1. Be sure to disable/uninstall anti-virus software
Please note,anti-virus software can flag up this item software as having a virus. This is a false positive and is due to the software containing the application file. So Before setup the device software, please disable/uninstall anti-virus software or install a more reliable free virus scanner! Our this item software is completely safe and virus free and all other virus scanners confirm this.
If the software data is destroyed or lost because you forget to disable/uninstall anti-virus software, please contact our customer service, we can send you the software via internet.
2. Required windows operation system is windows XP
Be sure to setup and run the device software under windows XP. Otherwise the device software and program can be broken or it will fail to work.
Lastest
version 5.0, support VDO with 24C32 or 24C64,our vagtacho usb version
5.0 includes the functions of vagtacho usb 4.52 , vagtacho usb 4.0,
and vagtacho usb 3.5
VAG Kombiinstrument / Immo box eeprom programmer!
Support
for some VDO dashes for VW from year 2009-2011 with NEC mcu and 24C32
or 24C64 eeprom memory. Important: These dashes requires ignition to be
switched on with valid key of the car! Software version 5.0 works ONLY
with interfaces which has got built-in programmer for Megamos ID48
transponders!
Built-in programmer for Megamos
ID48 transponders! Pre-programming of TP2x transponders as dealer's keys
with component security data which is read from immobiliser!
NEW key programming feature for VAG cars with VDO dashes on CAN bus! (TP2 and UDS protocols)
Note: TP22,23,24,25 transponders are required!
List of supported VAG cars:
Volkswagen
Golf 6, Jetta, Polo, EOS with VDO dash 2009 - 2011, note: not all dashes are supported!
Caddy, Touran, Jetta, EOS with VDO dash 2003 - June.2006
Golf 4, Bora with VDO or Motometer/Bosch dash: 1997-2003
Beetle with Marelli dash: 1998 - 2005
Passat, Jetta, with VDO, Marelli or Motometer dash: 1997-2004
Polo with VDO or Motometer dash: 1999-2006 (1999-2002 mileage change only)
Sharan with VDO dash: 2000-2004(mileage change only)
Caddy, Lupo with VDO or Motometer dash 1997 - 2002(mileage change only)
Transporter with VDO dash 1998 - 2000
LT35 ( Temic immo box) 1999-2003 (pin code read only)
Gol ( Kostal immo box) 1999-2003 (pin code read only)
Seat
Altea, Leon, Toledo with VDO 2003 - 6/2006
Leon, Toledo, Cordoba, Ibiza with VDO or Motometer dash 1997-2003
Alhambra with VDO 2000 - 2004(mileage change only)
Inca with VDO or Motometer 1997 -2000(mileage change only)
Skoda
Octavia II with VDO dash 2005 - 6/2006
Octavia, Fabia with VDO dash 1997 - 2004
Audi
A3 VDO dash 2003 - 2005
A3,A4,A6 VDO dash 1997 - 2000
A3,TT,A6 Magnetti Marelli dash 1998 - 2003
A4 Bosch dash 2000 - 2008 - Read/write of encrypted data with V4.5!
A4,A6,A8 1995-1999 (immo box - read pin code)
Vag tacho usb version 4.52
Vagtcho
4.52 is upgraded from vag tacho usb4.0, Upgrade Vagtacho usb 4.0
interface with Programmer for Megamos ID48 chips, our vagtacho version
5.0 has upgraded directly ,includes the functions for vagtacho usb 4.52
The benefits with this upgrade are:
Your Vagtacho interface will works with software vesrion 5.0 for the new VDO dashes with UDS protocol from year 2009+
Programming of new keys to VAG cars which are into FAZIT database.
Works with cars which has got locked key programming channel, or pin code is not accepted.
No need to wait up to 30 minutes for the key programming procedure.
With this upgrade, Vagtacho can program the new key in one minute
.
Vagtacho version 4.0
VAG Kombiinstrument / Immo box eeprom programmer!
Works on any computer which has got USB port!
Most of VAG dashes from 1997 to 2006 are supported!
Direct programming of Megamos ID48 (JMA-TP08) chips to VAG cars on CAN bus from November 2003 to June 2006
Transponder Maker Pro is required for pre-programming of these chips.
Note: TP22,23,24,25 transponders are NOT required!
1.Main functions:
Read ecu info
Read pin code
Change mileage
Read eeprom
Programmer new key
Write eeprom
Clear ecu errors
Viem memory buffer
2.List of supported VAG cars:
Volkswagen
Caddy, Touran, Jetta, EOS with VDO dash 2003 - June.2006
Golf 4, Bora with VDO or Motometer/Bosch dash: 1997-2003
Beetle with Marelli dash: 1998 - 2005
Passat, Jetta, with VDO, Marelli or Motometer dash: 1997-2004
Polo with VDO or Motometer dash: 1999-2006 (1999-2002 mileage change only)
Sharan with VDO dash: 2000-2004(mileage change only)
Caddy, Lupo with VDO or Motometer dash 1997 - 2002(mileage change only)
Transporter with VDO dash 1998 - 2000
LT35 ( Temic immo box) 1999-2003 (pin code read only)
Gol ( Kostal immo box) 1999-2003 (pin code read only)
Seat
Altea, Leon, Toledo with VDO 2003 - 6/2006
Leon, Toledo, Cordoba, Ibiza with VDO or Motometer dash 1997-2003
Alhambrawith VDO 2000 - 2004(mileage change only)
Inca with VDO or Motometer 1997 -2000(mileage change only)
Skoda
Octavia II with VDO dash 2005 - 6/2006
Octavia, Fabia with VDO dash 1997 - 2004
Audi
A3 VDO dash 2003 - 2005
A3,A4,A6 VDO dash 1997 - 2000
A3,TT,A6 Magnetti Marelli dash 1998 - 2003
A4 Bosch dash 2000 - 2005
A4,A6,A8 1995-1999 (immo box - read pin code)
3. How to programmer keys with vagtacho usb 4.0
Switch ON ignition with any key new or old, no mater which one.
Start software, select "VDO NEW - CAN bus" from menu.
Press "Connect Selected ECU" button, after 5 seconds the data of the dash will be shown on screen.
Press "Program New Key", software will read data from the dash and after few seconds a new window will be open.
See the picture. ID numbers of the transponders which are stored into memory will be shown.
This is TMPro module#146 window. Insert transponder key with new Megamos ID48 chip and program it.
Press
"Add Key" and a message will be shown. Switch ON ignition with key
which you want to program! The key may be new - already programmed with
TM Pro, or old - key which has been used with the same car! Vagtacho
will check the key. If this key is already programmed to the car, or it
is from another car, Vagtacho will show warning message on screen and
won't program this key!
If
everything is ok, Vagtacho will add the new key into the data of
immobilizer and will show ID number of new key on screen. See the red
mark on the picture. Now you are ready to program the new transponder
key into the immobilizer. Press "Write Keys" to complete programming
procedure !
Press
"Write Keys" and the warning window will be open. If you are sure that
everything is all right, press"Continue", otherwise press "Cancel". If
you press "Cancel" nothing will happens, and the data won't be written
into immobiliser. After pressing "Continue" Vagtacho will writes the
data into immobiliser after few seconds. The dash will be reset, and the
programming procedure will be completed!
This
is the last step, after this the new data will be written into
immobiliser! If you have marked and erased some keys, they will NOT
works anymore!
Press
"Write Keys" and the warning window will be open. If you are sure that
everything is all right, press"Continue", otherwise press "Cancel". If
you press "Cancel" nothing will happens, and the data won't be written
into immobiliser. After pressing "Continue" Vagtacho will writes the
data into immobiliser after few seconds. The dash will be reset, and the
programming procedure will be completed!
This
is the last step, after this the new data will be written into
immobiliser! If you have marked and erased some keys, they will NOT
works anymore!
This
picture shows the final Vagtacho window. If you have switched ON
ignition with key which is already programmed by TMPro, the warning lamp
of immobiliser on the dash will be turned off. The new key is already
stored into immobiliser and you can start engine!
If
the immobiliser's warning lamp on the dash is still flashing, there is
some error in programming procedure, you can check the transponder key -
see how to do this on the next picture!
Switch
ON ignition with the key which you want to test! Start software, select
"VDO NEW - CAN bus" from menu, and press"Transponder Check". Vagtacho
will connects immobiliser. Press "Read ECU Info" button, and wait about
10 seconds. The information about this transponder key will be displayed
on screen, see the next picture. You can press "Read ECU Info" to
testing of transponder key again. This procedure is optional, and is not
required when programming the new keys.
Switch
ON ignition with the key which you want to test! Start software, select
"VDO NEW - CAN bus" from menu, and press"Transponder Check". Vagtacho
will connects immobiliser. Press "Read ECU Info" button, and wait about
10 seconds. The information about this transponder key will be displayed
on screen, see the next picture. You can press "Read ECU Info" to
testing of transponder key again. This procedure is optional, and is not
required when programming the new keys
Transponder
variable part and transponder locked must be "YES", otherwise there are
errors in programming of the new key with TMPro!
Transponder
fixed part must be "YES" otherwise the key is still not programmed into
immobiliser, or Vagtacho programming procedure is not completed
successfully. In case of such error, repeat whole programming procedure
again with another new transponder! All parameters must be set "YES"!
the shipping cost.
3. We provide buyer free and unlimited technical support if you have any using problem with our item.
shipping:
1.We ship your orders within 3 business days after the payment is cleared.
2.Item
is shipped via airmail Post. It normally takes 12-15 working day to
worldwide depends on the destination you live.However, for some
countries, such as Italy, Russian, Brazil, France, some remote areas,
etc, it may need 20-50 days (delayed by countries? customs, transit
station, etc).
And international shipping was more complicated and
due to both countries' customs,transit station etc.It may takes longer
time than expected.
If you don't receive the item after the 25 days, please contact us freely, we'll try our best to solve the delivery problem.
3:If the item shipped by DHL, EMS and other express shipping it will reach to you in 3-7 days or 5-10 days.
payment:
We only accept payment through Paypal.
Feedback:
1:
Please give me a fair feedback after completing the transaction. if you
are satisfied with our service, please leave us a positive feedback and
rate the details of the transaction (Detailed Seller Ratings) with a
"PERFECT 5 STARS". When you rate the shipping time part please take
international transit into consideration.
2: If you are not satisfied
with our service,Please email us before leaving any 1 or 2 ratings,
negative feedback or open any dispute.please kindly contact us and give
us a chance to solve this matter to you,We promise we will solve this
matter to you within 2 days.
Other Policies:
1:Emails and messages are answered within 24 hours, Monday to Friday except public holidays
If you do not receive our reply, please kindly re-sent your email and we will reply you as soon as
2:.Serious Buyer Only! Please place bid only if you agree all