1 pcs New Punch Cumulative Total Of Electronic Digital Counter TT-5J XJ-J Suit High Quality Brand New
Technical parameters:
Power: 1.5V - AA AA batteries
Cleared by: Panel / external
Count range: 0 --- 99999
Clearing the minimum pulse width: 0.1 seconds
Counting the highest frequency: 20HZ
Ambient temperature: -5--40 ℃
Count minimum pulse width: 10mS
Dimensions: 64 * 38 * 38 mm
The maximum contact resistance turned: ≤ 10KΩ
Hole Size: 61 * 36 mm
Disconnect the minimum contact resistance: ≥ 500KΩ
Weight: about 50 grams
Install the battery:
Be sure to install the battery after use! !
Unscrew the two screws securing the housing, gently separate the back cover (be careful not to pull off the signal line), into a 5 batteries (sold separately), close
the cover and tighten the screws back two shell.
Wiring methods:
Count signal input switch (sold separately): You can choose Our magnetic proximity switch: VJ12-D10K,
You can also choose other types of switches according to the actual situation, such as: micro-switches, limit switches, and so on.
Clear input switch: You can take an ordinary button, if cleared by the panel to select RESET, you can not answer.
How to use:
Start counting: counting terminal input contact signal, the counter starts counting.
Pause Count: Press count / Pause (PAUSE), suspended from counting; then click counts / Pause (PAUSE), resumes its count.
Panel clears: simply press the Delete key (RESET).
External clear: Clear terminal external contacts connected directly cleared.
Note:
1. the counter clear signal input signals and switch or circuit should be as close to the terminals of the counter, the signal lines as short as possible.
2. Avoid contact with others, such as: strong electrical wires or power wires, etc. with the tube or stranded traces to avoid unnecessary interference, if necessary,
use shielded cable, shield connected to the terminal + count on.
3. count signal and the clear signal input contact signal only, can not enter the other signals.
4. contact input should be reliable to avoid contact bounce caused by incorrect counting error is cleared.
5. When the LCD display fuzzy, replace the batteries with new ones. When a long time, remove the batteries to prevent battery leakage and damage deterioration counter,
remove the battery, and press the count / Pause (PAUSE), so that the screen display disappears, to close the counter inside the auxiliary battery.
Package:1 pcs digital counter + magnetic proximity switch + plastic round strong magnet + proximity switch mounting bracket in a package
Technical parameters:
Power: 1.5V - AA AA batteries
Cleared by: Panel / external
Count range: 0 --- 99999
Clearing the minimum pulse width: 0.1 seconds
Counting the highest frequency: 20HZ
Ambient temperature: -5--40 ℃
Count minimum pulse width: 10mS
Dimensions: 64 * 38 * 38 mm
The maximum contact resistance turned: ≤ 10KΩ
Hole Size: 61 * 36 mm
Disconnect the minimum contact resistance: ≥ 500KΩ
Weight: about 50 grams
Install the battery:
Be sure to install the battery after use! !
Unscrew the two screws securing the housing, gently separate the back cover (be careful not to pull off the signal line), into a 5 batteries (sold separately), close
the cover and tighten the screws back two shell.
Wiring methods:
Count signal input switch (sold separately): You can choose Our magnetic proximity switch: VJ12-D10K,
You can also choose other types of switches according to the actual situation, such as: micro-switches, limit switches, and so on.
Clear input switch: You can take an ordinary button, if cleared by the panel to select RESET, you can not answer.
How to use:
Start counting: counting terminal input contact signal, the counter starts counting.
Pause Count: Press count / Pause (PAUSE), suspended from counting; then click counts / Pause (PAUSE), resumes its count.
Panel clears: simply press the Delete key (RESET).
External clear: Clear terminal external contacts connected directly cleared.
Note:
1. the counter clear signal input signals and switch or circuit should be as close to the terminals of the counter, the signal lines as short as possible.
2. Avoid contact with others, such as: strong electrical wires or power wires, etc. with the tube or stranded traces to avoid unnecessary interference, if necessary,
use shielded cable, shield connected to the terminal + count on.
3. count signal and the clear signal input contact signal only, can not enter the other signals.
4. contact input should be reliable to avoid contact bounce caused by incorrect counting error is cleared.
5. When the LCD display fuzzy, replace the batteries with new ones. When a long time, remove the batteries to prevent battery leakage and damage deterioration counter,
remove the battery, and press the count / Pause (PAUSE), so that the screen display disappears, to close the counter inside the auxiliary battery.
Package:1 pcs digital counter + magnetic proximity switch + plastic round strong magnet + proximity switch mounting bracket in a package
eBay Cross Border Trade powered by ChannelEffect