Thinkcar Thinktool Pro as the 2024 most powerful Bi-Directional Scan Tool

✔ Thinkcar Thinktool Pro comes with 8 inch touch pad, Android 10 system, 6000mA/h battery for long time use, 2+32G memory storage for more vehicle software, more than 31+ reset functions free update for two years. 
No Language Barrier: English, France, Germany, Spanish, Italy, Portugal, Japan, Russia, Traditional Chinese supported.

✔ Thinktool Pro Scanner Tool Supports many popular OE-Level function: Auto-Auth for FCA SGW which makes pros works with Chrysler, Dodge, Jeep, Alfa Romeo and Fiat after 2017. Setting & Changeover (adblue reset, unlock the engine after a collision, cancel ABS driving test, and more) for Benz. Modification for BMW. ECU Coding, Customization, Personalization for worldwide vehicles, and keep growing.

✔ Register with Auto-Auth to enable Thinktool Pro tablet to communicate with the FCA SGW Authentication System and bypass the SGM, so as to perform diagnostics and bi-directionals without using a bypass cable. (but currently using this function needs to be paid, you can choose to use it o not.

✔ 2024 New Add Function For 2017 and later FCA Vehicles with Secure Gateway Module (SGW) Oil Reset, Elec. Throttle Adaption, IMMO Service, Injector Coding, Break-pad Reset, Steering Angle Reset, ABS Bleeding, AFS Reset, Battery Matching, A/T Learning, DPF Regeneration, EGR Adaption, TPMS Reset, Sunroof Initialization, Suspension Matching, Gear Learning, Airbag Reset, ODO Meter Reset, AdBlue Reset, A/F Reset, Coolant Bleeding, Language Change, NOx Sensor Reset, Seat Calibration, Stop/Start Reset, Transport Mode, Tyre Reset, Windows Calibration.

✔ Actuator Test: Injector Test, Turn Off ACC Lane Keeping Assist System (LKAS), Turn ON/OFF Front and Rear side ACM Solenoid, turning the fuel pump on and off, cycling the a/c, clutch on and off, Left clutch electromagnetic coil test, Acceleration Device Test, Oil Pressure Control Test, DYNAMIC camera aiming, Vehicle level position calibration, Brake Vacuum Pump, Inlet and Outlet Valve tests, Open Brakes tests, Wheel Speed Sensor Supply, PARKING BRAKE tests (Vary by car, Hundreds of functions, if not sure please check with us)

✔ Key Matching: Add, Delete, Rewrite smart keys, Replace smart key ECU, Replace KNOB IGNITION, Relearn key.

(Note: this Key matching function is NOT universally compatible, please check with us. Thinktool pro supports PIN-Code reading for most cars before 2008, for vehicles after 2008, you need to have PIN-Code to do Key matching)

✔ Component Matching: Compatible with for Volkswagen / for Skoda / for Seat / for BMW / for GM / for Ford / for Opel / for Mazda / for Fiat / for Honda / for Nissan / for Hyundai / for Kia / for Subaru etc.
✔ Online Coding: Compatible with for Volkswagen / for Audi / for Benz / for BMW / for Seat / for Porsche etc.
✔ Online Account Login Service: Compatible with for Volkswagen / for Audi / for Skoda / for Seat etc.
✔ Online Calibration: Compatible with for Volkswagen / for Audi / for Skoda / Seat etc.
✔ Online Parameterization: Compatible with for Volkswagen / for Audi / for Skoda / for Seat etc.
✔ Anti-theft IMMO Serivce: Compatible with for Volkswagen / for Audi / for Skoda / for Seat etc.
✔ Guided Functions: Compatible with for Volkswagen / for Audi / for Skoda / for Seat etc. Power Balance: Compatible with for Chrysler / for GM / for Ford etc.

THINKCAR THINKTool PRO supports Functions as the following :

 
1.THINKTOOL PRO support FULL SYSTEMS.
To diagnose car comprehensively, Thinkcar Thinktool Pro scanner can read DTCs and data streams, perform active test, Coding for ALL systems. For instance: Engines/Auto Transmission/Airbags/Immobilizer/Key Coding/ABS/Cruise Control/Instruments/ Self Leveling Suspension systems/Seats/Doors/Gateway/Steering Angle/Air Suspension/Body Systems/Electronic Power Steering & Motor Assisted/Power Steering/Tyre Pressure/Rain Sensors/4WD System/Stabilizer/Intelligent Parking Assist/Door Motors/Audio Systems/Air Conditioning/Tiptronic/Anti Theft/Soft Top/Headlamp Leveling/Central Locking/Automatic Clutch/ DPF Reset/Electric Windows/Plip coding/Heated Rear Window/Xenon Headlights/Wash Wipe/Fuel Burning Heater/Transfer Box/Seat Memory/Oil Life Service Reset/Sliding Doors/Electronic Throttle/Navigation System/Rollover Sensor/Cruise Control/ Multi Function Steering Wheel/Aux Heating/Electronic Parking Brake/Clutch Electronics, ....etc.

2.THINKTOOL Pro Support 28+ Kinds of Special Reset

1、Oil Reset
The lightening of the car maintenance light indicates that the vehicle needs maintenance.Reset the mileage or driving time to zero after the maintenance, so the maintenance light will go out and the system will start a new maintenance cycle.

2、Elec.Throttle Adaption
Elec. Throttle Adaption is to utilize the car decoder to initialize the throttle actuator so that the learning value of the ECU returns to the initial state.

3、Steering Angle Reset
To reset the steering angle, first find the relative zero point position for the car to drive in straight line.Taking this position as reference,the ECU can calculate the accurate angle for left and right steering.

4、Battery Matching
This function enables you to perform a resetting operation on the monitoring unit of vehicle battery, in which the original low battery fault information will be cleared and battery matching will be done.

5、ABS Bleeding
When the ABS contains air, the ABS bleeding function must be performed to bleed the brake system to restore ABS brake sensitivity.

6、Break-pad Reset
lf the brake pad wears the brake pad sense line, the brake pad sense line sends a signal sense line to the on-board computer to replace the brake pad.After replacing the brake pad, you must reset the brake pad.Otherwise, the car alarms.

7、DPF Regeneration
DPF regeneration is used to clear PM(Particulate Matter) from the DPF filter through continuous combustion oxidation mode (such as high temperature heating combustion, fuel additive or catalyst reduce PM ignition combustion) to stabilize the filter performance.

8、Gear Learning
After the engine ECu, crankshaft position sensor,or crankshaft flywheel is replaced, or the DTC 'gear not learned' is present, gear learning must be performed.

9、IMMO Service
To prevent the car being used by unauthorized keys, the anti-theft key matching function must be performed so that the immobilizer control system on the car identifies and authorizes remote control keys to normally use the car.

10、Injector Coding
Write injector actual code or rewrite code in the ECU to the injector code of the corresponding cylinder so as to more accurately control or correct cylinder injection quantity.

11、TPMS Reset
Note:Cooperate with wireless tire pressure diagnosis tool to realize TPMS activation, programming and learning functions

12、Suspension Matching
This function can adjust the height of the body. When replacing the body height sensor in the air sus pension system, or control module or when the vehicle level is incorrect, you need to perform thisfunction to adjust the body height sensor for level calibration.

13、AFS Reset
This feature is used to initialize the adaptive headlamp system.

14、A/T Learning
This function can complete the gearbox self-learning to improve gear shifting quality.

15、Sunroof Initialization
This function can set the sunroof lock off, closed when it rains,sliding /tilting sunroof memory function,temperature threshold outside the car etc.

16、EGR Adaption
This function is used to learn the EGR valve after it is cleaned or replaced.

17、ODO Reset
ODO reset is to copy, write, or rewrite the value of kilometers in the chip of odometer by using a car diagnostic computer and data cable, so that the odometer shows the actual

18、Airbag Reset
This function resets the airbag data to clear the airbag collision fault indicator.

19、Transport Mode
ln order to reduce power consumption, the following functions may be disabled, including limiting the vehicle speed, not waking up the door opening network, and disabling the remote control key, etc.At this time, the transport mode needs to be deactivated to restore the vehicle to normal.

20、A/F Reset
This function is applied to set or learn Air/Fuel ratio parameters.

21、Stop/Start Reset
This function is used to open or close the automatic start-stop function via setting the hidden function in ECU(provided that the vehicle has a hidden function and supported by hardware).

22、NOx Sensor Reset
NOx sensor is a sensor used to detect the content of nitrogen oxides (NOx) in engine exhaust. lf theNOx fault is re-initialized and the NOx catalytic converter is replaced, it is necessary to reset the catalytic converter learned value stored in the engine Ecu.

23、AdBlue Reset (Diesel Engine Exhaust Gas Filter)
After the diesel exhaust treatment fluid (car urea) is replaced or filled up, urea reset operation is required.

24、Seat Calibration
This function is applied to match the seats with memory function that are replaced and repaired.

25、Coolant Bleeding
Use this function to activate the electronic water pump before venting the cooling system.

26、Tyre Reset
This function is used to set the size parameters of the modified or replaced tire.

27、Windows Calibration
This feature is designed to perform door window matching to recover ECU initial memory, and recover the automatic ascending and descending function of power window.

28、Language Change
This function is used to change the system language of the vehicle central control panel.
.......

3..10000+ Vehicles Supported (Almost cars on the world)

Amarica car models:

For FORD,for LINCOIN,for GM,for BUICK,for CADILLAC,for CHEVROLET,for CHRYSLER,for DODGE,for JEEP,for HM

Europe car models：
For BENZ,for SMART,for SPRINTER,for BMW,for VW,for SKODA,for AUDI,for OPEL,for LAMBORGHINI,for PORSCHE,for MAYBACH,for EURO FORD,for LANDROVER,for DR,for BENTLEYRollsRoyce,for ROVER,for MINI,for VAUXHALL,for FERRARI,for FIAT,for Abarth,for LANCIA,for Alfa,for Romeo,for Maserati,for BUGATTI,for PEUGEOTCITROEN,for RENAULT,for SAAB,for VOLVO,for OPEL,for Dacia,for SEAT.

Malaysia car models:for PERODUA(PERODUA),for PROTON ;
IRAN car models:for IKCO,for MVM

Australian brand: for ford, forHolden 

India car models:for TATA,for MARUTI,for MAHINDRA 

Russia car models:For GAZ, for VAZ

Brazil car models： for FIAT,for GM

ASIAN CAR MODELS:
For SAMSUNG,for DAEWOO,for SSANYYONG,for HYUNDAI,for KIA,HONDA,for Acura,for TOYOTA,for SCION,for LEXUS,for MAZDA,for NISSAN,for Infiniti,for JPISUZU,for TLISUZU,for DAIHATSUSUZUKI,for MITSUBISHI,for SUBARU,for CHANGCHENG,for HUACHEN,for ZHONGXING,for JACTY,for QIRUI_TY,for ISUZU,for JINLONG,for CHANGAN,for LIUWEI_TY,for XINKAI,for JPISUZU,for ZHONGSHUN,for HAOQING,for HAFEI,for XIALI,for CHANGHE ZHONGTAI,for FLYER,for SSANGYONG,for JIAO,for WEILI,for LUXGEN.etc.

4.Graphical display

Combine: Displayed in graph merge status for data comparison.
Value: Displayed the parameters in values and shown in list format.
Customize: Customize the data stream option to be viewed. Tap the button, a pull-down list of the data stream items appears on the screen. Select the desired items (max12 items), and then screen will display the wave-forms corresponding to these items immediately. If you need to remove any items, just deselect them and delete.

5.THINKCAR THINKTool PRO supports Auto VIN read Function :

It can read VIN information automanually when you connect Car , fast get the inforamtion .

6.TPMS Function:

with wireless TPMS tool (optional), TPMS activation, coding and learning functions can be supported. 

(Need Extra ThinkTPMS G1 Tire Relearn Tool)

7.Matching:

such as throttle matching, anti-theft matching, steering angle matching and so on. When you replace parts or need data modification, ECU data should be used to match parts.

8.ECU CODING：

The Coding function is used to re-flash the vehicle control modules, it allows you to reprogram adaptive data for certain components after making repairs or replacements.

9.Actuation Test:

This function is used to test whether the execution components in the electronic control system can work.

10.Diagnostic Feedback

If you encounter an unresolved problem or diagnostic software bug during diagnosis, you can revert the most recent 20 test records to Thinkcar Team. When we receive your feedback, we will analyze and troubleshoot it in a timely manner, to improve the quality of our products and user experience.

11.Quick print diagnostic reports

Thermal printer, work with the main unit, also can work with module dock. Quick print diagnostic reports anytime and anywhere.

12.View History

Once a vehicle diagnosis is performed, thinktool pro will record the every detail of the diagnostic process. The History function provides quick access to the tested vehicles and users can resume from the last operation, without the necessity of starting from scratch.

13.Sypport REMOTE TECHNICAL SUPPORT
Sustainability tools for car repair shops 8 Modular expansion:

14.Support some optional modules: printer, work light, video-scope, battery tester, scope box, thermal image, module dock, wireless TPMS tool, HD Package(note: you can buy those models on ThinkStore）

15.Audi / VW firmware protection cancel features:

This feature helps mechanics replace car parts to carry out car modifications.

17.THINKCAR THINKTool PRO Supports Complete OBD2 functions:

1.Reading Codes: Show the detailed description of the Diagnostic Trouble Code (DTCs)
2.Erasing Codes & Reset: Turns off Check Engine Light (MIL), clears codes and resets monitors.
3.Data Stream: Reads and displays live ECU/PCM data stream, plotting functions graphically and stores freeze frame data.
4.I/M Readiness Status: Shows whether the various emissions-related systems on the vehicle are operating properly and are ready for inspection and maintenance testing.
5.Read Live Data Stream: Show the information of continuous data stream from a vehicle in live graphic (waveform) display.
6.View Freeze Frame Data: Check the certain vehicle conditions which are recorded by the on-board computer at the time the emission-related fault occurs.
7.O2 Sensor Test: Allows retrieval and viewing of O2 sensor monitor test results for the most recently performed tests from the vehicle’s on-board computer.
8.On-Board Monitor Test: Retrieves and displays test results for emission-related powertrain components and systems.
9.Read Vehicle Information: Display the information such as VIN (Vehicle Identification Number), CID (Calibration ID) and CVN (Calibration verification number), etc.
10.Component Test: Certain vehicle components can be actuated by commands sent from the scanner to test their operability.