BMW & New Mini Jacking Pad Tool Jack Pad Avoid Sill Damage.
Jacking Pad Adapter (SMALL TYPE).
This Jacking pad adapter is machined out of Tough Vulcanized Rubber (The same as Pucks or Car tyres ) it will protect your sill whilst jacking up your BMW/Mini. It is made of rubber in order to give you the strength to lift but also a small degree of flexibility.
This will help avoid any damage to the jacking area of your BMW and will slot into the jack pad allowing you to safely jack your car up.
It will work with the following models:
1 SERIES all models that use the plastic jacking points shown above.
2 SERIES all models that use the plastic jacking points shown above.
3 SERIES all models that use the plastic jacking points shown above.
4 SERIES all models that use the plastic jacking points shown above.
5 SERIES all models that use the plastic jacking points shown above.
6 SERIES all models that use the plastic jacking points shown above.
7 SERIES all models that use the plastic jacking points shown above.
X1 all models that use the plastic jacking points shown above.
X3 all models that use the plastic jacking points shown above
X4 all models that use the plastic jacking points shown above
X5 all models that use the plastic jacking points shown above
X6 all models that use the plastic jacking points shown above.
Z4 all models that use the plastic jacking points shown above.
Z8 all models that use the plastic jacking points shown above.
i8 (2014 - Present).
i3 (2013 - Present).
MINI R50, R52, R23, R55, R56, R57, R58, R59 & R60.
all models that use the plastic jacking points shown above .
THIS DATA IS CORRECT TO OUR KNOWLEDGE.
PLEASE INSPECT YOUR JACKING POINTS TO ENSURE COMPATIBILITY.
PLEASE ALSO CHECK YOUR CAR JACK FOR COMPATIBILITY AND YOU HAVE SUFFICIENT CLEARANCE.
This is a vital adapter for any BMW DIY, hobbyist or mechanic, it will help avoid any potential damage to the sills and as made of rubber so will not slip like steel on steel or plastic etc.
Dimensions:
Base - 60mm diameter.
Block - 28mm wide x 52mm long x 15mm high.
(all approx sizes +/- 1mm)
BE SAFE - SAFETY NOTE:
SO AS NOT TO CAUSE DAMAGE TO YOU JACKING POINTS. IT IS VERY IMPORTANT THAT THE LIFTING BLOCK ON THE LIFTING PAD IS A MINIMUM OF 14mm+ HIGH. GIVING YOU A SMALL CLEARANCE AROUND THE EDGE BEFORE LIFTING.
Note:
(i) Please check the size of your trolley jack head before buying.
(ii) The rubber raised section that fits into the BMW jacking pad should not be a tight fit in order to aid pad removal after jacking is complete.
(iii) The picture shows a Jacking Pad in the centre of a Trolley Jack. The bumpy section below the pad is part of the Trolley Jack NOT part of the Jacking Pad.ALL approx sizesClick LINK to view my full range of products.
FEEDBACK:
If you feel you are unable to give me 5 star positive feedback, please contact me and explain what you are unhappy with, I will try my best to resolve any problems you may have. Please don't judge me by things that are out of my control, like Royal Mail taking longer than expected, when my items are marked dispatched, that is when they are handed over to the post office. - Thank you...:-)
When jacking a car this should be done on solid level ground, the jack pad should be placed in the centre of the trolley jack head which must larger than the pad and jacked from and too a flat surface. Items purchased will comply with the Sale & Supply of Goods Act 1994 and be of “Satisfactory Quality” unless specified at the time of sale. Pads are manufactured and sold for DIY use only and not for Commercial use. Improper use could result in injury or damage. Note Rubber Jacking pads are classed as a consumable and will mark and wear over time and use. We take no liability for damage or injury caused whilst using this item any claims against us are limited to the cost of the item and consequential loss and labour claims are not accepted.. By accessing our website and/or placing an order, you agree to be bound by these terms & conditions. If Item is returned to us because item could not be delivered due to no one available to accept them then we will charge 20% of total to cover wasted postage cost. Title to the goods shall remain with us until paid in full with cleared funds. Please note our pads may still have the original puck logos from prior to us adding our UK Specific characteristics and specific technical expertise to the product Complies with ‘Made in Britain’ as defined in the Trade Descriptions Act 1968....
| For Customers that have already bought from us | |
|
| We strive to deliver 5 -star customer service. If you want to return the item for any reason (such like faulty/item does not match the description/order by mistake etc.). Or you didn’t receive the item. Please DO NOT select “return this item” or “I didn’t receive it” as it will lower our account rating. We are very grateful if you can select “contact seller” as the left picture show. After that it will come up several topic and please select " I have a question about using my item or I want to send the seller a message " as the below picture show. It is the fastest way to receive your message and we will resolve the problem as soon as possible.  |
