ON BACK ORDER UNTIL 9/16/22  PLEASE WAIT UNTIL THEN TO ORDER.  THANK YOU


These Come with a THREE YEAR Factory ONLY Warranty  if you receive a defective Gecko Drive (which is VERY rare)  You need to log onto Geckodrive.com and fill out their RMA form, then send the drive to them for replacement or repair allow a few days, after they have checked the Driver, for return of repaired or replaced product.  By Purchasing these Drivers you agree to the above

The Picture only shows 4  BUT you will receive FIVE.

You are buying FIVE BRAND NEW fresh from the factory and newly released GECKODRIVE G-203V single axis stepper motor driver The NEW BULLET PROOF Driver from Geckodrive. This listing purchase includes extras that you do not get from the factory read on. I recently decided to become a Gecko distributor, and decided to offer EXTRAS with your purchase from me that you do not get from the factory.  With this purchase you will receive a FREE complete set (sells $7.99 in my store) of the needed 1/4 watt amp control resistors, to set the amp output of the driver to match your motor's needs.  The Twelve pack resistor set includes the resistors that will allow you to set the G-203V to any of the following Amp outputs for your motor.  1.0 amps, 1.5 amps, 2.0 amps, 2.5 amps, 3.0 amps, 3.5 amps, 4.0 amps, 4.5 amps, 5.0 amps, 5.5 amps, 6.0 amps, 6.5 amps and 7.0 amps per phase.  I also offer a very low comparative shipping and handling price of $9.99 USA.  This item comes with One Year factory warrantee. All returns must go to Geckodrive accompanied by their return data sheet.   Add it up, and it makes sense to buy this from me. Save on a lot of two, or 3 lot or 4 lot in other listings in my store.  thanks Brent

You also receive a manual on CD

Drive Specks:

  • 7A 80 VDC maximum power ratings
  • 10 microstep fixed resolution
  • Mid-band resonance damping
  • short-circuit protection
  • Reversed-polarity protection
  • Over-temperature protection
  • Over-voltage protection
  • Optoisolated STEP, DIRECTION and DISABLE inputs
  • Optoisolator COMMON is ground
  • 2.5V, 3.3V and 5V logic compatible inputs
  • Recirculate mode while motor is stopped
  • 305 kHz maximum Step puls frequency
  • Tot Settable adjust trimpot
  • Power and error LED indicators
  • No user settable jumpers inside
  • Morphs to full step at higher speeds to maximize motor torque
  • internal socketted fuse
  • Power-on reset
  • 20 kHz switching frequency
  • Same size and terminal pin-out as the G201

  •  

    • Important note about SHIPPING:

     

    ·    ON Multiple item orders only, NOT on single item orders,  SHIPPING COST totals can become UNREASONABLY HIGH due to the necessity for Ebay to add up all of the individual shipping costs for an estimated “not to exceed” total ship cost.  A high ship cost total on your order will be corrected by us, but only if you place your multiple order and WAIT to PAY,  UNTIL after we send you an invoice with COMBINED shipping. Don’t use a cart to order your multiples because it forces you to pay immediately on checkout, and, we can’t then invoice you for combined shipping on your order once you have paid.

     

    Thanks for reading and be sure to Google Hubbard CNC to see our glowing reviews and other spectacular deals we have online!

     

     THE MESSAGE ABOVE ONLY APPLIES TO PEOPLE ORDERING MORE THAN ONE TYPE OF ITEM FROM OUR STORE!

     

    ALSO:

     

    ·         PROBLEMS with the Shipment -- Communicate with us ONLY BY EBAY MESSAGE. DO NOT communicate with the paypal email beginning alice.hubbard, this is an order Depository email only, we do not monitor it.