For Minolta SRT Super Pre-Cut Replacement Leather Seal 11 Colors
from Japan
 
Description

Hello. My name is Inaba.　I participate from Japan.
Thank you so much for watching this item page.
You can check the details of the commodity in the pictures. 

By all means, please look at the pictures.

Grade"total" :  New condition.  

     

 ※Caution※ Please confirm before applying.

      To replace the leather, you need to remove the self-timer.

       There is also a method without removing the self-timer, but this is not recommended as it may not stick well.

　　Tips for pasting (see bottom).

※Choice 1※ 

         There are 11 colors of seals. Please choose your favorite color.

         The camera shown in the color sample photo is different from For Minolta SRT Super.  It will be a color sample of leather. 

    Front 2 pieces + Rear 1 piece                                                                                                                     Please replace it at your own risk. Please be careful,You are responsible for any accidents caused by replacing the leather or light seal. Even if you make a mistake in the color or type, we cannot return, refund or exchange, so please check your model carefully. If the shape is different, please do not order.       


Includings

　      There is one set.

     The camera body and Lens is not included. Seal Only. Crab-eye wrench(Photo 3th), or pliers sharpened(Photo 4th) with a file or grinder, alcohol, and other tools required for exchange are not included.

 Important point

      Condition is a personal opinion.  

        Please check the photos carefully.

　    Please contact us if you have any questions.

　    Thank you for visiting.

About bundling

"Since I will shipping from two places, I cannot bundle shipping from different places."

         Title #number only and Title #G... cannot be bundled.

        Title #A... and Title #G... cannot be bundled.

        Title #W... and Title #G... cannot be bundled.

        Title #K... and Title #G... cannot be bundled.

        Title #number only, Title #A..., Title #K... and Title #W... can be bundled.

        Title #G... and Title #G... can be bundled.

Payment
Payment is due within 3 days of the auction end.
We will ship the item 5 business days after your payment clears.
Some countries have special delivery areas. In that case, We may ask for an additional shipping fee. 
Shipping
I send a product by Japan Post,UPS or FedEx.
You cannot choose a delivery company.
I attach the tracking number.
Please bid it without worrying.
Shipping is available from Monday to Friday.
Weekends and Japanese National Holiday are not available because post office is closed.
Returns
Unconditional Return Policy

Customer service and satisfaction are very important to us.
I have an unconditional return policy if notified within 30 days of the receipt of the item.

All returned items must be the original condition.
All return requests must be made within 30 days of the receipt of the item.

Please contact me first for return before you ship it back to me.
The postage of the returned goods is a buyer burden.
 

International Buyers
Please Note :
Import duties, taxes, and charges are not included in the item price or shipping cost. These charges are the buyer's responsibility. Please check with your country's customs office to determine what these additional costs will be prior to bidding or buying.
Re-paste method:
Please re-paste at your own risk. Leather cannot be returned, exchanged, or refunded due to the failure of leather replacement. Before starting work, please read the following text carefully and fully understand the work procedure before re-pasting.

Things to prepare：
  Crab-eye wrench(Photo 3th), or pliers sharpened(Photo 4th) with a file or grinder.
   A small amount of alcohol, benzene or nail polish remover.
   A cotton swab or paintbrush for applying alcohol, etc.

Procedure(The photo above is not SR-1)
   
 1.Before removing the original leather, remove the self-timer with Crab-eye wrench or  sharpened pliers(Photo 5th Upper left).You can remove it by turning it counterclockwise. There are 3 parts. Remember the state (order) in which the parts were attached when removing(Photo 5th Upper Right). Pry off the original leather from the edge using a small flathead screwdriver(Photo 5th Lower Left). Once the edge is peeled off, pull it off with your hand(Photo 5th Lower Right).

2.I'm going to peel off the original leather from the edge. If you drop alcohol on the adhesive surface or dip a paintbrush and cotton swab, in alcohol and apply it to the adhesive surface while peeling it off, it will come off easily(Photo 6th Upper Left).

Once the old leather has peeled off, clean the surface where the leather will be attached with alcohol or Sandpaper(very fine particles)(Photo 6th Lower Left).

Soak the adhesive side of the new leather with a little alcohol. Before the alcohol dries, you can reapply or make fine adjustments(Photo 7th Upper Left). I'm going to paste the new leather(Photo 7th Lower Left). Once pasted, put the self-timer back on. If the order of these parts is wrong, the self-timer cannot be assembled(Photo 7th Lower Right).

 3.The self-timer has been reset. Be careful not to overtighten the screw as it will break the screw(Photo 8th Upper Left). Open the back cover(Photo 8th Upper Right). I will paste this part(Photo 8th Lower Left). The corners of the edges are difficult to stick, so you may need to push them in with your fingernail or a sharp object(Photo 8th Lower Right).

 4.The back cover will be decided from the film sensitivity reminder part(Photo 9 Upper Left). Stick it along the edge(Photo 9 Upper Right). The corners of the edges are difficult to stick, so you may need to push them in with your fingernail or a sharp object(Photo 9th Lower Left).

 5. I don't think the other parts are difficult, so I won't explain them. "When the alcohol dries, it's complete".

Supplement: The ends of the camera are easy to peel off, so if you have glue such as G-17, G Clear, Cemedine Super X, Konishi Silex, etc., apply the glue to the red part in the above photo, let it dry, and then stick it on. It becomes very strong and you don't have to worry about it peeling off with normal use(Photo 10th).

If you don't have a crab eye wrench or sharp pliers:
Before starting work, read the following statements carefully and understand the work procedure before starting work.

1:Cut the part of the red line on the left of the photo 11th with scissors or a cutter.
2:Turn the leather over. Apply alcohol to the entire surface to be pasted.
　Insert the leather under the timer through the slit in the cut leather.
3:Paste the part below the timer (below the blue line).
4:Move the timer to below the blue line(green arrow).
5:Paste the top of the blue line.
6:End near the timer. After that, please paste according to the above method.