Bond It Super Mate Universal Siliconised Acrylic
Sealant Interior & Exterior
Description:
A high quality siliconised acrylic
sealant, suitable for use in a variety of interior and exterior applications.
Has
improved adhesion characteristics
when compared to conventional acrylic sealants. Provides a permanently
flexible long lasting seal which
adheres to virtually any materials. It also contains a powerful fungicide to
prevent
mould growth, and can be overpainted.
Conforms to EN15651‐1, F EXT‐INT.
Uses
For internal and external sealing
around timber and metal window
and door frames and internal sealing
around PVCu window and
door frames. Ideal for filling gaps
and cracks in general decorating
applications aswell as sealing cracks
and gaps in brickwork, stone,
plaster and concrete. Can also be
used as an adhesive for bonding
polystyrene coving and tiles and for
bonding cork tiles and wood
block flooring; and as a sealant for
PVCu profiles, cladding and
trims.
Preparation
All surfaces must be clean and free
from dust
and loose particles. Highly porous
substrates
such as new plaster should be primed
before
application with Bond It PVA BOND
diluted 1:4
with water. This product can be
applied to
slightly damp, but not wet surfaces.
Application
Apply using a standard sealant gun.
Cut the tip of the cartridge
taking care not to damage the thread.
Apply nozzle and cut cleanly
at an angle of 45° with an opening
slightly larger than the gap to
be sealed. Apply using a standard
sealant gun. Smooth down
within 20 minutes of application
using a wetted
spatula, piece of wood or Bond It
SEALANT
APPLICATOR TOOL. Care should be taken
at this
point not to saturate the surface as
this will
delay drying. Can be overpainted
after 1 hour
with waterbased paints (24-48hrs for
oil based paints).
Tools should be cleaned after use
using soapy water before
product cures.
Limitations
When using externally, in areas of
high humidity, protect from
water for a minimum of 12 hours. In
damp and cold conditions,
cure time will be significantly
extended. Not for use in conjunction
with bitumen or asphalt. Do not
attempt to abrade when cured.
Do not use around baths or shower
trays. We recommend use of
Bond It S3 SILICONE. Do not over
paint until a surface skin has
formed. Over painting is not
necessary. Note: this product is
flexible. Certain poor quality paints
(especially certain vinyl matts)
have very little movement in the dry
film. It is possible for the dry
paint film to crack if movement is
excessive. Should not be used in
conditions of continuous water
immersion, below ground level, in
areas of high abrasion (eg floor
joints). This product is not a
silicone sealant and is not suitable
for joints with very high
movement.
Container Size
EU3 plastic cartridge.
Colours
SUPER-MATE is available in white
only.
Shelf Life
Minimum 24 months from date of
manufacture when stored in
unopened tubes.
Storage Conditions
Store in cool, dry conditions at a
temperature between 5-25oC.
Protect from frost.
Disposal of Containers
Do not leave empty containers where
residue could be harmful to
children, animals or the environment.
Remove any containers to a
central disposal point in accordance
with local regulations.
Health & Safety
Please refer to separate material
safety data sheet for full
handling, use and storage
instructions. Keep out of reach of
children. It is the users
responsibility to determine suitability for
use. If in doubt contact our
Technical Department for advice.
Note: this information is for general
guidance only, since site conditions
and labour are beyond our control. It
is recommended that users make
their own tests to determine
suitability.
Value Base
All technical data stated in this
Data Sheet are based on laboratory tests. Actual measured
data may vary due to circumstances
beyond our control.
APPROVALS / STANDARDS
Certified to the harmonized European
standard EN15651-1 for façade applications internally
and externally in compliance with the
Construction Product Regulation.
Specification Summary
Density ca. 1.70 g/cm3
Solid Content ~85%
Shore A Hardness Approximately 22
Movement Capability Low to medium
(+/- 7.5%) EN15651-1
Chemical Resistance Dilute Acids -
Fair Dilute Alkaline – Fair
Aliphatic Hydrocarbons - Fair
Aromatic Hydrocarbons - Poor
Service Temperature -15 to +75°C
Ambient Air Temperature +5 to +30°C
Curing Time Full cure: 3 to 5 days,
dependent on thickness,
ambient temperature and humidity
Tack Free Time 15 to 60 mins,
dependent on thickness, ambient
temperature and humidity
Product Details:
Colour: White
Code: BDSMWH
Size: EU3
Barcode: 5056437400840
Package Content:
Bond It Super Mate Universal
Siliconised Acrylic Sealant Interior & Exterior