Maven MMA 3005-B Acrylic Black Color - Fast Set 3-6-Min MMA Adhesive-Thick/High Viscosity -1:1 ratio

maven MMA 3005-B Acrylic - Fast Set 3-6-Min MMA Adhesive-Thick/High Viscosity Black Color -1:1 ratio maven MMA3005-B is a two-part methacrylate adhesive suitable for structural bonding of various metals, plastics and composites. The product does not need surface preparation or a primer. This is a 1:1-part methacrylate adhesive with an open time of 3-6 minutes and handling strength can be achieved in less than 15 minutes. Give excellent bond strength on various substrates. Please Note: These cartridges are designed to work best with a 50ml or 400ml cartridge Dispenser, respectively. We advise you use a 50ml or 400ml Dispenser for all respective cartridges. If you do not have one, please check out our Dispensers, all are excellent products and have our 'it's good' seal of approval. If you prefer not to use a Dispenser, we have some 50ml kits that include hand tools or caulking dispenser adapters, as pictured, that you can use for fast small jobs. But the 400ml cartridges really need to use a 400ml Dispenser, they're just too big to effectively use without the dispenser. Key Features 3-6 Min Working Time Black Color Excellent General Purpose Fast-Set MMA for Craftsman and Industrial uses Bonds to wide variety of materials Electrically Insulating (does not conduct) Excellent resistance to water and solvents Cured Product Characteristics Color: BlackWork life (10 gm mass): 30-60 secondsHandling strength: 3-5 minutesFull cure: 1-2 hoursMixing Ratio: 1:1 Operating temp: -40F to 180F (-40C to 80C)Shore D Hardness: 80VOC Content: 0.1% Properties of uncured material (Resin)Specific Gravity: 0.99Viscosity@25°C, cP: 50,000 - 80,000Color Beige Properties of uncured material (Activator)Specific Gravity: 0.96Viscosity@25°C, cP: 50,000 - 80,000Color: Off-White to light Yellow Lap Shear: 2800-3800 psiTensile Strength: 3000-4000 psi Elongation (Failure strain): 6-18%Chemical resistance: Excellent resistant to hydrocarbons, acids and bases and susceptible to polar solvents. Directions of applicationsWipe off and decrease the surface to be bonded. Use the gloves to avoid skin contact. Dispense a desirable amount of adhesive using a dispensing dispenser. The nozzle sizes can be selected according to the desired bond thickness. Join the substrates with the specified work-life of this material and allow it to cure at room temperature. Do not disturb the parts during the curing process. Excess adhesive can be wiped off. (For optimum strengths, surface preparation for the metals like sandblast, etching will be needed). Safety and handlingWear safety glasses and gloves. Harmful if swallowed. Keep it away from heat, flames. Keep out of reach of children. Once used keep the containers closed. Storage and shelf lifeStore this product in a tightly closed container in a cool and well-ventilated area. Product should not be frozen. Keep it away from any source of heat. Store the material in between 51℉ to 75℉. Continuous exposure above 75℃ will reduce the shelf life.

Maven MMA 3005-B Acrylic Black Color - Fast Set 3-6-Min MMA Adhesive-Thick/High Viscosity -1:1 ratio

maven MMA 3005-B Acrylic - Fast Set 3-6-Min MMA Adhesive-Thick/High Viscosity Black Color -1:1 ratio

maven MMA3005-B is a two-part methacrylate adhesive suitable for structural bonding of various metals, plastics and composites. The product does not need surface preparation or a primer. This is a 1:1-part methacrylate adhesive with an open time of 3-6 minutes and handling strength can be achieved in less than 15 minutes. Give excellent bond strength on various substrates.

Please Note: These cartridges are designed to work best with a 50ml or 400ml cartridge Dispenser, respectively. We advise you use a 50ml or 400ml Dispenser for all respective cartridges. If you do not have one, please check out our Dispensers, all are excellent products and have our 'it's good' seal of approval.

