MONKEY ECO FRIENDLY DIAMOND STONE POLISHING PAD
** This listing if for 1 pad **
Environmentally Friendly
For Restoration of Marble, Travertine, Limestone and Terrazzo
Revolutionary new method for Non Toxic, Bio Degradable and Chemical Free Honing and Polishing of Marble, Travertine, Limestone and Terrazzo. Easy to use with any 17" 175-300 rpm floor scrubber. These unique pads are washable and re-usable. Each set comes with instructions for proper use.
Technical
Available Sizes; 5, 8, 17, 20, 27
Availables Grits; 200, 400, 800, 1500, 3000, 8000 and 11000
Floor Machines - 17" - 20" (175-350 rpm)
Pads remove wear and provide a variety of appearance levels from dull hone (no shine) to highly polished. Use on floors with little to no lippage (uneven tiles).
Hand Polishers - 5 - 8" Variable Speed (600-3000 rpm)
Pads remove wear and provide a variety of appearance levels from dull hone (no shine) to highly polished. Use on floors, walls and counter tops with little to no lippage (uneven tiles).
Features
- Chemical free Diamond pads are an Eco Friendly way to achieve a dull hone on Travertine, Marble, or Limestone Floors, countertops or walls.
- Use on floors walls or countrtops with little to no lippage (uneven tiles).
- Easy to use, washable and reusable.
- Pads remove wear and provide a variety of appearance levels from dull hone (no shine) to highly polished.
- Safe on all stones and tile, will not damage any stone
- Professional strength formula
- Edge work can be done by using the 5" or 8" pads with a hand tool.
- Read instructions before using
----------------------------------------------------------------------------
Instructions for proper useThese pads are meant to be used to remove wear and achieve a wide variety of finishes from dull hone (no shine) to a high polish on Marble, Travertine or Limestone floors, walls or counter tops with lippage (uneven tiles).
Follow these simple steps to achieve great result with less mess in less time without the use of harsh chemicals.
For use with Floor Machine 17″ and 20″ (175-350 rpm)
1. Sweep or vacuum the surface to remove all abrasive soils.
2. Clean surface with Stone Cleaner.
3. Rinse surface thoroughly.
4. Center “Monkey Pad” on drive plate on floor machine.
5. 175 rpm machines work best with 30 lb drive plate, 300-350 rpm machines do not require extra weight.
6. Apply enough water to 2 ft x 5 ft area to lightly wet the surface. No need for huge puddles.
7. Move the floor machine in and oval pattern (as shown in the picture on the right) counter clockwise to keep the water inside work area.
8. Check surface after 15 – 30 Seconds to see if desired result are achieved.
9. If YES, repeat step 6-8 on the rest of the room one section at the time.
10. Overlap sections by 4 inch to 6 inch to keep an even finish.
11. If NO, repeat step 7 and 8 until desired result with that grit is achieved) usually 15-45 seconds per 2′ x 5′ area).
12. Rinse whole area between grits
13. Rinse pad thoroughly after each use and allow to dry.
14. Repeat steps 6-10 with grits as you go to higher number until desired finish is achieved.
For use with Hand Polisher 5″or 8″ (600-3000 rpm)
1. Sweep or vacuum the surface to remove all abrasive soils.
2. Clean surface with Stone Cleaner.
3. Rinse surface thoroughly.
4. Center “Monkey Pad” on drive plate on hand polisher.
5. Apply enough water to 2 ft x 3 ft area to lightly wet the surface. No need for huge puddles.
6. At lowest speed setting, move tool in an oval pattern (as shown in the picture on the right) counter clockwise to keep the water inside work area.
7. Check surface after 15 – 30 Seconds to see if desired result are achieved.
8. If YES, repeat step 6-8 on the rest of the area one section at the time.
9. Overlap sections by 4 inch to 6 inch to keep an even finish.
10. If NO, repeat step 7 and 8 until desired result with that grit is achieved) usually 15-45 seconds per 2′ x 5′ area).
11. Rinse whole area between grits
12. Rinse pad thoroughly after each use and allow to dry.
13. Repeat steps 6-10 with grits as you go to higher number until desired finish is achieved.
Tips
1. Use more water with lower grits and less water with higher grits.
2. To verify if you are finished with any grit level, follow these steps :
Use pad in one spot for 20-30 seconds and squeegee water back, if it look better than the rest of the area, keep working it.
3. Use more weight or pressure and less water on grit 3,000 and above
ALL PADS ARE COLOR CODED BY GRIT
---------------------------------------------------------------------------
These pads are meant to be used to remove wear and achieve a wide variety of finishes from dull hone (no shine) to a high polish on Marble, Travertine or Limestone floors, walls or counter tops with lippage (uneven tiles).
