Automatic tool changer electric spindle technical parameters
Spindle model: | RTM80-20-24Z/1.8 220V | Voltage: | 220V |
Maximum speed: | 24000rpm | Rated frequency: | 400Hz |
Electric current: | 5.4A | Motor level: | Level 2 |
Rated power: | 1.8KW (S1) | Peak power: | 2.1KW (S6) |
Rated torque: | 0.59Nm | Peak torque: | 0.84N |
Product overview
Automatic tool changer electric spindle parametric curve graph
Technical parameters:No. | project | Standard |
1 | Spindle blowing dust/seal gas pressure (MPa) | 0.2-0.25 |
2 | Spindle gas seal gas flow (L/min) | 65±10(When on Working) |
3 | Cooling water pressure (MPa) | ≥0.25 |
4 | Cooling water flow (L/min) | ≥2.5 |
5 | Cooling water temperature (degree) | 24-28 |
6 | Spindle static state pulse (µm) | ≤3 |
7 | Spindle vibration (mm/s) | ≤0.8 |
8 | Spindle diameter (mm) | Diameter 80 (0/-0.020) |
9 | Motor windings Pressure test (V/M) | 1000V/1 minute withstanding Voltage test |
10 | Tool Interface | ISO20 |
11 | Inverter Specifications | 2.2KW (220V) |
12 | Fitment | For castings, aluminum, glass, etc., and other processing |
4. Running-in program instructions
Only all monitoring issued no failures operational signals,at the same time,all safety devices have been installed and working properly,then allow start spindle.
Note: new or spindle which is not used for a long time must to be running slowly.First,start run spindle for half an hour as 25% of the maximum speed,then increase to 50% of the maximum speed,to run 15 minutes,finally, increase to maximum speed.It’s need to check the temperature of the spindle during the whole process, spindle will get hot, but not hot hand, if the spindle becomes hot, pls stop the operation and contact our customer service department.
5. Product backend interface instructions:
2.2KW ATC Spindle
1. Product overview
Spindle model | RTM80-20-24Z/2.2 220V | Voltage | 220V |
Maximum speed | 24000rpm | Rated frequency | 400Hz |
Electric current | 6.4A | Motor pole | 2 pole |
Rated power | 1.8KW (S1) | Peak power | 2.2KW (S6) |
Rated torque | 0.59Nm | Peak torque | 0.84Nm |
2. Drawing Size Description
Technical parameters | |
Spindle blowing dust/seal gas pressure (MPa) | 0.2-0.25 |
Spindle gas seal gas flow (L/min) | 65±10 (When on Working) |
Cooling water pressure (MPa) | >=0.25 |
Cooling water flow (L/min) | >=2.5 |
Cooling water temperature deg | 24-28 |
Spindle static state pulse (µm) | <=3 |
Spindle vibration (mm/s) | <=0.8 |
Spindle diameter (mm) | dia 80 (0/-0.02) |
Motor windings Pressure test (V/M) | 1000V/1 minute withstanding Voltage test |
Tool Interface | ISO20 |
Inverter Specifications | 2.2KW (220V) |
Fitment | For castings, aluminum, glass, etc., and other processing |
Spindle installation explanation
1) Circulating Cooling System Description
The system must ensure that the cooling water temperature of supply spindle is between 24-28deg. Usually setting the flow switch in return pipe of the cooling system,to ensure the supply of spindle cooling water. Cooling water requirements: we recommend using distilled water, while recommend Feinuokesi (Fenix) protective agent F1 (using the scale of 1: 200),coolant temperature is 26deg±2deg,inlet, outlet pipe temperature can’t exceed 5 deg.It is allowed As long as other monitoring can ensure fuller spindle cooling.
2) Air sealing control
In order to prevent water or impurities enters internal of the spindle,spindle will have gas sealing device,the gas seal machine must be started start with the machine at the same time. And the need to go through multi-stage filtration.
3) Compressed gas quality requirements
The quality requirement of gas which is used in gas seals:
Oil content:<0.01mg/m3
Solid particle:<5µ m
Pressure dew point: <7.5deg(0.7MPa)
4) Running-in program instructions
Only all monitoring issued no failures operational signals,at the same time,all safety devices have been installed and working properly,then allow start spindle.
Note: New or spindle which is not used for a long time must to be running slowly.First,start run spindle for half an hour as 25% of the maximum speed,then increase to 50% of the maximum speed,to run 15 minutes,finally, increase to maximum speed.It’s need to check the temperature of the spindle during the whole process, spindle will get hot, but not hot hand, if the spindle becomes hot, pls stop the operation and contact our customer service department.
Tech parameters:
1) Input Voltage: 220V(+/-15% )
2) Output Voltage: 220VAC
3) Input Frequency: 48-63 Hz
4) Output Frequency: 0-400 Hz
5) Input Phase: 1 phase
6) Output Phase: 3 phase
Product Feature:
1)PID control; advanced calculus PID closed-loop arithmetic, quick responding speed and high suitability;
2)Easy PLC function can realize 16 legs of speed and inverter control function;
3)RS485 communication port, adopting standard international MODBUS main circuit control;
4)With extremely strong anti-jamming capability
5)Low output ratting torque0.5HZ-150%, low speed running ability;
6)Carrier adjustable by 16KHZ, completely soundless working environment;
7)Broad voltage working area, normal running in 304V-456V;
8)Auto voltage regulation (AVR) technique, for ensuring the inverter load capability;
9)Various control technique by both synchronization and non-synchronization, dynamically realize fast starting without changing brakes;
10)With perfect errorprotection and short circuit starting protection capability;
R and T these 2 pins connect to single phase 220V AC power supply
Tech parameters:
1) Input Voltage: 220V
2) Output Voltage:0- 220V
3) Input Frequency: 50/60 Hz
4) Output Frequency: 0-1000 Hz
5) Input Phase: 1 phase or 3 phase (can connect to single phase 220-240V input)
6) Output Phase: 3 phase
Problem&Feedback
Please give us the opportunity to resolve any problem when you have, we concern your problem and we will try our best to resolve it.
We are a new member in ebay now, and need understand both of sides
Pls email us before you want to leave any negative feedback
Refund
When you have the parcel, and not satisfied the goods or it is other problem like as broken,pls tell us the detail reason and provide the photos
Any reason required for all refund. Item must be in it's original condition and no physical damage. Buyer responsible for all shipping cost
Contact us
Welcome worldwide customer inquire and questions, we will try to do our best to feedback customer’s email within 1-2 business days,if not pls check the mail box again
Customer’s satisfaction is very important to us.