|
Long Range Underground Diamond Metal Detector Gold
Treasure Hunter
EPX10000 Long Range Underground Metal Detector with degausser Eliminate
interference signals
Item specificsDetection depth range:5-50m
Detection distance range :100-1000m
Rechargeable battery:8 hours of continuous work
Voltage:12VDC
The temperature range:45℃ to 85℃
Humidity:0~95%(non condensing)
16 bit processor speed,40MIPS –16MHz
32 bit DSS synthesis chip,wave from output
Digital frequency synthesisX20PLL,automatic frequency stabilizer,0.1MHz
Color LCD display,a resolution of 480 x 320 pixels
Net weight:6.6kg,Gross weight:10.5kg
Product size:47X37X13.5cm
1.Radar Scans LED Panel
2.Signal transmission
3.Select the metal type
4.Depth adjustment
5.Range adjustment
6.Receiving antenna
Scanner control installation
Note: Before the daily operation, the battery must be fully charged! If you do not charge it, the EPX10000 might go wrong. If abnormal , this may be the first time warning that the battery power is too low and must be charged. If the battery power is charged a whole night, after that, the battery is still no power, you need to replace the battery or charger, or AC power outlet without electricity. If the battery is charged,but it is not full of power,you may need to replace the built-in battery. A new fully charged battery can let EPX10000 continue to work about eight hours.
Before turning on the scanner, put the EPX10000 transmitter on the ground, the sensor antenna is connected to the corresponding jacks of the transmitter. When open the transmitter,never plug the sensor, if doing it, it will cause damage to the machine.
Previously used EPX10000 scan,first make all the necessary connections.
1.The sensor is connected to the scanner testing (+) testing (-) on the jack, insert the probe of sensor on the earth
2.The transmit antenna signal transmission is mounted on the corresponding interface
3. with the power key is turned "On / Off” knob, turn on the power. At this time, in the LCD area, power indicator,horizontal trmming,longitudinal trmming indicator lights.
4. at this time, EPX10000 is scanning all selected element . Before starting the detection process, please let it work 3-5 minutes, which will be briefly explained later.
5.after the end of the operation, remember to turn off EPX10000. For ease to use,the instrument requires the use of a smll battery charger is connected to the power line charg instrument.
Receiver - The rotary switch on the top of the receiver panel are the headphone and the antenna jack. When do not use, do not connect the antenna rods with the receiver! If the antenna rod is saved with it inserted in the receiver , it will cause the battery to drain.
Receiving antenna rod - rod antenna is designed to point out to the operator that he / she has entered a power transmission line between the sensor and the target. Under normal circumstances, the operator should hand held the antenna rod stably and balanced, as high as your waist, and slightly in front of the operator. When hand held the antenna rods, rod antenna should is pointed to the front and parallel to each other and separated by 8-18 inches away. Everyone needs to find their own best distance. It takes trial and error to find. Please remember, the people who operate this device, calm relaxed person will do better than the tense stiff! When you enter the RF energy line, measured metal,the antenna rod will naturally cross.
And the radar scan pointer will stop in one location. When the antenna and radar cross and the scanner pause, you see the dawn of victory would come.
The key point is that how to hold the molecular frequency detector receiver rods , as well as body position and walk.
Users must stand in a relaxed posture, feet slightly apart, arms close to the body but not too tight. When holding the receiver rod , the palms and wrists should not be too hard to make it in the hands automatically reach balance, and always parallel to each other. When hand holding the rod, let it be parallel with the ground, in order to increase their sensitivity, or slightly down incline 5-8 °, achieve a better balance (if you are a novice of molecular frequency detector).
The most important thing is the way to practice holding the rod, the rod until the two are no longer mutually "away."
After the balance of the receiver rods is completed, the operator should learn how to walk, step by step, while maintaining a balance of two rods. This is another trial and error: the pace must be maintained at normal speed, firm and uniform. Each step across the same distance, otherwise the two will be out of balance. Shrugging will lead two out of balance. Shoulders should be maintained at the same height.
Try to practice and keep these conditions.
The holding of receiving rod, posture and walking exercises should follow the requirements of the target test, the operator should test the target object on the ground to observe the reaction of the receiving rod.
Once the "Scan Start " message appears on the screen, beginning at a distance of 3 meters at EPX10000 detector loop around, keep the receiving rod be in balance and insert the power module.
If the target object exist, when we walk in the transmission line of the target object and EPX10000 on the ground between them, two receiver antenna will be completely crossed. At such moment,the two shots parallel distance is 15cm. We can double-check to determine whether it is stable signal. So that the operator needs to return to relax, moving again to the transmission line. If the receiving rod is crossed every time, then we can track the target signal in Example 2 in accordance with a signal trace diagram. When the operator through the buried objects will be no crossing. The target objects is located in the point which is between the two rods last crossing and two rods no crossing.Metal detectors can be used to accurately position the target object. Referring to our example, continue to practice in order to achieve better results.
SCANMASTER Research Center spent years testing various theories, ideas and devices, developed this EPX10000 transmission at last,it is small, powerful, long-distance transmission through soil frequency (RF) signals. 360°comprehensive import signal emitted by the soil. It is because of the inductive energy ,the target can be detected.
Signal emitted by the scanner power sensor into the ground. If the target is within the range you are looking for, then the signal is absorbed by the target. Indicator rod is inserted into the power amplifier, the receiver circuit becomes complete. The circuit through the operator's body capacitance and inductance components of the power module is formed. When the operator to walk through the transmission line between the scanner and the target, the circuit will play an active role. The RF transmission line inductance and the circuit inductance, capacitance of the operator's is interacted. At this time, the normal reaction is the rods attract each other. This is actually convey information to the operator: the target is within range of the scanner.
The scanner's range how far and how depth it is,it depends on a number of change factors. The first foremost and the most important variable is the target size and then the soil conditions (presence of electrolytes) and how long the target has been underground. Another factor is the chemical changes in the soil around the target, the factors that can enhance the scanner's operating performance. The target is susceptible to oxidation, no matter itself or its container object, the signal will be issued more. The factors due to oxidation, the target of the transmission signal amplified potential to the scanner will be greater.
There are target within the range, when your feet start into the energy line, under normal circumstances, the antenna rods will attract each other. Under normal circumstances, a single target,the width of energy line is 20 inches.
Once confirm the energy line, the next step is to use S-line measurement method or a triangulation method to detect the target.
When a person want to make sure the target position in water , cliffs and other inaccessible (eg, lakes or streams) place, the scanner is as easy as operating it on the ground. Remember the most important thing is that the operator must be able to enter between the target and the power sensor, so that the antenna rods can indicate any potential targets. Obviously, you can not take the antenna rods underwater. The best way is to speculate, as well as from the shore or on board measuring the target by triangulation, apply some basic knowledge of geometry.
When operating from the shore, first look inside the scanner if there is any objective measurement range. If something there or not, the first step is moving the scanner, which is the easiest step to operate (north, south, east or west) on four main compass orientation in an orientation. The second record should be 45 °angle between the first record. For example, if the first reading at the target location due west direction, the second reading position in the positive direction of the northwest or the positive direction of the southwest Referring to the figure below.
Please note that due west at the position # 1 is in the west of target. The position # 2 is located on southwest of the target. Considering this situation, we finally have two 45 ° angles and a 90 ° angle. Thus, from the position # 1 to position # 2 is equal to the distance between the distance from the position of a target. As a result, you have to measure the target using the triangulation method, now know the distance from the position # 1 to the target.
From the ship's operator, the operator, it has some interesting challenges. The first challenge is the deck size. The operator must be able to have a power sensor for the center is about 5'-10 'radius. Second, the probe must be in contact with the power sensor vessel deck. To solve this problem, use a wet towel wrapped around the probe, wet towel in contact with the deck. RF energy along the target direction and the deck surface. Need the buoys, in order to help detect the target by triangulation. With the rest of the process is very similar to the first method.
EPX10000 almost no maintenance. Receiving rods is corroded by salt and water in the environmental , it is required to use the good quality brass to clean regularly to ensure that the appearance and performance intact.
CONCLUSION
If you are an experienced treasure hunter, you already know at this time, EPX10000 and the traditional targeting methods are completely different. Scanning in a given area and directions or locate possible goals, EPX10000 is very fast. EPX10000 absorbs the signal underground from the sensor to the target . If there are multiple targets of the same element in a given direction, the maximum target is absorbing the signal transmission. If you remove the larger goal, you can track smaller targets.
If you search for large deposits, such as veins, let the antenna rods in the open scanner can begin work immediately. Open the scanner, check the area immediately. Should not wait too long, because of the smaller veins absorption signal will start, but the absorption amount is small. If this occurs, the short turn off the scanner in a short time(e.g., 15-30 minutes), so that the signals disappear. Then, turn on the scanner again, immediately it is marked through live goal line. The EPX10000 is moved to a new location in order to detect the target by triangulation, as follows:
Remember, first,if your local soil strata with high gold content , the transmitter is opened longer, you receive the signal line will be more. Second, whether it is gold powder or in blocks, all gold,gold and gold belong to different substances. Must remember that you are using the frequency of the electromagnetic spectrum, all frequencies will be involved. Finally, the frequency of mutual interference may occur. Therefore, it should be noted in the actual operation.
SUMMARY
We have been researching and developing EPX from the 1960s. In 2014,we promote our latest generation of EPX10000. We know it really working well. There are very few people using the scanner during the initial encounter some difficulties. Before purchasing, usually demonstrate to customers to experience the feeling of hands-on instruction bar. We must remember that the human body is actually the antenna, the power module is a part of the circuit needs adjusting. Without the body (antenna), indicating rods can not work. Without power module, you can splash water (not everyone can splash). For new and old customers we repeatedly say the words, "You have to practice, practice, practice ......, nothing can replace practice."
Browser security identification
For EPX10000 scanner, the initial purchaser can enjoy 12 months free warranty. For the convenience of our statistical real sales data, if the current owners to provide the original sales receipts, will also enjoy the warranty service. Please note, packaging, collection, sensors, power modules, and a pointing stick and enjoy the date of purchase date 90 days free warranty. For damage due to negligence instruments, repair charges will be the market price. All equipment in need of repair, must be sent to the shipping to us, then return to you,the freight is paid by customer.Unless other agreement. We are not responsible for customs duties and other charges arising by clients.
|