Follow these simple steps to achieve great result with less mess in less time without the use of harsh chemicals.
For use with Floor Machine 17″ and 20″ (175-350 rpm)
1. Sweep or vacuum the surface to remove all abrasive soils.
2. Clean surface with Stone Cleaner.
3. Rinse surface thoroughly.
4. Center “Monkey Pad” on drive plate on floor machine.
5. 175 rpm machines work best with 30 lb drive plate, 300-350 rpm machines do not require extra weight.
6. Apply enough water to 2 ft x 5 ft area to lightly wet the surface. No need for huge puddles.
7. Move the floor machine in and oval pattern (as shown in the picture on the right) counter clockwise to keep the water inside work area.
8. Check surface after 15 – 30 Seconds to see if desired result are achieved.
9. If YES, repeat step 6-8 on the rest of the room one section at the time.
10. Overlap sections by 4 inch to 6 inch to keep an even finish.
11. If NO, repeat step 7 and 8 until desired result with that grit is achieved) usually 15-45 seconds per 2′ x 5′ area).
12. Rinse whole area between grits
13. Rinse pad thoroughly after each use and allow to dry.
14. Repeat steps 6-10 with grits as you go to higher number until desired finish is achieved.
For use with Hand Polisher 5″or 8″ (600-3000 rpm)
1. Sweep or vacuum the surface to remove all abrasive soils.
2. Clean surface with Stone Cleaner.
3. Rinse surface thoroughly.
4. Center “Monkey Pad” on drive plate on hand polisher.
5. Apply enough water to 2 ft x 3 ft area to lightly wet the surface. No need for huge puddles.
6. At lowest speed setting, move tool in an oval pattern (as shown in the picture on the right) counter clockwise to keep the water inside work area.
7. Check surface after 15 – 30 Seconds to see if desired result are achieved.
8. If YES, repeat step 6-8 on the rest of the area one section at the time.
9. Overlap sections by 4 inch to 6 inch to keep an even finish.
10. If NO, repeat step 7 and 8 until desired result with that grit is achieved) usually 15-45 seconds per 2′ x 5′ area).
11. Rinse whole area between grits
12. Rinse pad thoroughly after each use and allow to dry.
13. Repeat steps 6-10 with grits as you go to higher number until desired finish is achieved.
Tips
1. Use more water with lower grits and less water with higher grits.
2. To verify if you are finished with any grit level, follow these steps :
Use pad in one spot for 20-30 seconds and squeegee water back, if it look better than the rest of the area, keep working it.
3. Use more weight or pressure and less water on grit 3,000 and above
ALL PADS ARE COLOR CODED BY GRIT
---------------------------------------------------------------------------
Instructions for polishing Granite and MarbleFloor Machines
17” – 20” (175-350 rpm)
Pads remove wear and provide a variety of appearance levels from dull hone (no shine) to highly polished. Use on floors with little to no lippage (uneven tiles).
Instructions
- Sweep or vacuum surface to remove abrasive soil
- Clean and rinse surface thoroughly prior to pad use
- Center selected pad on drive plate of floor machine
- Apply water to 2’ x 5’ area to lightly wet the surface – no need for huge puddles
- Move the floor machine in an oval pattern counter clockwise to keep the water inside the work area
- Check surface after 15 – 30 seconds to see if desired results are achieved
- If YES, repeat steps above on the rest of the floor one section at a time
- If NO, repeat polishing process until desired result is achieved (usually 15 – 45 seconds per 2’ x 5’ area)
- If second polishing does not achieve desired results, change pad grit level and repeat process
Hand Polishers
5″ – 8” Variable Speed (600-3000 rpm)
Pads remove wear and provide a variety of appearance levels from dull hone (no shine) to highly polished. Use on floors, walls and counter tops with little to no lippage (uneven tiles).
Instructions
- Dust or vacuum surface to remove abrasive soil
- Clean and rinse surface thoroughly prior to pad use
- Center selected pad on drive plate of hand polisher
- Apply water to 2’x 3’ area to lightly wet the surface – no need for huge puddles
- At lowest speed setting, move the tool in an oval pattern counter clockwise to keep the water inside the work area
- Check surface after 15 – 30 seconds to see if desired results are achieved
- If YES, repeat steps above on the rest of the area one section at a time
- If NO, repeat polishing step until desired result is achieved (usually 15 – 45 seconds per 2’ x 5’ area)
- If second polishing does not achieve desired results, change pad grit level and repeat process
TIPS
- For best results with 175 rpm Floor Machines use a 60 lb drive plate (not necessary for 300 – 350 rpm machines)
- Use more water when using lower grits (200 – 1,500)
- Use more weight (or pressure) and less water on higher grits (3,000 – 11,000)
- Overlap sections by 4”- 6” to keep an even appearance
- Rinse area thoroughly prior to changing grits
- Rinse and allow pad to dry after each use
- Avoid contaminating the Eco Friendly pads by using them only on a clean surface.
- Pad contamination is a major problem. This is how most people ruin the pads; they don’t wear them out.
- Thoroughly clean and rinse the surface to be polished before using the pads.
- Store the pads in the box making sure that the pads are NEVER diamond face to diamond face.
- Stack them with the colored side up.
- It is better to under use the pads than to overuse them.
- Overusing the 200 grit brown EcoPad
, the 400 grit black EcoPad, or 800 grit red EcoPad may result in a textured appearance or the “orange peel” effect. That can only be removed by honing the floor with a resin bond diamond pad. - You only need enough water to keep the surface wet; you don’t need puddles.
- Edge work can be done by using the 5″ or 7″ pads with a hand tool.
----------------------------------------------------------------------------
Floor Machines
17” – 20” (175-350 rpm)
Pads remove wear and provide a variety of appearance levels from dull hone (no shine) to highly polished. Use on floors with little to no lippage (uneven tiles).
Instructions
- Sweep or vacuum surface to remove abrasive soil
- Clean and rinse surface thoroughly prior to pad use
- Center selected pad on drive plate of floor machine
- Apply water to 2’ x 5’ area to lightly wet the surface – no need for huge puddles
- Move the floor machine in an oval pattern counter clockwise to keep the water inside the work area
- Check surface after 15 – 30 seconds to see if desired results are achieved
- If YES, repeat steps above on the rest of the floor one section at a time
- If NO, repeat polishing process until desired result is achieved (usually 15 – 45 seconds per 2’ x 5’ area)
- If second polishing does not achieve desired results, change pad grit level and repeat process
Hand Polishers
5″ – 8” Variable Speed (600-3000 rpm)
Pads remove wear and provide a variety of appearance levels from dull hone (no shine) to highly polished. Use on floors, walls and counter tops with little to no lippage (uneven tiles).
Instructions
- Dust or vacuum surface to remove abrasive soil
- Clean and rinse surface thoroughly prior to pad use
- Center selected pad on drive plate of hand polisher
- Apply water to 2’x 3’ area to lightly wet the surface – no need for huge puddles
- At lowest speed setting, move the tool in an oval pattern counter clockwise to keep the water inside the work area
- Check surface after 15 – 30 seconds to see if desired results are achieved
- If YES, repeat steps above on the rest of the area one section at a time
- If NO, repeat polishing step until desired result is achieved (usually 15 – 45 seconds per 2’ x 5’ area)
- If second polishing does not achieve desired results, change pad grit level and repeat process
TIPS
- For best results with 175 rpm Floor Machines use a 60 lb drive plate (not necessary for 300 – 350 rpm machines)
- Use more water when using lower grits (200 – 1,500)
- Use more weight (or pressure) and less water on higher grits (3,000 – 11,000)
- Overlap sections by 4”- 6” to keep an even appearance
- Rinse area thoroughly prior to changing grits
- Rinse and allow pad to dry after each use
- Avoid contaminating the Eco Friendly pads by using them only on a clean surface.
- Pad contamination is a major problem. This is how most people ruin the pads; they don’t wear them out.
- Thoroughly clean and rinse the surface to be polished before using the pads.
- Store the pads in the box making sure that the pads are NEVER diamond face to diamond face.
- Stack them with the colored side up.
- It is better to under use the pads than to overuse them.
- Overusing the 200 grit brown EcoPad, the 400 grit black EcoPad, or 800 grit red EcoPad may result in a textured appearance or the “orange peel” effect. That can only be removed by honing the floor with a resin bond diamond pad.
- You only need enough water to keep the surface wet; you don’t need puddles.
- Edge work can be done by using the 5″ or 7″ pads with a hand tool.
----------------------------------------------------------------------------
Shipping & Returns
USA SELLER - In stock - Ship Same Day
30 Days money back guarantee
Contact Us
For help of any sort, contact us by selecting 'contact seller' option
Our physical store is open to the public
Mon – Fri 7:00 am – 5:00 pm
Sunday – 8:00 am – 12:00 pm
Visit our store for more products http://stores.ebay.com/FlooringSupplyShop