KINGBOLEN S800 Service for:

Technician , advacne DIY, garage, car dealer, used car dealer, auto repair shop, automotive engineer, diagnostic tech, truck man, automobile tech, home mechanic, DIY beginner, automotive student, backyard mechanic, retired mechanic, weekend DIY, individual.

What we did on KINGBOLEN S800 OBD2 Scanner to make it more perfect in 2023?

KINGBOLEN S800 Supports 4 Systems Diagnosis and 15 Special Reset Functions

• For Engine System: Easily determine the cause of the Engine System, and turn off the warning light. Guides you to find out problems in engine, check its real-time operating status, and turn off warning light for making sure engine work properly and safely.

• For Transmission: It can figure problems out via reading codes in the Transmission system, or check the health status via live data viewing.

• For ABS System: Read and clear DTCs data flow in the ABS system. Performs various bi-directional tests to check the operating conditions of Anti-lock Braking System, and turn off the warning light. It retrieves ABS codes to tell you where the problem is with a visual inspection of all brake components.

• For SRS System: Read and clear fault code in SRS (Airbag) system and turn off warning light of airbag for making sure engine work properly and safely. This diagnostic tool allows you to read codes, clear codes, and read live data in Supplementary Restraint System (airbag) to ensure it works fine.

1.Oil Reset:The lightening of the car maintenance light indicates that the vehicle needs maintenance Reset the mileage or driving time to zero after the maintenance.

2.Electronic Throttle Sensor Reset：Throttle Adaption is to utilize the car decoder to initialize the throttle actuator so that the learning value of the ECU returns to the initial state. By doing these, the movement of the throttle (or idle motor) can be more accurately controlled, thus adjust the intake volume. Situations when throttle matching is needed:

a)After replacing the electronic control unit, the relevant characteristics of the throttle

operation have not been stored in the electronic control unit.

b)After the electric control unit is powered off, the memory of the electric control unit's

memory is lost.

c)After replacing the throttle assembly, you need to match the throttle.

d)After replacing or disassembling the intake port, the controlling of the idle speed by the

coordination between the electronic control unit and the throttle body is affected.

)Although the characteristics of the idle throttle potentiometer have not changed, the

intake volume has changed and the idle control characteristics have changed at the

same throttle openings.

3.Brake-pad Reset: To deactivating and activate the brake control systems, assist with brake fluid control, open and close brake pads, and set brakes after disc or pad replacement

If the brake pad wears the brake pad sense line, the brake pad sense line sends a signal

sense line to the on-board computer to replace the brake pad. After replacing the brake

pad, you must reset the brake pad. Otherwise, the car alarms.

4.TPMS Reset:When due to the tire pressure is too low,tire leaks,tire pressure monitoring device is replaced or installed,tire is replaced and  tire pressure sensor is damaged,The tire pressure

resetting function must be performed to reset tire pressure and turn off the tire pressure.

5.SAS Reset: It helps clear the faulty steering angle sensor memories to reset the steering angle and plays an important role in the steering angle sensor calibration.

6.Battery Matching:Enables you to perform resetting operation on the monitoring unit of battery,in which the original low battery fault information will be cleared.

7.DPF Regeneration:It is used to clear PM (Particulate Matter) from the DPF filter through continuous combustion oxidation mode. Specially works for Diesel Particulate Filter system with DPF.

8.ABS Bleeding:When the ABS contains air, the ABS bleeding function must be performed to bleed the brake system to restore ABS brake sensitivity.

9.Gearbox Matching:This function can complete the gearbox self learning to improve gear shifting quality

10.EGR Adaption:This function is used to learn the EGR (Exhaust Gas Recirculation ) valve after it is clean or replaced.

11.AFS Reset:It is used to initialize the adaptive headlamp system.

12.IMMO Service:To prevent the car being used by unauthorized keys, the anti-theft key matching function must be performed so that the immobilizer control system on the car identifies and authorizes remote control keys to normally use the car.

13.Suspension Matching: When replacing the body height sensor in the air suspension system, or control module or when the vehicle level is incorrect, this function can adjust the body height sensor for level calibration.

14.Injector Coding:After the ECU or injector is replaced, injector code of each cylinder must be confirmed or re-coded so that the cylinder can better identify injectors to accurately control fuel injection.

15.Sunroof Initialization:This function can set the sunroof lock off, closed when it rains, sliding / tilting sunroof memory function, temperature threshold outside the car etc.