Autel PowerScan PS100---Revolutionary Circuit Tester

Autel PowerScan PS100 Tool is the most revolutionary circuit tester to date. Featuring AVOmeter, test light, built-in flashlight, short circuit indicator, relay/ component tester, continuity tester and bad ground indicator, the PowerScan 100 is truly the ultimate in power and affordability, allowing users to check circuitry in one single step.

Autel PS100 Car Circuit System Diagnostic Tool can quickly and accurately diagnose the electrical system, solve problems such as circuit short circuit, open circuit, etc., which is an essential circuit scanner for every technician.

Autel PS100 Circuit Tester Kit--- Do Everything For You

 

• DC voltage range : 0-65V +1 digit; Resistance range : 0–200 KΩ; Frequency response of tone passage: 0Hz to 10Khz.
• Performs multi-service including power injection, measurement, ground testing, polarity checks, continuity testing and components activation
• Easy to read AVOmeter allows you to read voltage, current and resistance at the fingertip
• Component activation with a flip of the power switch,
• Instantly identifies positive, negative and open circuits
• Test bad ground contacts instantly, allowing you to follow and locate shorts fast without wasting fuses
• Instantly checks continuity of switches, relays and diodes
• Circuit breaker protected
• Extra 20ft (extendable) cable provides excellent accessibility to test along the vehicle
• Built-in Flashlight, work in the dark
• Simple button design

 

More Useful Features, Give You Try

Autel PowerScan PS100 has rich functions, please check the following introduction:

 

1. 4 modes to diagnose the electrical system: DC voltage, AC voltage, resistance, diode.
2. Voltage & Polarity Test: According to the LED light and sound after the probe tip touches the circuit, it can accurately judge the positive, negative, and open circuits.
3. Continuity Test: While the tool is in Resistance mode, using the probe tip with chassis ground or the auxiliary ground lead, continuity can be tested on wires and components attached or disconnected from the vehicle’s electrical system.
4. Signal Circuit Test: When the vehicle has a fault code, in order to quickly determine whether the fault is caused by a certain sensor circuit, you can use this tool to quickly draw a conclusion.
5. Find Short Circuit: A short can manifest itself as a blown fuse or a tripped electrical protection device. Use the probe tip to activate and energize each fuse contact. The contacts that trip the circuit breaker are shorted.
6. Find Bad Ground: Probe for suspected ground wires or touch probe tips. If the breaker has tripped, the circuit is most likely grounded.
7. Activate Component in your hand/ in the vehicle/ W/Ground
8. Test Trailer Lights and Connections: Check function and orientation of connectors and trailer lights
9. Red/Green Polarity Indicator: The red/green polarity LED illuminates when the probe tip voltage matches and is within ±0.8 volts of the battery voltage. It is additional information that may be of value to a technician.

 

Extra 20ft Extension Cable

20ft Extension Cable:

 

• Autel PS100 itself has an extra-long cable, but considering the volume of 12V-24v vehicles such as ships and trucks, we have additionally equipped with extra 20FT extension cable for emergencies.
• With the 20FT extension cable, you can freely test the condition of any vehicle circuit without moving the device because the cable is not long enough.

 

Autel PS100 Circuit Tester has two power supply methods:

 

• 1. Vehicle battery power supply
• 2. Ciga-rette li-ghter power supply

 

Quick Self-Test:

 

• Before you test a circuit or component, be sure your tool is in good order by doing a quick self-test.
• With the tool connected, perform a quick self-test. The power switch is a momentary rocker switch located on the tool's body. Flanking the switch are positive and negative markings. Press the Power Switch forward to activate the tip with a positive voltage. The Red LED should light and the LCD display will read the battery voltage. If the tone feature is turned on, a high pitched tone will sound. Let go of the power switch and the LED will turn off and the high tone will cease. Press the Power Switch rearward to activate the tip with a negative voltage. The Green LED should light and the LCD display will read the „0.0V‟ (ground). If the tone feature is turned on, a low pitched tone will sound. Let go of the power switch and the LED will turn off and the low tone will cease. Your tool is working correctly and is now ready for use.

 

Test Tool Specifications