100% Brand New and High Quality!
Introduction:
Body used profiles and plastic, small size, light weight, USB interface, GRBL control system, learning, entry preferred. Can use carving knife, but also can use laser engraving.
Can be engraved plastic, wood, acrylic, pvc, pcb, wood and the like material.
Specification:
Main application:
Can be engraved plastic, wood, acrylic, pvc, pcb, wood and the like material.
I. GRBL USB port cnc engraving machine control board, 3 axis control
Specification:
Connection: USB (USB-CH340)
Software: GRBL controller, UniversalGcodeSender
Input voltage: 24VDC (12-24VDC)
Stepper motor: support 24V 2A
Spindle motor: support 24V 10A (supports PWM0%-100%)
Master chip: atmel 328P (arduino nano)
Spindle drive chip: MOSFET (recommendation 12~36V, current : within 10A )
Spindle PWM speed: Support
Support stepper motor: 12V, maximum current of 2A or less is recommended within 1.5A and additional heat. (Any stepper motor 42, 57)
Laser engraving: Support
Power Interface: 5.5-2.5mm DC interface
Support system: win-xp,win7,win8,win10
Advantage
add the outer casing: mainly for the bare board of the control board, short circuit problem during use
add
the power button switch (this switch is the power supply control
signal, there is no large current passing through the switch, do not
worry about the switch size)
Cancel the drive module, integrated
imported stepper motor drive, with short circuit protection, no need to
worry about module damage. And integrated heat dissipation aluminum
alloy
add the fan to force heat dissipation.
add offline
recognition to insert offline modules and computers at the same time.
Offline will automatically identify if there is computer control.
Enhanced spindle drive. Can support 20,000 rpm spindle. Support for larger power spindles
1.Improved power interface: original plastic interface changed to full metal shielded interface
2.Improved USB interface: The original USB interface is patch soldering, transport collision and improper use, easy to drop, now changed to plug-in, very strong
3.The spindle drive increases the optocoupler isolation, which makes the control board generate less heat, and the spindle speed adjustment is more linear and safer.
4.The stepper motor drive increases the self-recovery fuse. When a short circuit or fault occurs, the power supply is cut off and the fault indicator light is displayed.
5.The 12V step-down increases the self-recovery fuse. When a short circuit occurs, the power can be cut off in time to avoid damage.
6.Optimize layout, control area and drive area separation, run more stable"
GRBL controller Function:
SD shows it is SD card condition, turn on power supply after insert SD card, otherwise, it won't work. SD card capacity 4G could be recognized.
Press X- or X+ button to switch
Control:Press confirmation button to access manually controlling page
File:Press confirmation button to access file page
Set:Press confirmation button to access setting page
On the off-line controller, buttons control corresponding actions.
SPN is spindle controlling,should press SPIN.
Fan is fan controlling, should press SMOD.
Note: To exit this page, should press back button longly. after exit, save the current location as engraving starting point X0Y0Z0
Note: system can recognize max 100 available files one time (***.TXT***.txt***. NC***.nc***.CNC
***.cnc***.TAP***.tap could be recognized),not support files with long name.
Press Y+ or Y- to choose files need to be engraved, press confirmation button to access engraving page.
Press ok to start engraving
If you want to stop during engraving, press back button longly, then back to the file selection page(machine will not stop at once, as GRBL controller has already saved a part of G code, will stop after carry out completely).
The left words show the machine moving distances every time you press the button on the condition of manually controlling, press Y+ or Y- to choose, default 1mm each time.
Press X- or X+ for switchover setting.
The right words show Communication baud rate setting, default 9600
After setting, press confirmation button to save, then press back button to exit setting page.
Note: the setting parameters can not be saved on the condition of electricity outage, it will be default value when turn on next time.
Shipping
Please open the package and check if there are some damages before sign, if there are some damages , please do not sign and contact us immediately
Items will be shipped within 1-2 days upon the receipt of payment.
Payment
We accept paypal payment, all Paypal must be confirmed(shipping and billing address must match and correct and it need tell us your telephone no for delivery)
Problem&Feedback
Please give us the opportunity to resolve any problem when you have, we concern your problem and we will try our best to resolve it.
We are a new member in ebay now, and need understand both of sides
Pls email us before you want to leave any negative feedback
Refund
When you have the parcel, and not satisfied the goods or it is other problem like as broken,pls tell us the detail reason and provide the photos
Any reason required for all refund. Item must be in it's original condition and no physical damage. Buyer responsible for all shipping cost
Contact us
Welcome worldwide customer inquire and questions, we will try to do our best to feedback customer’s email within 1-2 business days,if not pls check the mail box again
Customer’s satisfaction is very important to us.