You are buying one new
Wind turbine with charge controller kit
Missouri Freedom 1600 watts max
5 Blade wind turbine 12 volt and
440 amp 10,000 watt Digital charge controller
It has a 14 magnet rotor inside and our skewed stator core for easy turning and
comes with 1 rectifier, includes one locking collar and one nylon washer
Stainless steel keyed shaft and No Cogging!
RAPTOR GENERATION 4 BLADES ™
Up to 1600 watts max output.
Starts up in just 3 to 4 mph winds
Cut in at 6 mph
Powder coated for a 50 year finish
no painting required
Wind turbines for the beginner How to part one by Missouri Wind and Solar - YouTube
Video will open in a new window
Here's what you get in the package
Freedom 5 blade wind turbine
- Freedom PMG (PERMANENT MAGNET GENERATOR) WITH 14 MAGNET ROTOR.
- 125,000 hours + of rated bearing life.
- Freedom PMG has no brushes, Stainless steel rotor shaft, very dependable!
- Heavy duty hub spacer/stabilizer with slot to fit keyway
- Mounting Bracket and Heavy Duty 2 arms tail assembly.
- Powder coated!
- Tail fin measures 29" tall for maximum tracking.
- Mounting Bracket Fits on 1.5" schedule #40 or #80 pipe.
- Comes with 5 gray nylon carbon fiber composite blades.
- Aerodynamically tapered Genuine RAPTOR GENERATION 4 Blades™ for maximum output.
- Steel blade hub is 3/16'' thick Zinc Plated
- Blades Make 61" dia.
- 5 blade Turbine weighs 49 lbs.
- Limited Warranty (click here for details)
The charge controller
12 VOLT 440 AMP 10,000 WATT DIVERSION / DISCONNECT CHARGE CONTROLLER
WITH BUILT IN DIGITAL DISPLAY AND INTELLIGENT DUAL PROCESSOR CONTROLLER
Does wind turbine and solar panels at the same time
THE MISSOURI WIND MW440DIG CHARGE CONTROLLER
Dual (2) Microprocessor controlled -- Very stable and very accurate
- Multiple user changeable settings, and trip points for many various system requirements and applications-
- You can change the dump point voltage level, end of dump voltage level, length of time in divert mode when end dump point voltage is reached (between 0 to 999 seconds, or 0 to 999 minutes)
- Isolated Electronics Protection - Almost impossible to accidentally connect wind or solar directly to the circuit board.
- High amp rating - Can be operated at 100% duty cycle conducting surge loads up to 440 amps or 10,000 watts. Please note that the normally closed contacts can handle 100 amps continuous duty.
- Battery Status LED - Lets you know your battery's actual voltage!
- Green LED on board lets you know it's in dump mode
- Plug & Play - Long leads for easy termination to your 12 volt battery or battery bank.
- Can divert the charging source from the batteries to the load, or dump both the batteries along with the charging source.
- You can connect both wind and solar at the same time
- Reverse polarity protection
- Ultra low power consumption even with the volt meter on (almost negligible). You can even set the volt meter to turn off after in-activity.
- On board relay- Isolates electronics from back voltage spikes from large 440 amp relay. This is important to get the longest life out of the electronics. No one else has this!
Our Freedom PMG™ permanent magnet generator is specifically designed for wind turbine use and can even be used with vertical axis wind turbines (VAWT).
Why buy a Freedom PMG™ over a Delco car alternator PMA?
The answer is simply the Freedom PMG was designed for wind turbine use and more copper!
More copper in the stator core equals more power.Each Freedom PMG™ rotor contains twice as much copper than any Delco style PMA.
Freedom PMG Specifications:
- 17 mm stainless steel shaft compatible with all Missouri Wind and Solar hubs and blade sets
- Custom hub spacer/stabilizer with keyway and bolts for attaching to Missouri Wind and Solar blade hubs
- Zinc plated 14 rare earth neodymium magnet rotor
- No brushes to fail or replace
- Large, heavy duty bearings in front and back
- Fits delco bolt patterns and mounts up to our standard mounting bracket
- 3/8" Diameter bolt holes
- 1 15/16" on center between mounting holes
- 5 7/8" OD Width
- 6 5/16" Tall
- 10 pounds
