This fuel injector cleaner tester can help you diagnose and clean injectors, easily identify common faults such as stuck, blocked, leaked or burnt-out conditions of the fuel injector. Compared with other fuel injector cleaner and tester with only one pair of pulse output teminals(black&red test lead), our fuel injector tester has 2 pulse output teminals(two pairs of test leads), which can test two fuel injectors at the same time for comparison. |
Wide Compatibility This injector cleaner kit is compatible for 12V injectors of almost all vechicle models, for both EFI and GDI injectors.It comes with a large and a small size universal adapters compatible for injectors of most models(except B.MW A.udi),so we newly add 2 adapters to expand its compatibility:a medium size adapter suitable for models such as for VW, for Audi, etc.and another one with threaded hole is exclusively for BMW N series such as N14/N18/N20/N26/N53/N54/N55/N63/S63.(NOTE: Gasoline car only, NOT the diesel engine). |
Mode 0: Standby state, no output Mode 1: Single Pulse Low Power Mode: when the PULSE key is pressed, the fuel injector tester will send out a pulse with a pulse width of about 255 milliseconds. Mode 2: Short Pulse Low Power Mode: the fuel injector tester will send out 50 pulses with a pulse width of about 7 milliseconds. Mode 3: Long Pulse Low Power Mode: the fuel injector cleaner tester will send out 100 pulses, and the pulse width is about 3.5 milliseconds. Mode 4: Continuous Pulse Low Power Mode: the fuel injector tester will output pulses continuously, the pulse rate is about 50 pulses every 1450 milliseconds, and the pulse width is about 7 milliseconds. Mode 5: Single Pulse High Power Mode: the injector tester will send out a pulse with a pulse width of about 255 milliseconds. Mode 6: Short Pulse High Power Mode: the injector tester will send out 50 pulses with a pulse width of about 7 milliseconds. Mode 7: Long Pulse High Power Mode: the injector cleaner tester will send out 100 pulses, and the pulse width is about 3.5 milliseconds. Mode 8: Continuous Pulse High Power Mode: the fuel injector tester will output pulses continuously, the pulse rate is about 50 pulses every 1450 milliseconds, and the pulse width is about 7 milliseconds. Note: During the pulse output period, the MODE SET button is invalid, and the working mode can only be selected by pressing the PULSE button again to terminate the output. |
40inch Power Cord & 20inch Test Lead The length of power cord is up to 40inch/100cm and its test lead is 20 inches,which is more convenient for you to connect and use. The wires are made of superior silica gel, which has better high and low temperature resistance. Fuel injector cleaning kit is powered by 12V battery or an external DC 12V (recommended at least 1.5A) power adapter. It works with engine off and can work with any fuel pressure tester. |
Polarity Reverse Connection Protection & Short Circuit Protection This fuel injector cleaner and tester is deigned with power input reverse connection protection and output short circuit protection function. In the case of a damaged fuel injector or a short circuit of the pulse output terminal, the power indicator light of the fuel injector cleaner tool will flash to prompt you. Besides, this injector tester cleaner kit can also be modified for relay testing or solenoid valve testing, and other modifications should be carried out under the guidance of professionals. |
Specification: Power supply : 12V battery or DC 12V (recommended 2A) power adapter Working conditions: 0°C-40°C; relative humidity ≤80% Storage conditions: -20°C-50°C; relative humidity ≤85% Unit Size: 120*80*25mm Weight: 0.34kg Operation Instructions: 1). Turn off the car's engine. 2). Remove the wire plug of the vehicle injector to be tested, and then connect the two pulse output terminals of the fuel injector tester to the vehicle injector. 3). Then connect the red clip of the injector tester to the positive terminal of the 12V car battery, and connect the black clip of the injector tester to the negative terminal of the car battery. 4). Insert the DC plug into the port of the fuel injector tester. 5). Press MODE SET key to select the desired pulse signal output mode, and the screen will display the currently selected mode. Package Include: 1* Fuel injector cleaner tester with 2 pulse output teminal, 40inch power cord with 2 battery clamps, 4* Blue universal fuel injector flush cleaner adapters 1* Portable carrying bag. |
Payment
International Buyers Please Note: