M16 Throughbolts ZYP Heavy Duty Masonry Concrete Anchor

M16, Throughbolts, ZYP, Heavy Duty, Masonry Anchor - All Lengths. Fixaball sells all lengths of M16 throughbolts, in zinc. Advantages of a Throughbolt High Performance, cost effective anchor for non-cracked substrates eg. concrete Suitable for reduced embedment to avoid contact with rebars/ reinforcement cages. Holes are the same diameter as the fixings so the fixing can be passed through the fixture after locating it in the right position. Cold formed body provides consistent dimensional accuracy and material stability High load-bearing capacity Throughbolt, expansion, masonry anchors are used for fixing materials to non-cracked concrete/ masonry (brick/ blocks), and non-porous stone. Orders placed before 2pm are dispatched same day (Mon-Fri). Standard, Free Delivery is Royal Mail, 2nd Class (2-5 days, most likely 2 days). For a faster delivery time, select 1st class or courier at checkout. Please make your 'no of items in pack', 'length', and 'quantity', of packs selection from the drop down menus. M16 Throughbolt Lengths Available Anchor Hole Size Anchor Length 16mm 105mm 16mm 125mm 16mm 150mm 16mm 175mm 16mm 220mm Table to show important installation settings/ measurements: All measurements in mm Size Anchor Fixture Diameter Length Max. Thickness Hole Diameter M16 16 100 5 - 18 105 10 - 125 25 5 140 40 20 150 50 30 160 60 40 180 80 60 220 120 100 280 180 160 Installation and Advice Before installation, check the concrete’s strength in order to make sure its class/ standard is suitable. The concrete base must be compact and porosity insignificant. Installation temperature range for base material: -5 / + 40 ºC (80 ºC for a short period of time). Minimum installation depth values must always be respected: for anchors’ depth, for anchor-to-anchor distances and for anchor-to-edge distances. Drilling must be performed by respecting the specified minimum depth and diameter, perpendicular to the base material’s surface. The holes on the material to be fixed may be used as templates. When drilling near any reinforcement areas, special care must be taken to avoid damaging them. If drilling is aborted because a reinforcement area has been encountered, it is advisable to drill a new hole at a minimum distance of at least twice the aborted drill hole diameter. This advisable distance may be reduced, as long as the aborted hole is previously filled up with high-resistant mortar. It is necessary to clean the holes thoroughly free of dust and debris with a suitably sized brush. When temperature is below 0ºC, make sure water does not seep into the hole, as this fact could cause subsequent cracks on the concrete, due to ice pressure. Introduce the anchor through the material to be fixed into the hole up to the embedment depth, according to the values on the table. It is possible to use a hammer to ensure the required depth. Do not apply any intermediate layer between the material to be fixed and the washer, such as sealing products. Apply the specified torque with a torque wrench. In the case the holes on the material to be fixed have a bigger diameter than required, it is necessary to insert a thicker washer and of a bigger diameter. But please, note that this procedure does not ensure a correct distribution of shear loads amongst all the anchors of a same group, and this shear load is applied only to the anchors with a correct diameter on the material to be fixed. Image is for illustrative purposes only.

M16 Throughbolts ZYP Heavy Duty Masonry Concrete Anchor

M16, Throughbolts, ZYP, Heavy Duty, Masonry Anchor - All Lengths.

Fixaball sells all lengths of M16 throughbolts, in zinc.

Advantages of a Throughbolt

  • High Performance, cost effective anchor for non-cracked substrates eg. concrete
  • Suitable for reduced embedment to avoid contact with rebars/ reinforcement cages.
  • Holes are the same diameter as the fixings so the fixing can be passed through the fixture after locating it in the right position.
  • Cold formed body provides consistent dimensional accuracy and material stability
  • High load-bearing capacity

Throughbolt, expansion, masonry anchors are uséd for fixing materials to non-cracked concrete/ masonry (brick/ blocks), and non-porous stone.

 

Orders placed before 2pm are dispatched same day (Mon-Fri).

Standard, Free Delivery is Royal Mail, 2nd Class (2-5 days, most likely 2 days). For a faster delivery time, select 1st class or courier at checkout. 

Please make your 'no of items in pack', 'length', and 'quantity', of packs selection from the drop down menus.

