Wilckens 5L Base and Roof Paint | anthracite
• Matt
• High coverage
• Scuff and weather resistant
• UV-stable, lightfast
• Can be diluted with water
• din EN 13300: Wet abrasion class 2
Description
Ready-tinted emulsion exterior wall paint. Highly opaque, abrasion- and weather-resistant emulsion paint for outdoor use. Easy to clean and protects against wind and weather. Water vapor diffusible, UV-stable, lightfast and low in solvents.
Lightfastness
Very good
Weather resistance
Weather-resistant according to VOB Part C din 18363.
compatibility
All colors can be mixed with each other.
Available shades
• Slate
• Stone gray
• Havana
• Brick red
• Anthracite
Gloss level
at a 60° measuring angle according to din 67530, shiny. Gloss level cannot be measured >100.
Purpose of use
Particularly suitable for weatherproof new and renovation coatings in driving rain areas of wall and base surfaces made of concrete, plaster, masonry and old paint as well as for roof tiles and fiber cement panels.
Paint structure and application technology
Read the label before use! The surface must be clean, firm, dry and free of release agents (forming oils, grease or similar). Completely remove old, unsustainable coatings. Pre-treat highly absorbent or friable sandy substrates, including roof tiles and fiber cement panels, with a deep primer. New unpainted plasters must dry for at least 4 weeks. Thoroughly remove any existing growth beforehand by brushing, scraping or washing, if necessary with green growth remover or similar. The bases must be protected against rising moisture from the ground and from the inside. Standing water on the coating must be avoided; the roof pitch should be at least 3°. In the case of contiguous surfaces, ensure that the containers are the same in batches. Stir the container well.
1. Coating structure on plaster and concrete
a) Prepare the substrate accordingly.
b) Prime or solidify critical substrates accordingly.
c) 1 x pre-paint with base and roof paint with 5% to 10% water
diluted.
d) 1 to 2 top coats undiluted.
2. Paint build-up on old paint or renovation paint
a) Prepare the substrate accordingly.
b) Prime or solidify critical substrates accordingly.
c) 1 x pre-paint with base and roof paint diluted with 5% water.
d) 1 to 2 top coats undiluted.
Diluent for rolling, brushing, spraying
Water
Tool
Paint roller, flat brush, airless sprayable
Cleaning the tools
Clean with soap and water immediately after use.
fertility
Approximately 6 m²/l, for one coat, depending on the absorbency of the surface.
Drying (at +20°C, 65% relative humidity)
Reworkable: after about 8 hours
Lower temperatures and higher humidity extend the drying time!
ingredients
Acrylate copolymer dispersion, titanium dioxide and inorganic colored pigments, carbonate and silicate fillers, water, additives, preservatives: 2-methyl-2(H)-isothiazol-3-one, 1,2-benzisothiazol-3-(2H)-one, zinc pyrithione . Can cause allergic reactions.
VOC value
EU limit value for base & roof paint (Cat.A/c) 40 g/l (2010). Base & roof paint contains a maximum of 39 g/l VOC.
WGK
1
GISBAU code
M-DF 01
Danger warnings | Safety advice
Store closed containers in a cool, but frost-free place. Do not use the substrate or ambient temperature below + 5 °C and do not use it in strong sunlight. Keep out of reach of children. If medical advice is required, have packaging or label available. Avoid eating, drinking or smoking while using the paint. Also follow the usual protective measures when processing low-pollutant paints. In case of contact with skin and eyes, rinse immediately with plenty of water. Do not allow to enter drains, waterways or soil. Do not inhale spray mist. Use combination filter A2/P2 for spraying work and dust filter P2 for sanding work. Only send empty containers for recycling; dried material residues can be disposed of as household waste; liquid material residues can be taken to the collection point for used paint. Please note the application and processing instructions mentioned in our product information as well as the current safety data sheet.