: 69 mm

    Other specifications:
    Number of plugs: 2
    Number of pins: 5
    Minimum Charging Voltage: 14.5 V +- 0.5 V
    Maximum Charging Current: 50 A / 500 W
    Open Circuit Voltage: < 15 V
    Operation Temperature: -20? to 85?

    instructions

     

    Before installing your new Voltage Regulator Rectifier:

    • Check the AC output of the stator
    • Replace any burned or corroded connectors on stator and regulator rectifier
    • Check and repair any melted wiring
    • Use hi-temp dielectric grease on all connectors

    2006 2007 Can-Am Outlander 400 Installation Particularities

    If you are using this regulator for 2006 2007 Can-Am Outlander 400 fitments, it will function perfectly fine. You will need convert your vehicle wiring to our included mating connectors.

    From your original stator connector, the outer 2 Yellow wires will be spliced into 1, the center 2 Yellow wires will be spliced into 1, and the opposite outer 2 Yellow wires will be spliced into 1. These go into our Grey connector in any location, there is no order.

    The Red Battery + goes to the inner terminal of the Black connector. The Brown Battery - (ground) wire goes to the outer terminal of the Black connector. The center terminal of the black connector is not used.

    You will need relocate or build a mounting bracket for this regulator, it will not mount like the original regulator for this application.