M16 Throughbolt Lengths Available

Anchor Hole Size Anchor Length
16mm 105mm
16mm 125mm
16mm 150mm
16mm 175mm
16mm 220mm

 

Table to show important installation settings/ measurements:

All measurements in mm

Size

 

Anchor

Fixture

Diameter

Length

Max. Thickness

Hole Diameter

M16

16

100

5

-

18

105

10

-

125

25

5

140

40

20

150

50

30

160

60

40

180

80

60

220

120

100

280

180

160

 

Installation and Advice

  • Before installation, check the concrete’s strength in order to make sure its class/ standard is suitable.
  • The concrete base must be compact and porosity insignificant.
  • Installation temperature range for base material: -5 / + 40 ºC (80 ºC for a short
  • period of time).
  • Minimum installation depth values must always be respected: for anchors’ depth, for anchor-to-anchor distances and for anchor-to-edge distances.
  • Drilling must be performed by respecting the specified minimum depth and diameter, perpendicular to the base material’s surface. The holes on the material to be fixed may be uséd as templates.
  • When drilling near any reinforcement areas, special care must be taken to avoid damaging them. If drilling is aborted because a reinforcement area has been encountered, it is advisable to drill a new hole at a minimum distance of at least twice the aborted drill hole diameter. This advisable distance may be reduced, as long as the aborted hole is previously filled up with high-resistant mortar.
  • It is necessary to clean the holes thoroughly free of dust and debris with a suitably sized brush.
  • When temperature is below 0ºC, make sure water does not seep into the hole, as this fact could cause subsequent cracks on the concrete, due to ice pressure.
  • Introduce the anchor through the material to be fixed into the hole up to the embedment depth, according to the values on the table. It is possible to use a hammer to ensure the required depth. Do not apply any intermediate layer between the material to be fixed and the washer, such as sealing products.
  • Apply the specified torque with a torque wrench.
  • In the case the holes on the material to be fixed have a bigger diameter than required, it is necessary to insert a thicker washer and of a bigger diameter. But please, note that this procedure does not ensure a correct distribution of shear loads amongst all the anchors of a same group, and this shear load is applied only to the anchors with a correct diameter on the material to be fixed.

Image is for illustrative purposes only.

×
×
×
×
×
×
×

Tell a friend Visit store Watch now

Postage info

Click the Postage tab above the listing description for more info

Additional delivery notes

PICK UP OPTION

Sorry, our items are NOT available for pick-up.

PAYING VIA PAYPAL


We accept PayPal on our all our items so you can shop with confidence.

Simple choose the PayPal option when proceeding through the checkout.

Additional Information

No additional information at this time

Ask seller a question

To contact our Customer Service Team, simply click the button here and our Customer Service team will be happy to assist.

Ask seller a question

© Fixaball

Click the Postage tab above the listing description for more info

Accepted Payment Methods

  • PayPal

Returns are accepted

Items must be returned within 30 days of the auction ending

Buyer will pay for return shipping.


Additional Information:
Returns 'NO QUIBBLE' Our returns policy lasts 30 days. If 30 days have gone by since delivery, unfortunately we can’t offer you a refund or exchange (+ a couple of days, grace). To be eligible for a return, your item must be unuséd and in the same condition that you received it. It must also be in the original packaging with original documentation. A restocking fee of 15% will be applied to refunds. Cost of sending the shipment is not refunded unless the wrong item was sent. To complete your return, we require a receipt, invoice or other proof of purchase. This will enable an easier process of locating and amending orders. Please keep all labels, stickers and original packaging to be eligible for free returns. Refunds (if applicable) NO QUIBBLE - We invite all people to stay with us as their preferred supplier of fixings and fasteners. If you're not happy, we will do everything possible to help. Please, please, please keep all documents, stickers, labels and packaging; it makes the process run quicker and easier. Orders over £1000 need to be returned within 5 working days to be accepted, processed and refunded. Late or missing refunds (if applicable) If you haven’t received a refund on the day of return please contact us to verify the situation. Banks vary in their reaction time to changes; there is often some processing time before a refund is posted. Any concerns no matter how small, contact: 01242 522244 Sale items (if applicable) Only regular priced items may be refunded, unfortunately sale items cannot be refunded. Exchanges (if applicable) NO QUIBBLE - All exchanges are welcomed, assuming that items are suitable for re-sale. Please, return the item with the invoice and a note describing what you would like as an exchange. AN invoice will be sent to cover the postage to send the exchanged item. Free returns are available in the very rare event that we have sent an incorrect item. Orders over £1000 need to be returned within 5 working days to be accepted, processed and exchanged. Shipping 99% of orders are dispatched the same day as purchase if the order was made before 2pm. After 2pm your order will join the following days post. Royal Mail deliver most items up to 2kgs and Interlink Express deliver our oversized and heavier items, next day. Usually, the easy bit is getting the order out the door, but, what happens after can occasionally disappoint us both. If delivery is crucial/ time sensitive, you should select a faster and/ or signed for postage option at checkout. Mailing Disclaimer 98% (490 orders) of shipping arrives on time. 2% (10 orders) are late 1.4% (7 orders) 1 day late 0.4% (2 orders) 2 days late 0.2% (1 order) 3+ days late 0.01% is reported lost. - 1 every couple of years Our 'NO QUIBBLE' guarantee gives you peace of mind that we will accept all, undamaged returns and issue a refund, every time. If you need a definite arrival time please select an express service at check out to avoid disappointment.