Car Headlight Lens Scratches Yellowing Aging Blurring Cracking Restoration Kit Headlamp Refurbished Atomized Cup
Car Headlight Lens Scratches Blurring Cracking Restoration Kit Refurbished Cup
Repairing defects such as scratches, scratches, yellowing, aging, blurring, cracking, etc. on plastic headlights
Description of operation steps
(1) Grinding is done with sandpaper and water until the water is milky white. Then use sandpaper and water to polish until the surface is smooth and clean.
(2) Open the bottle, open the bottle cap, open the seal ring (must open the seal ring can be connected to the power supply, otherwise the heating of the coating solution in the tank will have the risk of ejection）
NOTE:Due to the liquid in the factory bottle, the customs can not pass, so the liquid is poured out before delivery, we do not charge the liquid, not the second use, 100% brand new.
(3) Connect the spray tube to connect household power supply(110V US Plug).
(4) After atomization coating is energized for 2 minutes, the spray port is 1 centimeters away from the lamp surface.
When operating, the brightness can be plated.
Do not coat the same place for a long time, so as not to affect the drying speed.
Attention OPERATION STEPS
1. It should be completely polished off the original coating on the lamp surface, not polished completely on the lamp surface can not be coated.
2. It is necessary to open the sealing ring of the tank to connect the power supply. Otherwise, the heated liquid will be heated.
3. When operating, the tank can not be tilted to more than 75 degrees. And prevent fog from dropping.
4. When the ambient temperature is below 20 ~C, heating the lamp to 50 ~C with a baking lamp or a hairdryer, or heating the lamp for 10 minutes before coating
5. When the coating solution is used up, please disconnect the power supply when the power indicator flashes.
6. Please wear protective glasses mask for good ventilation. If the film is splashed into the eyes, rinse immediately with plenty of water. If you accidentally inhaled steam, please move to the fresh air quickly and keep the airway open.
Capacity: 200ML
Rated voltage:110V
Package Include:
Atomization cup(Yellow or Red colors)
Set of sandpaper
Masking glue
Repairing defects such as scratches, scratches, yellowing, aging, blurring, cracking, etc. on plastic headlights
Description of operation steps
(1) Grinding is done with sandpaper and water until the water is milky white. Then use sandpaper and water to polish until the surface is smooth and clean.
(2) Open the bottle, open the bottle cap, open the seal ring (must open the seal ring can be connected to the power supply, otherwise the heating of the coating solution in the tank will have the risk of ejection）
NOTE:Due to the liquid in the factory bottle, the customs can not pass, so the liquid is poured out before delivery, we do not charge the liquid, not the second use, 100% brand new.
(3) Connect the spray tube to connect household power supply(110V US Plug).
(4) After atomization coating is energized for 2 minutes, the spray port is 1 centimeters away from the lamp surface.
When operating, the brightness can be plated.
Do not coat the same place for a long time, so as not to affect the drying speed.
Attention OPERATION STEPS
1. It should be completely polished off the original coating on the lamp surface, not polished completely on the lamp surface can not be coated.
2. It is necessary to open the sealing ring of the tank to connect the power supply. Otherwise, the heated liquid will be heated.
3. When operating, the tank can not be tilted to more than 75 degrees. And prevent fog from dropping.
4. When the ambient temperature is below 20 ~C, heating the lamp to 50 ~C with a baking lamp or a hairdryer, or heating the lamp for 10 minutes before coating
5. When the coating solution is used up, please disconnect the power supply when the power indicator flashes.
6. Please wear protective glasses mask for good ventilation. If the film is splashed into the eyes, rinse immediately with plenty of water. If you accidentally inhaled steam, please move to the fresh air quickly and keep the airway open.
Capacity: 200ML
Rated voltage:110V
Package Include:
Atomization cup(Yellow or Red colors)
Set of sandpaper
Masking glue
