Mini W5100
A variety of interface can choose: direct bus, indirect bus and the SPI bus.
Support hardware TCP/IP protocol stack, supports TCP, UDP, ICMP and IGMP, IPv4, ARP, PPPoE.
As many as four separate port
Internal integration 16 kbyte transceiver cache
Indicate the output, a variety of information including RX and TX, Full/Duplex, Colision, Link, Speed
Support automatic polar transformation (DMI/MDIX)
3.3 V power supply, IO is compatible with 5 V voltage signal
Take so, double row 2 * 2.0 mm pin 14
Size :5.2x3x1.5cm (length x width x high )
Package Included:1 x TOP Mini W5100 LAN Ethernet Shield Network Module board for Arduino Best
Support hardware TCP/IP protocol stack, supports TCP, UDP, ICMP and IGMP, IPv4, ARP, PPPoE.
As many as four separate port
Internal integration 16 kbyte transceiver cache
Indicate the output, a variety of information including RX and TX, Full/Duplex, Colision, Link, Speed
Support automatic polar transformation (DMI/MDIX)
3.3 V power supply, IO is compatible with 5 V voltage signal
Take so, double row 2 * 2.0 mm pin 14
Size :5.2x3x1.5cm (length x width x high )
Package Included:1 x TOP Mini W5100 LAN Ethernet Shield Network Module board for Arduino Best
NANO W5100
This add-on module allows you to connect the Arduino Nano to the internet. You get all of the benefits of using the Arduino Nano. It is fully assembled with long pin headers so you don need to purchase and solder the headers separately. you get the same stackable benefits as the Arduino shields and can run the same code.
It is based on the Wiznet W5100 Ethernet chip which a network (IP) stack capable of both TCP and UDP. Use the Ethernet library to write sketches which connect to the internet using the add-on module.
The ETHERNET-NANO connects to an Arduino Nano using female long wire-wrap headers which extend through the board for the breadboard connections. This keeps the pin layout intact and allows another add-on module to be stacked on top or bottom.
The Micro-SD card slot can be used to store files for serving over a network. It is compatible with the Ethernet library for the Arduino 0022 and later. The SD card library is included in the standard Arduino distribution。
The Arduino Nano communicates with both the W5100 and MicroSD card using the SPI bus. This is on digital pins 11, 12, and 13 on the Nano. Pin 10 is used to select the W5100 and pin 4 is used for the MicroSD card. These pins cannot be used for General Purpose Input/Output(GPIO).
Note that because the W5100 and MicroSD card share the SPI bus, only one can be active at a time. If you are using both peripherals in your program, this should be taken care of by the corresponding libraries. If you're not using one of the peripherals in your program, however, you'll need to explicitly deselect it. To do this with the MicroSD card, set pin 4 as an output and write a high to it. For the W5100, set digital pin 10 as a high output.
The ETHERNET-NANO provides a standard RJ45 ethernet jack.
Package Included:1 x NANO W5100 Ethernet Shield Network Expansion Board for Arduino Nano V3.0 TOP
It is based on the Wiznet W5100 Ethernet chip which a network (IP) stack capable of both TCP and UDP. Use the Ethernet library to write sketches which connect to the internet using the add-on module.
The ETHERNET-NANO connects to an Arduino Nano using female long wire-wrap headers which extend through the board for the breadboard connections. This keeps the pin layout intact and allows another add-on module to be stacked on top or bottom.
The Micro-SD card slot can be used to store files for serving over a network. It is compatible with the Ethernet library for the Arduino 0022 and later. The SD card library is included in the standard Arduino distribution。
The Arduino Nano communicates with both the W5100 and MicroSD card using the SPI bus. This is on digital pins 11, 12, and 13 on the Nano. Pin 10 is used to select the W5100 and pin 4 is used for the MicroSD card. These pins cannot be used for General Purpose Input/Output(GPIO).
Note that because the W5100 and MicroSD card share the SPI bus, only one can be active at a time. If you are using both peripherals in your program, this should be taken care of by the corresponding libraries. If you're not using one of the peripherals in your program, however, you'll need to explicitly deselect it. To do this with the MicroSD card, set pin 4 as an output and write a high to it. For the W5100, set digital pin 10 as a high output.
The ETHERNET-NANO provides a standard RJ45 ethernet jack.
Package Included:1 x NANO W5100 Ethernet Shield Network Expansion Board for Arduino Nano V3.0 TOP
ENC28J60
100% brand new and high quality
Chip board ENC28J60-I/SO.
The board 25MHZ crystal.
The network interface board HR911105A.3.3 V power supply pin
Specifications:
Size: 58*34*17 mm
Net weight:15 g
Package weight:25 g
Color:Blue
Package Included:1PCS*NEW ENC28J60 Ethernet LAN / Network Module For 51 AVR STM32 LPC
Chip board ENC28J60-I/SO.
The board 25MHZ crystal.
The network interface board HR911105A.3.3 V power supply pin
Specifications:
Size: 58*34*17 mm
Net weight:15 g
Package weight:25 g
Color:Blue
Package Included:1PCS*NEW ENC28J60 Ethernet LAN / Network Module For 51 AVR STM32 LPC
MiNi ENC28J60
Brand new and high quality.
chip board ENC28J60/SS.
the board 25MHZ crystal.
the network interface board HR911105A.
3.3 V power supply pin.
Size:5.cm x 2cm x 1.5cm /1.92''x0.72''
Weight: 11g
Package Included:1 x MiNi ENC28J60 Ethernet LAN Network Module For Arduino SPI AVR PIC LPC STM32
chip board ENC28J60/SS.
the board 25MHZ crystal.
the network interface board HR911105A.
3.3 V power supply pin.
Size:5.cm x 2cm x 1.5cm /1.92''x0.72''
Weight: 11g
Package Included:1 x MiNi ENC28J60 Ethernet LAN Network Module For Arduino SPI AVR PIC LPC STM32
Nano ENC28J60(Blue)
controller: Microchip's ENC28J60 ethernet / HR911105A
works as server or client
comes with efficient library and examples
direct plug puzzle board, NO soldering needed.
Shipping Included:1 x Mini ENC28J60 Webserver Module Ethernet Shield Board For Arduino Nano v3.0
works as server or client
comes with efficient library and examples
direct plug puzzle board, NO soldering needed.
Shipping Included:1 x Mini ENC28J60 Webserver Module Ethernet Shield Board For Arduino Nano v3.0
Nano ENC28J60(Red)
With this Ethernet Shield, your Arduino Nano board can be used to connect to internet
controller: Microchip's ENC28J60 ethernet / HR911105A
works as server or client
comes with efficient library and examples
direct plug puzzle board, NO soldering needed.
Package included：1PCS x ENC28J60 Ethernet Shield for Arduino Nano 3.0 RJ45 Webserver Module
controller: Microchip's ENC28J60 ethernet / HR911105A
works as server or client
comes with efficient library and examples
direct plug puzzle board, NO soldering needed.
Package included：1PCS x ENC28J60 Ethernet Shield for Arduino Nano 3.0 RJ45 Webserver Module
ENC28J60 Style 2
ENC28J60/SS chip, SSOP28 package
25MHZ crystal
RJ45 connector HR911105A isolation transformer
5V or 3.3v pin power supply board AMS1117-3.3 chip
SPI communication interface
2 * 6 double pin connector
Package Included:1 x ENC28J60 Ethernet LAN Network Module
Package Included:1 x ENC28J60 Ethernet LAN Network Module
Am 06.08.19 hat der Verkäufer die folgenden Angaben hinzugefügt: