Features:
1. Use of high quality materials, durable
2. All use screwdriver-free potentiometer, can be directly manually adjusted
3. Chip to strengthen heat dissipation, reliable and stable, high power
4. Real-time display of MPPT adjustment voltage, easy to understand at a glance
5. Wide range of use, solar charging, battery lithium charging, LED
Constant current driver, voltage regulator
1. Use of high quality materials, durable
2. All use screwdriver-free potentiometer, can be directly manually adjusted
3. Chip to strengthen heat dissipation, reliable and stable, high power
4. Real-time display of MPPT adjustment voltage, easy to understand at a glance
5. Wide range of use, solar charging, battery lithium charging, LED
Constant current driver, voltage regulator
Parameters:
Input voltage range: DC7-80V
Output voltage range: DC1.4-79V
Voltage display range: 1.40-80.00V (accuracy +0.1V or so)
Output current adjustment range: 0-20A
Current display range: 0.00A-20.00A (accuracy +0.03A approx.)
Adjustment knob: MPPT voltage adjustment, output voltage adjustment, output
Current limit adjustment
MPPT function: Yes
Anti-backflow: battery backflow will not burn, when the sun is not enough without charging current
There will be 0.5-40mA backflow current, it is recommended to connect the diode when charging.
Constant current (current limiting): Yes
Over power protection: 300W, over power will shut down the output, display 0PP
Size: 108x64x48mm
Input voltage range: DC7-80V
Output voltage range: DC1.4-79V
Voltage display range: 1.40-80.00V (accuracy +0.1V or so)
Output current adjustment range: 0-20A
Current display range: 0.00A-20.00A (accuracy +0.03A approx.)
Adjustment knob: MPPT voltage adjustment, output voltage adjustment, output
Current limit adjustment
MPPT function: Yes
Anti-backflow: battery backflow will not burn, when the sun is not enough without charging current
There will be 0.5-40mA backflow current, it is recommended to connect the diode when charging.
Constant current (current limiting): Yes
Over power protection: 300W, over power will shut down the output, display 0PP
Size: 108x64x48mm
Solar cell charging steps.
1. Measure solar panel no-load voltage ( sunny), calculate MPPT voltage =
0.75*no-load voltage, or look directly at the manufacturer's panel Vmp parameter value.
Note that the positive and negative poles should not be connected backwards.
1. Measure solar panel no-load voltage ( sunny), calculate MPPT voltage =
0.75*no-load voltage, or look directly at the manufacturer's panel Vmp parameter value.
Note that the positive and negative poles should not be connected backwards.
2. Connect the solar panel to the module power supply, switch to the display MPPT voltage interface, adjust the
Turn the MPPT potentiometer and adjust the value to the Vmp voltage.
Turn the MPPT potentiometer and adjust the value to the Vmp voltage.
3. Turn the CV potentiometer to adjust the output voltage (the size is the floating charge of the battery being charged).
The output voltage is adjusted by rotating the CV potentiometer (to the floating charge of the battery being charged).
The output voltage is adjusted by rotating the CV potentiometer (to the floating charge of the battery being charged).
4. Short the positive and negative output terminals and turn the CC potentiometer to adjust the current limit (the size is the allowable charge voltage of the battery being charged).
4. Short the output terminals, turn the CC potentiometer and adjust the current limit (the size is the allowable charging current of the battery being charged).
If the solar panel power is too small, the MPPT lamp will light up when short-circuiting, in order to keep the input voltage constant.
The output current will be limited in order to maintain a constant input voltage, the current can only be adjusted downwards and the MPPT
The current value seen when the MPPT light is off is the only one that makes sense.
It is recommended that the current is adjusted when there is sufficient sunlight or when a constant voltage source is used as input.
4. Short the output terminals, turn the CC potentiometer and adjust the current limit (the size is the allowable charging current of the battery being charged).
If the solar panel power is too small, the MPPT lamp will light up when short-circuiting, in order to keep the input voltage constant.
The output current will be limited in order to maintain a constant input voltage, the current can only be adjusted downwards and the MPPT
The current value seen when the MPPT light is off is the only one that makes sense.
It is recommended that the current is adjusted when there is sufficient sunlight or when a constant voltage source is used as input.
5. Connect the battery for charging (be careful not to reverse the positive and negative terminals). The MPPT can be adjusted appropriately
potentiometer, so that the module is always at the maximum power point output.
It is recommended to connect a diode to completely prevent backflow.
potentiometer, so that the module is always at the maximum power point output.
It is recommended to connect a diode to completely prevent backflow.
Notes and reminders:
1. the positive and negative input terminals must not be reversed, otherwise they will burn up.
2. When the output is connected to the battery, the positive and negative poles cannot be reversed, otherwise it will burn.
3. The maximum output current of 20A is limited to the time when the voltage difference between the input and output voltage is small.
And the output power should not exceed 300W.
The greater the difference between input and output voltage, the lower the conversion efficiency and the more serious the heat generation.
If the heat is too serious, please reduce the power to use, or add 5V fan by yourself (with reserved
The fan current is less than 300mA) to assist in heat dissipation.
4. MPPT voltage - generally set to 0.75 times the open circuit voltage of the solar panel, also
You can read the nameplate or consult the solar panel manufacturer for the Vmp voltage value.
is the MPPT voltage we want to set. The display shows the set voltage.
It is very easy to adjust at a glance.
The output current limit (CC) value is the allowable charging current of the rechargeable battery.
The current is set by: short-circuiting the output directly with a wire and looking at the current display.
Adjust the CC potentiometer, the displayed value is the current limit value (maximum output current value).
1. the positive and negative input terminals must not be reversed, otherwise they will burn up.
2. When the output is connected to the battery, the positive and negative poles cannot be reversed, otherwise it will burn.
3. The maximum output current of 20A is limited to the time when the voltage difference between the input and output voltage is small.
And the output power should not exceed 300W.
The greater the difference between input and output voltage, the lower the conversion efficiency and the more serious the heat generation.
If the heat is too serious, please reduce the power to use, or add 5V fan by yourself (with reserved
The fan current is less than 300mA) to assist in heat dissipation.
4. MPPT voltage - generally set to 0.75 times the open circuit voltage of the solar panel, also
You can read the nameplate or consult the solar panel manufacturer for the Vmp voltage value.
is the MPPT voltage we want to set. The display shows the set voltage.
It is very easy to adjust at a glance.
The output current limit (CC) value is the allowable charging current of the rechargeable battery.
The current is set by: short-circuiting the output directly with a wire and looking at the current display.
Adjust the CC potentiometer, the displayed value is the current limit value (maximum output current value).
Package list:
Step-up and step-down power supply module*1
Step-up and step-down power supply module*1
Am 17.11.2022 hat der Verkäufer die folgenden Angaben hinzugefügt: