5" Diameter Cylinder, High Pressure Line, 16 GPM Log Splitter Pump, Mount, Auto-Return Detent Valve and Coupler Kit w/Bolts/Fittings

From Tool Tuff Direct - Your Source for Log Splitter Parts Since 2012!

 

Build your own log splitter setup with this convenient kit!  Bolt this to your engine, and run some suction/discharge hoses and you're in business!  

Picture shows valve connected to cylinder - it is shipped separate, just screw in the included fittings with some thread tape and you'll be golden! 


INCLUDES: 

16 GPM 2 Stage Hydraulic Log Splitter Pump

 The 2-stage pump can give you faster cycle times and higher possible pressure with a small engine.  Excellent for use on log splitters.  85% efficient.

Suggested applications: Presses, Log Splitters, Clamping Units and Compactors

 

Specifications:

  • New Hydraulic Log Splitter Pump 16 GPM @ 3600RPM
  • Model # GP-CBN-160
  • Shaft: ½”
  • Inlet port: 1”
  • Outlet port: ½”
  • 7- 1/4" L with shaft
  • 5- 5/8” L without shaft
  • 3” across body
  • 3 -3/8” across mounting surface
  • Minimum 8 HP or larger gas engine, direct drive only, horizontal shaft (can be mounted vertical or horizontal)
  • For use with open center hydraulic systems only
  • First Stage: 13 GPM @ 650 PSI
  • Second Stage: 3 GPM @ 2500 PSI
  • Maximum pressure: 4000 PSI
  • Bolt circle: 2.83in.
  • 4 holes spaced 2” on center
  • Mounting hole diameter: .344in.
  • Woodruff key: 1/8in.
  • Rotation is clockwise
  • Flow rates on the hi-low tandem pumps are 0.256 cu in/rev on the low flow and 0.793 cu in/rev on the high flow pump.
  • This 2 stage pump can give you much faster cycle times and higher possible pressures with a small engine. Excellent for use on log splitters. 85% efficient.
  • Model GP-CBN is a HI/LO hydraulic gear pump with 12 different displacement combinations with maximum pressures of 900 psi for the low pressure pump and 3000 psi for the high pressure. The change from LO to HI pressure is automatic with the LO side pressure pre set from 400 psi to 900 psi.
  • The HI/LO section of the pump is all aluminum and the end plates are cast steel. Applications for the HI/LO pump are log splitters, presses etc where rapid movement of the cylinder at low pressure is required prior to automatically switching to the high pressure mode to meet load requirements.

Lovejoy LO90 Coupler 

This kit includes two coupler halves and one rubber spider. The default set is L090 1/2" and 1". Please message us if you need a different size. You can choose from L090 3/4" 5/8" 7/8" 1" or 1-1/8"

A7 Auto-Return Log Splitter Valve  

(We have other valves available - if the schematic looks different than your valve, message us and we can substitute it)

Valve Specs:

Single spool, Open center.

·         Max pressure rating: 3500psi.

·         Relief valve set at 3100psi but is adjustable.

·         Working ports ½”NPT.

·         In/Out ports ¾” NPT

·         Detent Pressure set at 700 psi but is adjustable.

·         Compatible with most splitters (SpeeCo, MTD, Brave, Swisher etc)

·         Threaded end cap for easy detent adjustment


Mounting bracket holes (4) are 5/16-18 thread pitch and are spaced 1" x 2-5/8" apart

This is the next generation in log splitter valves. The detent is usually what wears out and causes valves to fail. This valve allows user to adjust the kick out pressure to what they need and as detent balls and grooves wear.

Pump to Mount Bolts, Lock Washers, Nuts

  • Includes the required bolts, nuts and lock washers required to mount the pump to the mount.  You'll supply your own engine mounting bolts.  

5" Bore x 24" Stroke Hydraulic Log Splitter Cylinder (OEM Replacement for TSC, Huskee,SplitMaster, Oregon, SpeeCo, Etc)

In addition to being great "build it yourself splitter" parts, our cylinders will replace your original worn-out double acting TSC, Huskee, SplitMaster, Oregon, SpeeCo and many other Log Splitter cylinders that have the double-ear mounting clevis as shown in our pictures without any modifications needed. Most of the time they are direct-fit.  All fit-up dimensions are listed in the picture section of this add.

Quick Specifications:

  • All welded design
  • Direct replacement for TSC Husky, SplitMaster, Oregon, SpeeCo and many others
  • This cylinder to be used with any 2 stage gear pump (Common are 11gpm, 13gpm and 16gpm)
  • Provides approximately 27 tons of splitting force
  • Double-Acting (Forward and Reverse
  • Rebuildable (seals can be replaced)
  • 2" Chrome rod machined to 1-3/4" at end with 9/16" mounting hole for wedge mounting
  • Double mounting clevis design to accept 1-1/8"
  • 24" stroke
  • 5" diameter bore
  • 1/2" NPT hydraulic ports
  • 3500 maximum operating pressure
  • Painted black
  • 1-1/8" Clevis mounting holes to mount cylinder at front of beam
  • Generally provides about 35 tons of splitting force.

Pump Mount for hydraulic log splitter, 8hp-15hp. Speeco, Brave, Northern wood

 

Pump Mount for Log Splitters and other equipment. Direct replacement for SpeeCo, Splitmaster, Oregon, Husky 28, 33, 34 and 35t units. 

  • Length: 5-1/4"
  • Pump Bolt Circle: 2-3/4", or 2" square. Holes tapped for 5/16" bolt
  • Engine Bolt Circle: 5" or 3-1/2" square.
  • Cast Iron construction.
  • Works with Halidex, MTD, Deli and other 11 gpm - 16 gpm pumps.
  • Mounts to Briggs, Honda, Kohler, Subaru 8-15 hp motors


PAYMENT

·        We accept PayPal payment and Credit Cards. 

·        We only ship to confirmed PayPal addresses or to the billing address on the credit card used to make your purchase. 

·        If you need anything regarding payment, please feel free to contact us via eBay Message.

SHIPPING

·        Please note! We use FedEx or USPS for shipping. We maintain the right to change carrier, without any notice to the buyer, so you receive your item(s) as fast as possible.

·        Your item will be dispatched within 1-2 business days after your valued payment.

·        We currently only ship to the 48 continental states and we do not provide international shipping.

Warranty

·        We Stand behind all of our products for 6 months

·        We will ship out replacement or replacement parts at our discretion.

RETURNS

·        If you are not satisfied with your purchase for any reason, you may return a product within 14 days.

·        Buyers must pay the return shipping charge unless stated otherwise.

·        Return order must be in the same condition as received. If an item received was damage or defective, please notify seller within 5 days of receipt of item.

·        Prior to returning any order, please contact us via email for return address. All return orders should include your eBay user ID, eBay item number, and a brief reason for the return order.

ABOUT US

·        We strive to provide the best possible service to our customers. If you are satisfied with our product and service, please leave us a 5 STAR POSITIVE RATING feedback as soon as you receive your order. That will help us to maintain good reputation on Ebay and it's VITAL for us. 

·        If you are DISSATISFIED for any reason, please DO contact us via eBay message BEFORE leaving neutral, negative feedback or opening a case on eBay. We work hard to make sure you are satisfied and we will resolve any problem for you and will always leave positive feedback to all our customers.

 

CONTACT US

·        We can be reached by eBay message, please feel free to contact us about your questions, but please DO NOT open a dispute or give us bad feedback. We'll reply in 24 hours during business days. Please give us one chance resolve the problem.

Thank you for looking and your valuable business. 

·        Hours of Operation are Monday Through Friday 9 am to 5 pm MST