IKEA Knäppa Digital Cardboard Camera Collector's Item VERY rare! new & sealed!

KNÄPPA
© Inter IKEA Systems B.V. 2012 AA-670669-2
Design and Quality
IKEA of Sweden
1 2
2s
3
PUTTING THE CAMERA TOGETHER
Please refer to the assembly instructions. The
2 AAA/LR03 batteries need to be inserted as
shown before assembling the camera.
TURNING THE CAMERA ON
Hold down the power/shutter button with your
finger for about 2 seconds. This is on the front
of the camera under the IKEA logo.
Check that the LED on the back of the camera
next to the viewfinder. A green light indicates
the camera is on.
TAKING A PICTURE
When the LED is green, click firmly the power/
shutter button, then LED starts to blink green.
The LED will blink green for about 8 seconds
while the picture data is being processed. The
camera will not take another picture while the
LED is blinking. Once the LED stops blinking it
is ready to take the next picture.
TURNING THE CAMERA OFF
Hold down the power/shutter button with your
finger for about 5 seconds until the green LED
goes out. The camera will also turn itself off
after about 60 seconds if it is not used.
CONNECTING YOUR CAMERA TO A
COMPUTER
Connect the camera to your a computer using
the built-in USB connector. The IKEA logo
should face up when plugging the camera into
a USB port. Once connected the camera will
appear:
- on a Mac desktop as a folder.
- as a new device in "My Computer" on a
Windows PC.
The camera does not need to be switched on
to transfer pictures.
DELETING PICTURES FROM THE CAMERA
If the LED on the camera flashes red, the
camera’s internal memory is full. Before you
can take more pictures, you need to make
room for new pictures by deleting older ones.
To delete pictures make sure the camera is
turned on. Then use a paperclip to press the
delete button on the front of the camera for
about 5 seconds. Note! This will delete all the
pictures on the camera. Please back-up all the
pictures on a computer before pressing the
delete button.
LOW BATTERY
The LED on the camera will shine red when
the camera’s battery power is low. You need to
replace the batteries as soon as you can.
BATTERY REPLACEMENT
Remove the plastic nuts and bolts at the top
of the camera, and place them in a safe place.
Remove the old batteries and then replace
making sure that the + and – symbols match
on the new batteries and circuit board. Then
reassemble.
TIPS
• Hold the camera still for about 3 seconds
before click the power/shutter button to
stabilize the sensor exposure time to the aim
in order to make sure your pictures are not
blurry.
• To help keep the camera steady, rest it on
something to help keep it stable.
• To improve picture quality avoid low light
levels.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/ TV technician for help.