Kerawax 4600 pillar bend.

Kerawax 4600 is a wax blend specifically developed for the production of pillar candles. It is suitable for further blending with fragrances and oil soluble dyestuffs.

Statement:

Formulated from materials whose refining history is fully traceable.
Does not contain or come into contact with animal or GMO products at any stage of its manufacture.

Does not contain residual solvents as per guidelines CPMP/ICH283/95.
Has not been tested on animals by ourselves or on our behalf.

Manufacturers notes:

Karawax 4600 requires no additives and has an outstanding stability with no experienced shelf life issues. Old or partial candles may be re-melted and the wax reused. Waxes should be stored in a cool dry location away from direct heat, sunlight and moisture.

Moulds:

Moulds should be clean and at room temperature. Your mould may need “conditioning” before using Kerawax 4600. If your candle does not release well after setting, clean the mould, re-melt the wax and re-pour. This will have “conditioned” the mould.

Colour:

Most dyes work with Kerawax 4600; powder, liquid, chips, block etc. Pigments do not dissolve in Kerawax 4600. When using powder dyes heat the wax to 80*C, add the dye and mix until dissolved. Powder dyes may also be dissolved in fragrance and then added to the melted wax, be sure the dye has melted completely before adding. When using powder dyes dissolved in fragrance, liquid dyes, colour blocks chips or no dye heat the wax to 70*C. If you wish to make your candle darker or “richer” add a little black dye to the colour you are using.

Fragrance:

Kerawax 4600 may be used with almost any fragrance at levels of up to 10-12%. Burn pool size and depth greatly affect scent throw so correct wicking is paramount. Some fragrances may react poorly with the wax causing bleed, objectionable surface finishes or poor flame quality. In this case try a lower concentration, a different fragrance or manufacturer to eliminate it.

Wicking:

Kerawax 4600 may require larger wicking sizes than traditional paraffin waxes. They tend to burn more down than out allowing them to have longer burn periods. Scent, colour and candle configuration have a great impact on the best wick choice. Too large of a wick may cause sooting, accelerated burn times and guttering (wax leaking through the side of the candle). Too small a wick will cause tunnelling and produce a smaller flame.  Keep wicks trimmed to 1/4 inch. If you experience poor flame quality or stability, try a different type of wick. Test burning should be done after the candle has had a chance to sit for 48 hours after pouring.

Melting:

When using pre dispersed or no dye at all, heat the wax to 70*C. For powder dye use, heat the wax to 90*C, add the dye and mix until dissolved. Undissolved powder dyes will b seen as dark specs on the bottom of the mixing container. Temporary high temperatures such as 90*C have no adverse effect as long as the wax is cooled back down quickly. Higher temperatures may cause the wax to discolour. Allow the wax to cool to your desired pour temperature, add the fragrance and mix well. Be sure to stir/mix the wax while melting. Avoid using containers containing copper and zinc as this may accelerate discolouration. Stainless steel is the material of choice although mild steel is acceptable. Digital temperature probes are readily available and are a safer choice than the traditional mercury in glass type.

Pouring:

Pour temperatures may vary according to mould type & size, fragrance & dye used and the effects you want to achieve. Scent should be added and mixed right before pouring or at higher temperatures if desired. If you experience difficulties with your pour temperature try a lower or higher temperature in increments of 10*C. Consider pouring into pre heated moulds for an extra glossy finish.

Double-pour:

When using Kerawax 4600 two pours are required with larger candles such as 3 & 4 inch pillars. Dow the first pour at 65*C by filling the mould to the top and allowing the candle to cool until it’s still warm with a congealed centre that has no liquid. If the top of the mould (bottom of the candle) has “skinned” over and left a void inside, poke two holes into the candle near the wick and pour a second time at 60*C.

Making votives:

Make the first pour at 65*C by filling the mould to within 1/8 inch from the top. Allow the candle to cool until it’s still warm with a congealed centre that has no liquid. If the top of the candle has “skinned” over, create two holes near the wick and pour a second time at 60*C to completely fill the votive mould.

Candle cooling and mould release:

Cool undisturbed candles at room temperature (about 25*C). The moulds should be about 1/4 to 1/2 inch apart to allow air circulation for even cooling. Kerawax 4600 is self releasing. Spray silicone mould  release may be used in the unusual event of sticking. If difficult mould release is experienced, placing the mould/candle in the refrigerator for a few minutes will cause the candle to release. Candles should be allowed to sit undisturbed for 48 hours before test burning.

Test burn:

Check wicking. Test burn the candle for burn pool diameter and “mushrooming” after it has cooled for 48 hours. Mushrooming is when carbon and/or other substances build up on the end of the wick interfering with combustion. Mushrooming can cause sooting and pour odours. Try different wicks until you have your desired burn pool diameter and a good clean flame. Every combination of mould, wax, dye, fragrance and wick must be tested for burn quality.

If you are not happy with your item please return it in the original packaging and with all relevant tags attached within 30 days. Goods must be returned carriage paid. Refund of the purchase price will be returned by the same method as the payment was made. Postage and packaging will not be refunded.

If your item is faulty or we have sent you something different to the product you ordered, again please return it to us within 30 days and we will give you a full refund or replacement, including postage and packaging.

We are absolutely committed to our customers - we value your feedback so please do get in touch.

LiveMoor supply high quality craft products at the best possible prices. We value customer service above all and will do our absolute best to give our customers the service they desire and deserve.

We are situated in a beautiful area on the southern edge of Dartmoor in Devon. Surrounded by rolling hills and open moorland, we work with farmers, bee-keepers, foragers and most importantly, nature.

We source products that fit in with a more natural way of life. We are constantly evaluating our products and processes to ensure that we can provide the highest quality at the best prices.

Please have a look around. If you can't see what you are looking for, do get in touch and we will do our best to find it for you.