If you prefer not to use a Dispenser, we have some 50ml kits that include hand tools or caulking dispenser adapters, as pictured, that you can use for fast small jobs. But the 400ml cartridges really need to use a 400ml Dispenser, they're just too big to effectively use without the dispenser.

Key Features

  • 3-6 Min Working Time
  • Black Color
  • Excellent General Purpose Fast-Set MMA for Craftsman and Industrial uses
  • Bonds to wide variety of materials
  • Electrically Insulating (does not conduct)
  • Excellent resistance to water and solvents

Cured Product Characteristics

Color: Black
Work life (10 gm mass): 30-60 seconds
Handling strength: 3-5 minutes
Full cure: 1-2 hours
Mixing Ratio: 1:1

Operating temp: -40F to 180F (-40C to 80C)
Shore D Hardness: 80
VOC Content: 0.1%


Properties of uncured material (Resin)
Specific Gravity: 0.99
Viscosity@25°C, cP: 50,000 - 80,000
Color Beige


Properties of uncured material (Activator)
Specific Gravity: 0.96
Viscosity@25°C, cP: 50,000 - 80,000
Color: Off-White to light Yellow

Lap Shear: 2800-3800 psi
Tensile Strength: 3000-4000 psi

Elongation (Failure strain): 6-18%
Chemical resistance: Excellent resistant to hydrocarbons, acids and bases and susceptible to polar solvents.


Directions of applications
Wipe off and decrease the surface to be bonded. Use the gloves to avoid skin contact. Dispense a desirable amount of adhesive using a dispensing dispenser. The nozzle sizes can be selected according to the desired bond thickness. Join the substrates with the specified work-life of this material and allow it to cure at room temperature. Do not disturb the parts during the curing process. Excess adhesive can be wiped off. (For optimum strengths, surface preparation for the metals like sandblast, etching will be needed).


Safety and handling
Wear safety glasses and gloves. Harmful if swallowed. Keep it away from heat, flames. Keep out of reach of children. Once uséd keep the containers closed.


Storage and shelf life
Store this product in a tightly closed container in a cool and well-ventilated area. Product should not be frozen. Keep it away from any source of heat. Store the material in between 51℉ to 75℉. Continuous exposure above 75℃ will reduce the shelf life.

×
×
×
×
×
×

Shipping info

Click the Shipping & Payments tab above the listing description for more info

Click the Shipping & Payments tab above the listing description for more info!

Additional delivery notes

PICK UP OPTION

Sorry, our items are NOT available for pick-up.

PAYMENT


Immediate payment is required upon selecting "Buy It Now" or upon checking out through the cart.

We accept payment via U.S. PayPal accounts and all Major Credit Cards, Debit Cards & Google Pay.

We are legally required to collect sales tax in those states and localities where we maintain a physical presence (nexus).

The applicable amount of sales tax charged to an order will be calculated based on the shipment destination's state and local sales tax laws.

Thank you for shopping with us on eBay!

Paying via Direct Deposit

Simply add the freight cost to the item cost and forward the total amount to the address to be provided following your purchase.

Additional Information

No additional information at this time

Ask seller a question

To contact our Customer Service Team, simply click the button here and our Customer Service team will be happy to assist.

Ask seller a question

© Perigee Direct

Click the Shipping & Payments tab above the listing description for more info

Accepted Payment Methods

Immediate payment is required upon selecting "Buy It Now" or upon checking out through the cart.

We accept payment via U.S. PayPal accounts and all Major Credit Cards, Debit Cards & Google Pay.

We are legally required to collect sales tax in those states and localities where we maintain a physical presence (nexus).

The applicable amount of sales tax charged to an order will be calculated based on the shipment destination's state and local sales tax laws.

Thank you for shopping with us on eBay!

Returns are accepted

Items must be returned within 30 days of the auction ending

Buyer will pay for return shipping.