20W Magnetic QRP Antenna small loop antenna for high frequency transceiver ICOM-705 5-30mhz 76-108mhz 110-150mhz 400-450mhz
Description:
This is a portable small loop antenna. It is easy and quick to set up the antenna for your shortwave transceiver. Anti-interference, low standing wave, strong directivity, full frequency band. Thus, allowing you to enjoy multi-band reception and communication indoors, windows, balconies and outdoors.
Specifications:
Frequency Range:
144—148MHz
430-440MHz
7—30MHz
aeronautical band
FM radio also provides excellent reception
Tuning box:
Band selection switch, pull up 7MHz, pull down 14-30MHz
The upper knob is the frequency tuning knob, and the frequency tuning value does not change due to changes in the environment.
The lower knob is the impedance matching knob, and the impedance matching value will change due to changes in the environment.
Data transfer: 10W
SSB: 20W
installation method:
Use the right angle adapter and double male butt to connect the antenna to the m seat on the back of the radio and stand up or connect the ring body to the connector on both sides of the controller and tighten it, then mount the tripod to the mount on the back of the tuner , open the tripod, place the antenna body firmly on the tripod, and finally connect the feeder (the feeder is attached with a choke, and one end of the choke is close to the small loop antenna).
Now that the small loop antenna is connected to your station, you can now listen.
First, let's introduce the function of the tuner panel. The toggle switch on the left is the frequency band selection switch (upper: 7MHz, lower: 14-30MHz).
The main control knob, the upper knob is the frequency tuning knob, and the frequency tuning value will not change due to environmental changes; the lower knob is the impedance matching knob, and the impedance matching value will change due to environmental changes. (The adjustment range of the two knobs is 180 degrees, and the panel value is 0-12).
To start using the radio, select the desired frequency, then turn the band switch to the desired band position, then adjust the impedance matching value of the lower knob to 6, and then adjust the upper knob to tune. At this time, pay attention to the background noise of the radio. The more resonance there is, the greater the noise floor of the station. At this point, let the radio transmit (cw, fm, am modes are available), pay attention to the standing wave indication, and fine-tune the frequency tuning knob when transmitting. Since the knob of the portable version has no deceleration function, the fine-tuning method must be more delicate, and the smaller the rotation angle, the better.
At this time, it can be observed that the standing wave has obvious changes, but the minimum standing wave ratio is generally not lower than 1.5. At this time, the impedance matching knob needs to be adjusted. It is recommended to randomly adjust the positive and negative 5 scale values, and then repeat the steps of frequency tuning and observing the standing wave ratio. Due to the change of the matching value, there are two possibilities before the comparison, 1: the minimum value of the VSWR decreases; 2 the minimum value of the VSWR increases. If the minimum value of the standing wave ratio becomes lower, the impedance matching adjustment is close to the correct value, and further adjustment is possible. If the minimum value of the standing wave ratio becomes larger,
Repeat the above steps to adjust the VSWR of the antenna to 1.0.
For VHF and UHF bands, the upper knob is fixed to 12 to the end, and the lower knob can properly adjust the impedance resonance.
Note: It is best for outdoor use, indoor use of the antenna as close to the window as possible, in a fully enclosed environment with reinforced concrete, against a wall and other environments, the VSWR of some frequency bands is not ideal.
Advanced skills: When the signal is weak, the direction of the antenna can be rotated to improve the signal-to-noise ratio, which is beneficial to reception. The unique gain lobe of the loop antenna gives it horizontal gain directivity when upright. Using its characteristics, multiple signals in the horizontal direction can be selected in a targeted manner, and the co-channel interference in the horizontal direction can also be reduced. Of course, if the interfering signal is extremely strong, much larger than the useful signal that needs to be received, the weakening effect will not be too obvious, and it can still play a weakening role compared to the telescopic antenna.
The Scope of Use:
HF: 5~30MHz
Power: 20W
SWR: <1.2 (7MHz, 10MHz, 14MHz, 21MHz and 29MHz)
FM: 76~108MHz
VHF + Aviation Band: 110~150MHz
UHF: 400~450MHz
Package Included:
1X small loop antenna
1X2 meters transmitting antenna
1X5 meters 50 ohm coaxial cable
3X adapter
Deutsch
20 W magnetische QRP-Antenne kleine Schleifenantenne für Hochfrequenz-Transceiver ICOM-705 5-30 MHz 76-108 MHz 110-150 MHz 400-450 MHz
Beschreibung:
Dies ist eine tragbare kleine Rahmenantenne. Die Antenne für Ihren Kurzwellen-Transceiver lässt sich einfach und schnell aufbauen. Anti-Interferenz, niedrige Stehwelle, starke Richtwirkung, volles Frequenzband. So können Sie Multiband-Empfang und -Kommunikation in Innenräumen, Fenstern, Balkonen und im Freien genießen.
Spezifikationen:
Frequenzbereich:
144–148 MHz
430-440MHz
7—30MHz
Luftfahrtband
UKW-Radio bietet auch einen hervorragenden Empfang
Tuningbox:
Bandauswahlschalter, 7MHz hochziehen, 14-30MHz runterziehen
Der obere Knopf ist der Frequenzabstimmknopf, und der Frequenzabstimmwert ändert sich nicht aufgrund von Änderungen in der Umgebung.
Der untere Knopf ist der Impedanzanpassungsknopf, und der Impedanzanpassungswert ändert sich aufgrund von Änderungen in der Umgebung.
Datenübertragung: 10W
SSB: 20W
Installationsmethode:
Verwenden Sie den rechtwinkligen Adapter und den doppelten Stecker, um die Antenne mit dem m-Sitz auf der Rückseite des Radios zu verbinden und aufzustehen, oder verbinden Sie den Ringkörper mit dem Anschluss auf beiden Seiten des Controllers und ziehen Sie ihn fest, dann montieren Sie das Stativ am Montieren Sie auf der Rückseite des Tuners, öffnen Sie das Stativ, setzen Sie den Antennenkörper fest auf das Stativ und schließen Sie schließlich den Feeder an (der Feeder ist mit einer Drossel befestigt, und ein Ende der Drossel befindet sich in der Nähe der kleinen Rahmenantenne).
Jetzt, da die kleine Rahmenantenne mit Ihrer Station verbunden ist, können Sie jetzt hören.
Lassen Sie uns zunächst die Funktion des Tuner-Bedienfelds vorstellen. Der Kippschalter links ist der Frequenzband-Wahlschalter (oben: 7MHz, unten: 14-30MHz).
Der Hauptsteuerknopf, der obere Knopf ist der Frequenzabstimmknopf, und der Frequenzabstimmwert ändert sich nicht aufgrund von Umgebungsänderungen; Der untere Knopf ist der Impedanzanpassungsknopf, und der Impedanzanpassungswert ändert sich aufgrund von Umgebungsänderungen. (Der Einstellbereich der beiden Regler beträgt 180 Grad, und der Bedienfeldwert beträgt 0-12).
Um das Radio zu verwenden, wählen Sie die gewünschte Frequenz aus, drehen Sie dann den Bandschalter auf die gewünschte Bandposition, stellen Sie dann den Impedanzanpassungswert des unteren Knopfs auf 6 ein und stellen Sie dann den oberen Knopf auf Tuning ein. Achten Sie zu diesem Zeitpunkt auf die Hintergrundgeräusche des Radios. Je mehr Resonanz vorhanden ist, desto größer ist das Grundrauschen der Station. Lassen Sie an dieser Stelle das Funkgerät senden (CW-, FM-, AM-Modi sind verfügbar), achten Sie auf die Stehwellenanzeige und stellen Sie den Frequenzabstimmknopf beim Senden fein ein. Da der Knopf der tragbaren Version keine Verzögerungsfunktion hat, muss die Feinabstimmungsmethode feinfühliger sein, und je kleiner der Drehwinkel, desto besser.
Zu diesem Zeitpunkt kann beobachtet werden, dass die stehende Welle offensichtliche Änderungen aufweist, aber das minimale Stehwellenverhältnis ist im Allgemeinen nicht niedriger als 1,5. Zu diesem Zeitpunkt muss der Impedanzanpassungsknopf eingestellt werden. Es wird empfohlen, die positiven und negativen 5 Skalenwerte nach dem Zufallsprinzip anzupassen und dann die Schritte der Frequenzabstimmung zu wiederholen und das Stehwellenverhältnis zu beobachten. Durch die Änderung des Matching-Wertes gibt es vor dem Vergleich zwei Möglichkeiten, 1: der Minimalwert des VSWR sinkt; 2 erhöht sich der Minimalwert des VSWR. Wenn der Mindestwert des Stehwellenverhältnisses niedriger wird, liegt die Impedanzanpassungseinstellung nahe am korrekten Wert, und eine weitere Einstellung ist möglich. Wenn der Mindestwert des Stehwellenverhältnisses größer wird,
Wiederholen Sie die obigen Schritte, um das VSWR der Antenne auf 1,0 einzustellen.
Für VHF- und UHF-Bänder ist der obere Knopf auf 12 bis zum Ende fixiert, und der untere Knopf kann die Impedanzresonanz richtig einstellen.
Hinweis: Es ist am besten für den Außeneinsatz, den Inneneinsatz der Antenne so nah wie möglich am Fenster, in einer vollständig geschlossenen Umgebung mit Stahlbeton, an einer Wand und anderen Umgebungen, das VSWR einiger Frequenzbänder ist nicht ideal.
Fortgeschrittene Fähigkeiten: Wenn das Signal schwach ist, kann die Ausrichtung der Antenne gedreht werden, um das Signal-Rausch-Verhältnis zu verbessern, was für den Empfang von Vorteil ist. Die einzigartige Verstärkungskeule der Rahmenantenne verleiht ihr eine horizontale Verstärkungsrichtwirkung, wenn sie aufrecht steht. Durch seine Eigenschaften können gezielt mehrere Signale in horizontaler Richtung selektiert und auch die Gleichkanalstörungen in horizontaler Richtung reduziert werden. Wenn das Störsignal extrem stark ist, viel größer als das zu empfangende Nutzsignal, ist der Schwächungseffekt natürlich nicht zu offensichtlich und kann im Vergleich zur Teleskopantenne immer noch eine schwächende Rolle spielen.
Der Anwendungsbereich:
KW: 5~30 MHz
Leistung: 20W
SWR: <1,2 (7MHz, 10MHz, 14MHz, 21MHz und 29MHz)
UKW: 76~108 MHz
VHF + Luftfahrtband: 110~150MHz
UHF: 400~450 MHz
Lieferinhalt:
1X kleine Schleifenantenne
1X2 Meter Sendeantenne
1X5 Meter 50 Ohm Koaxialkabel
3X-Adapter