SHYSKY 24V DC Micro Brushless Submersible pump DC55K-24250S, 80W, 25M Lift, 550 L/H Flow Rate, Low noise, IP68 Waterproof, For Water Circulation Pressurization Cooling 

Widely Applied For Industrial, Gardening, Medical Systems




About this item

  • SHYSKY DC55K-24250S Water pump, External diameter of inlet: 10mm; External diameter of outlet: 9.5mm; Max static lift: 25m; Max horizontal flow rate: 550L/H.Typical feature is with quite high lift (output pressure) value, but with relatively low flow rate, suitable for some micro pressure system. (Certain parameters, cable length and other specific functions can be specially CUSTOMIZED, based on exact discussion and certain MOQ & lead time.) 

  • Brushless DC motor, also known as EC motor; Magnetic Driven (NO DIRECT AC 100-240V POWER CONNECTION, PROHIBITED); Small size but strong; Low consumption & High Efficiency; Long time continuous working with low noise; Explosion - proof; Low noise about 40dB.

  • Submersible, IP68 Waterproof; Max Working Temperature: 100 degree; Wide range of working voltage; Maintenance - free; Can be used to pump water, oil, other non-corrosive liquids (special liquids are needed to be pre-tested in advance). 

  • Variety Power: DC electric source, Battery or Solar Panel, etc; Soft Start with Low in-rush current, Especially suitable for Solar SYS who can not provide over-high startup impulse current; OEM and ODM are accepted based on MOQ and exact inquiry of customers. 

  • NEW FEATURE: DRY-RUN PROTECTION feature is integrated now in default. Pump works at rated voltage: When there exists no/ in-sufficient in-flow (or significant air bubble contained), it is DRY RUN scenario and protection will be triggered: Pump will access stop-run-stop-run---cycle, greatly reducing rotation. When flow comes sufficiently again, pump will re-access normal run. It greatly reduces physical friction between parts and heat generated, yet, not completely eliminate the impact. 


DC55K-24250S High Lift Micro Brushless DC Water Pump

Dimension and weight98.8mmx77.5mmx78mm; Approx. 720g
External diameter of outlet9.5mm
External diameter of inlet10mm
Driving mechanismBrush-less, magnetic isolated design
Material of pump shellPPS+30%GF (Optional if for customization)
Condition of useCan continuously work, submersible or land use (not self-priming)
Suitable mediumWater, oil, or non-corrosive fluids (Pre-test needed for special liquid)
Max working temperature100℃(for S/A sub-series) (suggested to be under 80C)
Power consumption80W (for 24VDC version)
Rated voltage24Vdc
Working voltage range10Vdc ~ 28Vdc (for 24VDC version)
Max load current3.3A (for 24VDC version)
Max horizontal flow rate550LPH (for 24VDC version)
Max static lift25M (for 24VDC version)
Noise class<40 dB, at appr. 1m distance
Waterproof classIP68(suitable for submersible installation)









NOTE: DC55K-24250S Water pump, 24VDC, rated power 80W at 24VDC. Max. Static lift appr. 25m at 24VDC and Max. Horizontal flow rate appr. 550LPH at 24VDC.

(CANNOT BE SELF-PRIMING; NO DRY WORK) 

Pay Attention: No dry work without water or with little water; otherwise, pump may be hurt. When users get pump, it’s recommended that a pre-test can be done in advance, then install to relevant application: get a bucket of water, locate the pump into water and power the pump with a matching DC power supply, check the work and performance of pump.

As to control box of pump, strictly speaking, it’s not recommended to be located in the water; if indeed have to, waterproof tape is recommended to be firmly wrapped in advance. Of course, location out of water is more recommended.


1, As micro brushless dc pump, it works via electronic commutation while not brush friction, so there exists no loss caused by brush friction.


Pump works with relatively high efficiency.

Both internal control circuit and stator part are completely potted inside pump body with epoxy material, 

completely physically separated from external fluid environment and completely waterproof.

2, Pump supports continuous long time work with relatively low noise at normal working environment.

Land use or submersible installation can be both OK, but it CANNOT BE SELF-PRIMING, just make sure that fluid can actively flow passing through inlet/outlet.

3, No DIRECT AC Power connection or over-voltage DC Power supply.

4, About power polarity: DC head connector, then it will be: INNER is Positive, OUTER is Negative.

5, to avoid possible misunderstanding of relevant parameters, here we also say something about flow rate value & max static lift value of pump products: 

For static lift value, it means the max vertical height of flow column when outlet is connected with external matching hose/tube, when pump works at rated voltage.

For max flow rate value, it means the max flow rate of pump at horizontal level, when pump works at rated voltage. The higher the height, the lower the flow; 

when height reaches lift value, flow rate becomes zero.Note that lift value and spraying/shooting height of pump are completely different. So dear users, please do not be confused.

Package includedes: 

1 x DC55K-24250S Micro Brushless DC Water Pump 

(No power supply is included. If power supply is AC/DC power adapter, output capacity of adapter should be 24VDC, >= 4A.)




Shopping

1. Please make sure whether item(s) you want to order is/are the right one(s) you need and we do advise that customer friends pre-contact us about relevant issue if you are not sure, to avoid possible extra waste caused by inappropriate choice.

2. Import duties, taxes and charges are not included in item price or shipping charges and Customs clearance is buyer’s responsibility. Please check with your local Customs authorities before purchase.

 (If respected customer doesn't undertake Customs clearance duty, all relevant loss will be customer's duty; when in need, we as responsible vendor will provide all essential documents to help complete Customs clearance, within our ability)