This is a pair of HID Hi/Lo H4-3 globes. 2 x Globes and they are brand new, here in Melbourne ready to post
These are JTX Premium Alloy globes.
Ideally we have listed these so people can buy a spare globe or pick up a replacement for a kit that is out of warranty or maybe try some new colours. Typically this "Premium" globe will work on just about every single H4 Hi/Lo HID kit out there on the market. We sell to a lot of people who have had trouble with cheap kits.
This globe is exclusive to us - we identified where the normal H4 HID globes were failing and addressed these with the factory. The following improvements were made ...
The specs are as follows ..
Here is what makes up the globe. Although it should never be required you can in fact take it apart to service it and we could replace a component years down the track if needed. Now I promise you cant get that from a Chinese supplier or his plastic globe...
In the HID world this globe is referred to as H4-3 shifting. The globe part comes on and stays on no matter which beam. In low beam the bottom half of the light's reflector is shaded so as not to cast light upwards. When you flick to hi beam the globe stalk shifts by use of a solenoid powered by 2 thin wires in the wiring harness. Not only does the bright spot of the globe shift into the focal point of the reflector but light is no longer shaded and all of the light's reflector casts light . It's common knowledge that HID globes take a few seconds to reach full brightness - by not turning on or off between hi and low there is no dark time or warm up periods.
The process of fitting these to lights is as follows. (Be careful not to touch the glass with your fingers)
Step 1. Twist the globe apart at the green seal. It is a 1/4 turn anti-clockwise with your right hand and then pull apart.
Step 2. Boot easily slips onto globe. Slide the boot as far back as it will go as this makes room for connections later.
Step 3. Fit the globe base to the light and lock it into place.
Step 4. Fit globe back to base in the light - remember a 1/4 turn this time clockwise to lock it in. It will only click together easily one way but if you are unsure of which way up the globe clicks in it will sit so the shield is sitting like a cup as if it could hold water. The shield has to shade the bottom half of the light.
Then push the rubber boot back along the globe towards the light as far as you can get it so the boot has a good tight fit against the light. That will ensure dust and water stays out.
You cant just plug this into a light and expect it to work. Being HID it needs a ballast and a wiring harness which are all in my complete kit which I also sell. I also sell these parts separately. If you are new to HID and want a full kit then here is the link to my very popular and most reliable and waterproof kit ..
This globe would suit every H4 HID kit I have ever sold. The Ballast plugs are universal with all HID kits so even if you have someone else's kit this would suit as a spare or replacements. Here's a note - the bigger wires that run from ballast to globe carry 23,000Volts and so dont go cutting them as they will never work properly again if re-joined. The thin solenoid wires can be cut and soldered in the event you have an different hi/lo plug . These plugs can vary but these wires can be cut.
I stock these globes and they are ready to send to you.
We have sold thousands of these and so through the test of time we can confidently warranty these for 1 year knowing they are excellent quality. We can see from your feedback we automatically leave you when you pay that you are covered and so no need to even come up with proof of purchase. Being based here in Melbourne it's a fast easy process.
Here's an explanation for each... Halogen is incandescent meaning power runs through a very fine wire which glows hot. It is surrounded by Halogen gas which not only contains no oxygen so there can be no rusting but Halogen shines brightly when heated. LED (Light Emitting Diode) has come ahead in leaps and bounds and offers very bright light especially up close to the vehicle. The light source is over a larger area and so it spreads wide to the delight of most drivers but much of it is not in the focal point of the light and so doesn't travel great distance. HID (High Intensity Discharge) trumps everything with exceptional brightness and very long range. The light output of HID is amazing. HID works by passing a constant spark or arc of electricity across a field of Xenon gas. To achieve such an arc the volts are increased by ballasts which transform 12v or 24v to 23,000 volts. By it's very nature power at those volts wants to short out and so it is imporatnt to stick with quality brands such as JTX when using HID to maintain reliability.
Just click on the one you want to be linked to .....
About Us - JTX Lighting is an Australian family owned business and have been long time specialists in lighting products for cars, trucks, 4WD's, bikes and boats. Whether you need to just replace a blown globe, want brighter lights, upgrading spotties or out to enhance the look of your ride JTX Lighting can rescue the night.
We are on the web and facebook as well as here on eBay.
We make some of our items right here in Melbourne and we are proud to say we are the only automotive lighting company registered and approved by the Australian Made organistion.
Payment
Shipping
We accept PayPal. It's automatic when you buy and almost everyone has a Pay Pal account nowadays.
If you don't have a Pay Pal account that's still OK, Ebay can take your card details when you buy and they use Pay Pal as their way of doing that. Your card details remain safe. Only Pay Pal see your details.
We do FREE shipping on all orders!
Your order will be dispatched on the same or next working day of your purchase.
We use regular Aus Post or a courier service and we dont charge you for that.
EXPRESS - When you check out you may upgrade to Aus Post Express (Yellow Bag) which costs just a bit more.
All of our stock is here in Australia and ready to send to you straight away.
In the very unlikely event that your item is lost or damaged during post, then WE are responsible and will make sure a replacement is sent.
Buy with confidence from JTX Lighting knowing your goods will be in your hands within a matter of days.
Returns
If you ordered the wrong size or type then we will swap it over - it's not a problem.
If you are not 100% satisfied with your purchase then just send it back for a refund or replacement - it's not a problem.
You have 30 days from purchase for a change of mind return or exchange request.
All of our items have a 12 month Warranty which covers replacement parts. Send the old part back to us for testing and we repair or replace it. We can make sure you send the right part back by asking you to do a few simple tests. Contact us by ebay message or call us on 0416611774 to make such arrangements.
For a lot of our products we actually make or assemble them right here in our Melbourne facility so we would have the parts and technical skill to make sure you are totally looked after.
The JTX Lighting Guarantee
We are based in Melbourne and all of our stock is here in Melbourne. You are not waiting for postage from China with a company pretending to be in Australia. So you will get your goods within a matter of days.
We can handle all your after sales support needs, guarantee the parts fit and will fix or replace them under warranty, all from Melbourne and again within days.
This is a pair of HID Hi/Lo H4-3 globes. 2 x Globes and they are brand new, here in Melbourne ready to post
These are JTX Premium Alloy globes.
Ideally we have listed these so people can buy a spare globe or pick up a replacement for a kit that is out of warranty or maybe try some new colours. Typically this "Premium" globe will work on just about every single H4 Hi/Lo HID kit out there on the market. We sell to a lot of people who have had trouble with cheap kits.
This globe is exclusive to us - we identified where the normal H4 HID globes were failing and addressed these with the factory. The following improvements were made ...
The specs are as follows ..
Here is what makes up the globe. Although it should never be required you can in fact take it apart to service it and we could replace a component years down the track if needed. Now I promise you cant get that from a Chinese supplier or his plastic globe...
In the HID world this globe is referred to as H4-3 shifting. The globe part comes on and stays on no matter which beam. In low beam the bottom half of the light's reflector is shaded so as not to cast light upwards. When you flick to hi beam the globe stalk shifts by use of a solenoid powered by 2 thin wires in the wiring harness. Not only does the bright spot of the globe shift into the focal point of the reflector but light is no longer shaded and all of the light's reflector casts light . It's common knowledge that HID globes take a few seconds to reach full brightness - by not turning on or off between hi and low there is no dark time or warm up periods.
The process of fitting these to lights is as follows. (Be careful not to touch the glass with your fingers)
Step 1. Twist the globe apart at the green seal. It is a 1/4 turn anti-clockwise with your right hand and then pull apart.
Step 2. Boot easily slips onto globe. Slide the boot as far back as it will go as this makes room for connections later.
Step 3. Fit the globe base to the light and lock it into place.
Step 4. Fit globe back to base in the light - remember a 1/4 turn this time clockwise to lock it in. It will only click together easily one way but if you are unsure of which way up the globe clicks in it will sit so the shield is sitting like a cup as if it could hold water. The shield has to shade the bottom half of the light.
Then push the rubber boot back along the globe towards the light as far as you can get it so the boot has a good tight fit against the light. That will ensure dust and water stays out.
You cant just plug this into a light and expect it to work. Being HID it needs a ballast and a wiring harness which are all in my complete kit which I also sell. I also sell these parts separately. If you are new to HID and want a full kit then here is the link to my very popular and most reliable and waterproof kit ..
This globe would suit every H4 HID kit I have ever sold. The Ballast plugs are universal with all HID kits so even if you have someone else's kit this would suit as a spare or replacements. Here's a note - the bigger wires that run from ballast to globe carry 23,000Volts and so dont go cutting them as they will never work properly again if re-joined. The thin solenoid wires can be cut and soldered in the event you have an different hi/lo plug . These plugs can vary but these wires can be cut.
I stock these globes and they are ready to send to you.
We have sold thousands of these and so through the test of time we can confidently warranty these for 1 year knowing they are excellent quality. We can see from your feedback we automatically leave you when you pay that you are covered and so no need to even come up with proof of purchase. Being based here in Melbourne it's a fast easy process.
Here's an explanation for each... Halogen is incandescent meaning power runs through a very fine wire which glows hot. It is surrounded by Halogen gas which not only contains no oxygen so there can be no rusting but Halogen shines brightly when heated. LED (Light Emitting Diode) has come ahead in leaps and bounds and offers very bright light especially up close to the vehicle. The light source is over a larger area and so it spreads wide to the delight of most drivers but much of it is not in the focal point of the light and so doesn't travel great distance. HID (High Intensity Discharge) trumps everything with exceptional brightness and very long range. The light output of HID is amazing. HID works by passing a constant spark or arc of electricity across a field of Xenon gas. To achieve such an arc the volts are increased by ballasts which transform 12v or 24v to 23,000 volts. By it's very nature power at those volts wants to short out and so it is imporatnt to stick with quality brands such as JTX when using HID to maintain reliability.
Just click on the one you want to be linked to .....
About Us - JTX Lighting is an Australian family owned business and have been long time specialists in lighting products for cars, trucks, 4WD's, bikes and boats. Whether you need to just replace a blown globe, want brighter lights, upgrading spotties or out to enhance the look of your ride JTX Lighting can rescue the night.
We are on the web and facebook as well as here on eBay.
We make some of our items right here in Melbourne and we are proud to say we are the only automotive lighting company registered and approved by the Australian Made organistion.
Payment
We accept PayPal. It's automatic when you buy and almost everyone has a Pay Pal account nowadays.
If you don't have a Pay Pal account that's still OK, Ebay can take your card details when you buy and they use Pay Pal as their way of doing that. Your card details remain safe. Only Pay Pal see your details.
Shipping
We do FREE shipping on all orders!
Your order will be dispatched on the same or next working day of your purchase.
We use regular Aus Post or a courier service and we dont charge you for that.
EXPRESS - When you check out you may upgrade to Aus Post Express (Yellow Bag) which costs just a bit more.
All of our stock is here in Australia and ready to send to you straight away.
In the very unlikely event that your item is lost or damaged during post, then WE are responsible and will make sure a replacement is sent.
Buy with confidence from JTX Lighting knowing your goods will be in your hands within a matter of days.
Returns
If you ordered the wrong size or type then we will swap it over - it's not a problem.
If you are not 100% satisfied with your purchase then just send it back for a refund or replacement - it's not a problem.
You have 30 days from purchase for a change of mind return or exchange request.
All of our items have a 12 month Warranty which covers replacement parts. Send the old part back to us for testing and we repair or replace it. We can make sure you send the right part back by asking you to do a few simple tests. Contact us by ebay message or call us on 0416611774 to make such arrangements.
For a lot of our products we actually make or assemble them right here in our Melbourne facility so we would have the parts and technical skill to make sure you are totally looked after.
The JTX Lighting Guarantee
We are based in Melbourne and all of our stock is here in Melbourne. You are not waiting for postage from China with a company pretending to be in Australia. So you will get your goods within a matter of days.
We can handle all your after sales support needs, guarantee the parts fit and will fix or replace them under warranty, all from Melbourne and again within days.