Ps:

There are two colors of control board,red and blue,the colors are shipped randomly, and the functions are the same.

                                           100% Brand New and High Quality!!!

Nema23 Stepper motor 76mm/270Oz-in/ 3A 1.8Nm

General Specification:

• Step angle accuracy: ±5%(full step,not load)
• Resistance accuracy: ±10%
• Inductance accuracy: ±20%
• Temperature rise: 80deg Max(rated current,2 phase on)
• Ambient temperature ----------—20deg ~+50deg
• Insulation resistance:100MΩ Min,500VDC
• Insultion Strength--------500VAC for one minute

Wiring:

• A+ : Red
• A- : Green
• B+ : Yellow
• B- : Blue

TB6600 stepper motor driver 4.5A

Parameters:

• The working voltage is DC 10V-45V. It is recommended to use switching power supply DC32V for power supply.
• Adopt 6N137 high-speed optical lotus root to ensure high speed without losing step.
• Using Toshiba's new high-current, high-voltage TB6600HG brand new original chip, with low-voltage shutdown, overheating shutdown and over-current protection circuits, and short-circuit protection added compared to TB6560.
• The rated maximum output reaches: ±4.5A.
• Suitable for 42, 57, 86 two-phase/four-phase/four-wire/six-wire stepper motors within 4.2A.
• Automatic half-flow function.
• Subdivision: full step, half step, 1/4 step, 1/8 step, 1/16 step, maximum 16 subdivisions.

Description:

• The working voltage is DC 10-45V; it is recommended to use DV32V switching power supply.
• There are two input terminals, both of which adopt the common anode input mode.
• The level of the input pulse is 5V, if it is a 12V level pulse, a 1K resistor is required, if it is a 24V level pulse, a 2.4K resistor is required.
• The motor runs when the CLK has pulses, and automatically enters the set half-current state when there is no pulse, and the motor is locked.
• The motor rotates forward when CW is high or suspended, and reverses when it is low.
• When EN is high or floating, it is working state, when it is low, it is offline.

Note:

• The power supply cannot be connected reversely, otherwise the chip will be burnt out.
• The set current should not exceed the rated current of the motor.

Mach3 USB motion control board 4 axis

Notice:

• The motion control card for machine control, with strong professional.Requires the operator to have the relevant expertise!
• Please strictly follow the instructions and warnings before using this product
• If you are not familiar with the product and software features, make sure the machine's power switch on hand, you can quickly turn off the power.
• It is recommended that the limit switch and emergency stop switch must be installed first and can be used normally.

Features:

1. Support for 4-axis linkage, you can connect four stepper motor drives or servo drives;

2. Maximum step-pulse frequency is 100KHz,which is suitable for the servo or stepping motor;

3. 4 general-purpose opto-couplers isolation input : can connect the limit switch, emergency stop

switch, auto tool zero, home switch etc.

4. Support for connecting electronic handwheel;

5. Have 0-10V signal output , you can use mach3 software to control the spindle motor speed.

6. 4 general-purpose isolated relay drive output interface, can drive four relays for controlling

the spindle starts, forward rotating and reverse rotating, pumps or other device;

7. 1 status LED, indicate connection status on the board

 

350W 24V DC switching power supply

Specification:

• DC output: 24V 0-14.5A
• Inlet stability: ±0.5%
• Load stability: ±0.5%
• DC voltage of Adjustable range: ±10%
• AC input voltage range: 115VAC/6.5A/50HZ----230VAC/3.4A/60HZ; Selected by switch
• Overload protection: 105%-135% cut off the output, automatic recovery
• Over-voltage Protection: 115%-150% shut down O/P voltage, re-power on to recover
• Setup/rise/hold-up time: 200ms、50ms、20ms/230VAC at full load
• Withstand voltage: I/P-O/P: 1.5KvAC; I/P-FG: 1.5KvAC; O/P-FG: 1.5KvAC; 1minute
• Isolation resistance: I/P-O/P、 I/P-FG、O/P-FG: 500VDC/100MΩ
• Working Temperature: -10℃～+50℃