Product Description
Product Name |
SpeedyBee F405 V3 30x30 Flight Controller |
MCU |
STM32F405 |
IMU(Gyro) |
BMI270 |
USB Port Type |
Type-C |
Barometer |
Built-in |
OSD Chip |
AT7456E chip |
BLE Bluetooth-compatible |
Supported. Used for Flight Controller configuration (MSP should be enabled with Baud rate 115200 on UART4) |
WIFI |
Not supported |
for DJI Air Unit Connection Way |
Two ways supported: 6-pin connector or direct soldering. |
6-pin for DJI Air Unit Plug |
Supported. Completely compatible with DJI O3/RunCam Link/Caddx Vista/for DJI Air Unit V1, no wire is needed to be changed. |
Blackbox MicroSD Card Slot |
*Betaflight firmware requires the type of the microSD card to be either Standard (SDSC) or High capacity (SDHC), so extended capacity cards (SDXC) are not supported(Many high-speed U3 cards are SDXC). Also the card MUST be formatted with the FAT16 or FAT32 (recommended) filesystems. So, you could use any SD card less than 32GB, but the Betaflight can only recognize 4GB maximum. We suggest you use this 3rd party formatting tool and choose 'Overwrite format' then format your card. Also check out here for the recommended SD cards or buy the tested cards from our store. |
BetaFlight Camera Control Pad |
Yes(CC pad on the front side) |
Current Sensor Input |
Supported. For SpeedyBee BLS 50A ESC, please set scale = 386 and Offset = 0. |
Power Input |
3S - 6S Lipo(Through G, BAT pins/pads from the 8-pin connector or 8-pads on the bottom side) |
5V Output |
9 groups of 5V output, four +5V pads and 1 BZ+ pad( used for Buzzer) on front side, and 4x LED 5V pads. The total current load is 2A. |
9V Output |
2 groups of 9V output, one +9V pad on front side and other included in a connector on bottom side. The total current load is 2A. |
3.3V Output |
Supported. Designed for 3.3V-input receivers. Up to 500mA current load. |
4.5V Output |
Supported. Designed for receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load. |
ESC Signal |
M1 - M4 on bottom side and M5-M8 on front side. |
UART |
6 sets(UART1, UART2, UART3, UART4(Dedicated for Bluetooth connection)), UART5(Dedicated for ESC telemetry),UART6 |
ESC Telemetry |
UART R5(UART5) |
I2C |
Supported. SDA & SCL pads on front side. Used for magnetometer, sonar, etc. |
Traditional Betaflight LED Pad |
Supported. 5V, G and LED pads on bottom of the front side. Used for WS2812 LED controlled by Betaflight firmware. |
Buzzer |
BZ+ and BZ- pad used for 5V Buzzer |
BOOT Button |
Supported. |
RSSI Input |
Supported. Named as RS on the front side. |
Smart Port / F.Port |
Not supported |
Supported Flight Controller Firmware |
BetaFlight(Default), INAV (INAV firmware can only use Multishot (recommended) and OneShot125. Please note that DShot is not supported.) |
Firmware Target Name |
SPEEDYBEEF405V3 |
Mounting |
30.5 x 30.5mm( 4mm hole diameter) |
Dimension |
41.6(L) x 39.4(W) x 7.8(H)mm |
Weight |
9.6g |
Product Name |
SpeedyBee BLS 50A 30x30 4-in-1 ESC |
Firmware |
BLHeli_S JH50 |
Wireless Configuration |
Full Configuration Supported in the SpeedyBee app |
PC Configurator Download Link |
|
Continuous Current |
50A * 4 |
Burst Current |
55A(5seconds) |
TVS Protective diode |
Yes |
External Capacitor |
1000uF Low ESR Capacitor(In the package) |
ESC Protocol |
DSHOT300/600 |
Power Input |
3-6S LiPo |
Power Output |
VBAT |
Current Sensor |
Support (Scale=386 Offset=0) |
ESC Telemetry |
Not supported |
Mounting |
30.5 x 30.5mm( 4mm hole diameter) |
Dimension |
45.6(L) * 44(W) * 6.1mm(H) |
Weight |
13.8g |
Welcome to our store, we are doing BGNING brand products, our factory mainly do the metal parts of the camera accessories, the price is the factory price, wholesale price, we have a large number of inventory shipments fast, the need for large quantities of wholesale can contact me, I can give you the highest discount price!
1. All price does not include any taxes or extra fees. We are not responsible for the problems caused by customs clearance.
2. Orders processed timely after the payment verification.
3. We only ship to confirmed order addresses. Your order address MUST MATCH your Shipping address.
4. The images shown are not the actual item and are for your reference only.
5. SERVICE TRANSIT TIME is provided by the carrier and excludes weekends and holidays. Transit time may vary, particularly during the holiday season.
6. If you have not received your order after the Estimated Delivery of Shipping Method, please contact us in advance. We will trace your order and get back to you asap.
(Please notice that we can't decide your decisions about choosing to ship methods, which means you need to check carefully with the estimate delivery time and promise delivery time) Your satisfaction is our top priority!
1. You have 30 days to contact us No reason to return within 30 days after signing,The shipping cost is Seller .
2. All returned items MUST BE in the original packaging and you MUST PROVIDE us with the shipping tracking number, specific reason for the return, and your order ID.
3. We will refund YOUR FULL WINNING BID AMOUNT, upon receipt of the item in its original condition and packaging with all components and accessories included, AFTER BOTH Buyer and Seller cancel the transaction from ebay. OR, you may choose to have a replacement.
4. We will bear all the shipping cost if the product(s) is (are) not as advertised.
We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important. We request that you contact us immediately BEFORE you give us neutral or negative feedback so that we can perform up to your satisfaction.
It is impossible to address issues if we do not know about them!