X-Power Alpha Twin Exhaust 49cc Mini-Moto Dirt Bike - Rev and Go Automatic'
A great quality mini dirt bike; the latest X-Power Alpha Dirt Bike is a a perfect starter bike for both young and novice riders alike.
Built to a high specification for a mini-moto, the X-Power Alpha 2-stroke dirt bike uses high-performance parts as standard including over-sized 15mm carburettor, upgraded easy-start pull start, fast-action automatic clutch, key-operated ignition (with two keys!) and safety cable and clip.
Designed for the novice rider (minimum aged 6 onward in our experience and up to 65KG max weight), this mini dirt-bike is easy to start and has controllable power allowing riders to learn and understand the limits of the bike quickly without putting them selves in danger.
Being a rev and go' bike, the automatic clutch system takes the confusion of gears away from the rider allowing them to focus on the track ahead whilst alloy disk brakes provide reliable and instant stopping power.
For added safety the bike is fitted with a safety cable that clips to the rider which will cut-out the engine if the rider falls off the bike. The bike is chain-driven however the chain is fully enclosed for added protection.
The X-Power Alpha Bike includes the following features:
★ 49cc 2-Stroke Single Cylinder Air-Cooled engine
★ Unique twin exhaust design
★ Safety cut-off tether (bike will cut-out if rider falls)
★ Front and rear independently operated disk brakes
★ Chain driven drive system (chain fully enclosed for safety)
★ 1.35 litre fuel capacity
★ 20-22mph top speed
★ Two ignition keys
★ 15mm carb with overflow pipe for disposal of excess fuel
★ Fuel cut-off valve (to stop fuel leaking when not in use)
★ Suited for aged 6 onward (in our experience)
★ Maximum rider weight of 65kg (around 10 stone)
★ Comes with manual, 2-stroke mixing bottle and very basic tool kit
Size and Weight:
★ Length:125cm
★ Seat Height: 58cm
★ Handlebar Height: 80cm
★ Wheelbase: 85cm
★ Ground Clearance: 25cm
★ Weight: 25KG (without fuel)
Assembly Information - IMPORTANT
Please note, it is essential that you have mechanical knowledge to use this product. The bike is 90% assembled requiring a mechanically capable person to complete the assembly, properly check over all components of the bike and re-adjust parts where necessary.
You will also need to prepare the fuel mix, perform any troubleshooting needed and complete on-going maintenance to ensure the machine is kept in proper working order. Expect to get your hands dirty!
This bike will require around 45-60 minutes assembly in which you will need to complete the following:
1. Fit the front mudguard and number board
2. Fit the front wheel using the spacers and install the brake calliper.
3. Secure the handlebars and tighten the throttle/brake levers
4. Fit the bolt in the rear shock absorber and fit foot pegs.
5. Align and set the rear wheel to achieve the desired chain tension.
6. Apply the decals/sticker pack.
7. Check over all the nuts, bolts, fuel pipes etc to ensure nothing has come loose or moved during transit.
8. Check nothing is touching the engine that shouldn't be (i.e fuel lines etc).
9. Check fork alignment and adjust if necessary.
10. Check front and rear brakes are operating and adjust as required
11. Prepare the fuel mix (use a 25:1 to 32:1 mix only – i.e 15-20ml of oil per 500ml fuel)
12. Run-in the engine and make minor idle adjustments (if necessary)
It is critical to perform these tasks as it is your responsibility as the buyer to ensure the bike has been setup safe the rider to use. If in any doubt, contact us first!
It is recommended to follow our assembly steps mentioned above. The manufactures manual is quite basic so common sense and experience is required.
Please note, by purchasing this product you agree to have the mechanical ability to complete the assembly and maintenance as detailed above.
The package also comes with a 2-stroke mixing bottle and a (very) basic tool kit. We highly recommend using your own tools to assemble.
Return information
Returns are accepted within 30 days of delivery however the item must be un-used (not ridden) with no signs of wear. We cannot accept returns if the item has been used/ridden unless the product is deemed as faulty (note - not having the mechanical knowledge to assemble the item correctly is NOT a fault).