Product Description

AT10II 12 Channel Airplane Transmitter

*Frequently Asked Questions and User Manual's documents could be found on this page below.

*To works with Drone, you should replace the receiver to mini size R12DSM, R6DSM

*Note: Only binds to Radiolink's receiver: R12DS, R9DS, R12DSM, R6DS, R6DSM


About us:

Radiolink Electronic Co., Ltd. was established in 2003. We are specialized in researching, developing, and producing RC model radio transmitters, flight controllers, receivers, GPS, drones, airplane, and balance charger.

Our Values:

We have a professional R&D team, applied automatic production and testing instrument to provide high-quality, diversified, and competitive technological products to our customers, also including professional after-sales service.

AT10II Radio Key Features

for airplane, helicopter, FPV drone, Tamiya car and more

With DSSS&FHSS protocol, which makes AT10II with excellent anti-interference ability to all 12 channels, long range control up to 2.4 miles (4km). (Actual control distance depends on the flying environment)

  • 12 Channels & 15 Models Storage
  • Voltage Telemetry Built In (PRM-01)
  • Long Range Control Up to 2.4 Miles (4KM)
  • Dual/Triple Rate, EXP, EPA, Throttle Cut, Timer etc.
  • Wired/Wireless Training, RC Simulator/Crossfire Support
  • RSSI, Low Voltage, Fail Safe Alert Setting etc.
  • RC Models Selection (Glider, Helicopter, Quad, Airplane Car etc.)
  • Dual Sticker Adjustable (Left to Right Throttle and Self-back to Center)

AT10II Key Functions

Real-time Information Telemetry

AT10II works with PRM-03 module and flight controller APM or Pixhawk, Mini PIX, Turbo Pix can give you real-time important information on screen, like battery voltage, speed, altitude, RSSI, flight mode, yaw, roll, pitch and distance and more.

  • PRM-03 sold separately: B08QMW1KRY

Programmable Mix Control (8 Groups)

Easy to understand graph view, 5-12 channels can be programmed to any advanced setting. An Airbrake can be programmed by using pre-programmed mixes. Multi-servo elevator mixing for Flying Wings or V-Shaped tail models.

  • Refer to the online user manual for full details

Friendly Alarming

Low RSSI, low radio and receiver voltage alarm. with DD sounds and words remind on outdoor readable LCD. Screen background can be change to white for outdoor.

  • Factory default TX voltage alarm is 8.6v, please go to the PARAMETER-TX-ALARM to modify

Superb Ergonomically Designed

With 3 of VR switches, 3 of three-way position switches, 4 of two-way position switches, 1 of reset trainer switch. All 12 channels can be customized to any switch.

  • Transmitter size: 180x 95x 220mm (7.1” x 3.7” x 8.7”L*W*H) , weighs 0.95 kg (2.1 lb), can be easily to hold.

R12DS 12 Channels Receiver

Support PWM/SBUS signal output, 3-10V support.

  • Change Signal: press the Bind Button 2 times within 1 second.
  • To works with Drone, should replace the receiver to mini size R12DSM, R6DSM

Airplane Voltage Telemetry Module

Real-time telemetry airplane voltage monitor on AT10II's screen when paired with voltage telemetry module PRM-01. Model voltage alarming value can be customized.

  • Package included PRM-01

7dBi High Gain Antenna

With 7dBi high gain antenna, cuts down interference, that's ensure control range up to 4KM (2.4 Miles).

  • Lower signal noise with a channel Bandwidth of 5.0 MHz.
  • RF power output is over 100mW for a stable response.

Wired/Wireless Training Simulator Support

Support RC simulator wired/wireless training interface feature, AT10II compatible with the majority of aircraft simulator software like Realflight, PhoenixRC, FreeRider.

  • Note: Simulator an Crossfire module sold separately
  • wireless training cable: B089K4DJRG

Voltage Protection System

AT10II with reverse polarity protection circuit, do not worry about it damage even you insert wrong polarity. JST(2pin) connector is easily adapted for various battery layouts.

  • Battery box dimensions: 115(L)x32(W)x30.5(H)mm (4.5’’x1.25’’x1.2’’)
  • Batteries are not included

Support Update Firmware

AT10II radio is easily updated to latest firmware to get new features. Simply connect the transmitter to the PC with a USB cable for updating.

  • Not support update firmware with Mac computer

Works with Variety of Receivers

Only compatible with receiver from Radiolink, like R12DS, R9DS, R6DS, R12SM, R6DSM or TBS receiver when works with crossfire module.

  • Works with R12DS, R12DSM go to SYSTEM Menu, make sure CH-SELECT is 12CH
  • Works with R9DS, R6DS, R6DSM make sure CH-SELECT is 10CH

Adapts to Most of Types RC Models

Easy to understand user software makes quick work of changing aircraft types models: Fixed Wing, Airplane, Multirotor, Helicopter, Cars and Boats.

  • To works with FPV Drone, should replace the receiver to mini size R12DSM, R6DSM

Specifications:

Model Name AT10II
Spread Spectrum Mode DSSS&FHSS
Model Memories 15
Frequencies Band 2.4GHz ISM (2400MHz - 2483.5MHz)
Operating Current 105mA
Operating Voltage Range 7.4~15.0V (2S, 3S Lipos, 8*AA are acceptable)
Backlight LCD Screen 320×480 Pixel, 3.5 inch outdoor readable LCD
Compatible Receiver Radiolink R12DS, R9DS, R6DS, R12DSM, R6DSM
Channels 12 Channels 10/12 Channels 10/12 Channels 8 Channels 8 Channels 4 Channels
Voltage Telemetry Built-in Support Support Support Support
Control Range 2.4 Miles 2.4 Miles 2.4 Miles 1.2 Miles 1.2 Miles 1.2 Miles
Dimensions(L*W*H) 7.1*3.7*8.7 in 7.2*3.9*7.6 in 7.2*3.9*7.6 in 6.8*4*8.1 in 6.4*3.7*2.2 in 22*7 in
Weight 33.5 oz 31 oz 31 oz 16.6 oz 5.0 oz 7.3 oz
Package AT10II/R12DS/PRM-01 AT9S Pro/R9DS/Strap AT9S Pro/R9DS/Strap T8FB/R8EF T8S/R8EF A560 RTF Kit
Models Support Glider, Airplane, Multirotor, Helicopoter, Car, Boat, Robot etc Glider, Airplane, Multirotor, Helicopoter, Car, Boat, Robot etc Glider, Airplane, Multirotor, Helicopoter, Car, Boat, Robot etc Glider, Airplane, Multirotor, Car, Boat, Robot etc Glider, Airplane, Multirotor, Car, Boat, Robot etc Airplane