YOU ARE ORDERING A 5 PIECE FULL SERVICE AND O-RING SEAL KIT
 to conduct A
FULL SERVICE AND UPGRADE
 
  FOR A (7 SERIES / PHOENIX 50) 
EP7 / EX7 / EP7GW 
NOT FOR "77" SERIES PUMPS
 
SOLENOID type WATER PUMP

THIS SERVICE KIT CONSISTS OF THE 4 O-RING SEALS
(The O-rings are made from nitrile rubber (acrylonitrile butadiene terpolymer).and this is NOT the smae service kit as the 5 series pumps)
&
 
a pyrex polished mineral / glass / crystal ball /sphere valve which replaces the rubbish original plastic (delrin) original which simply wears away to pump failure.
 
 
IF YOUR MACHINE SOUNDS LIKE IT'S PUMPING BUT IT'S NOT, YOU DON'T NEED A REPLACEMENT PUMP (WHICH WILL PROBABLY GO THE SAME WAY AFTER A 1000+ MORE CUPS), YOU JUST NEED TO REPLACE THE BALL SEAL / VALVE.
 
PLEASE NOTE
 IF YOUR COFFEE MACHINE PUMP SOUNDS LIKE IT IS WORKING BUT HAS A POOR OR INTERMITTENT OR NO FLOW, THE MOST LIKELY PROBLEM IS THE BALL VALVE.
 
THE  PUMP IS DESIGNED TO EVENTUALLY FAIL AS IT HAS BEEN MANUFACTURED WITH A PLASTIC BALL (INSIDE) WHICH IMMEDIATELY STARTS TO WEAR DOWN WITH USE UNTIL IT IS TOO SMALL TO CLOSE THE SEAL
 
APART FROM ADDING TO THE WORLDS MICRO-PLASTICS PROBLEM WHICH THE PUMPS WITH THE PLASTIC VALVES DO, THERE IS A REAL RISK THAT THESE PLASTIC PARTICLES HAVE BEEN INGESTED BY YOUR COFFEE DRINKERS AND THE JURY IS OUT ON WHAT ADVERSE EFFECT THEY CAN HAVE ON HEALTH.
 
THIS IS A SCIENCE LABORATORY QUALITY MINERAL (GLASS) SPHERE WHICH WILL NOT WEAR AWAY WITH USE AND WILL PROBABLY OUTLAST THE COFFEE MACHINE. WE HAVE THESE IMPORTED FROM A SCIENCE LABORATORY EQUIPMENT SUPPLIER IN SPAIN AND THEY ARE INFINITELY SUPERIOR TO THE DAFT PLASTIC BEADS WHICH HAVE WORN AWAY IN YOUR COFFEE MACHINE PUMP.
 

THE COFFEE MACHINE SUPPLIER ULTIMATELY WANTS YOU TO either:

OR

YOU DON'T NEED TO DO either, IT'S A REALLY SIMPLE DIY REPAIR WHICH WILL MAKE YOU A LITTLE BIT RICHER IN ACTUAL TERMS, BODY AND SOUL.

THIS FIX ALSO TACKLES THAT BIT OF CORPORATE PLANNED OBSOLESCENCE OUTLINED ABOVE.

This is a repair kit which addresses the problem permanently is better than a new pump as there will be no more micro-plastics in your coffees and it will pump more effectively / efficiently.

If you are on a budget, we can supply the glass sphere on it's own at item number 382416920038

THIS (5-piece) KIT INCLUDES:

  1. 1 x PRECISION MADE GLASS BALL / MINERAL SPHERE
  2. 1 X CORRESPONDING PUMP O-RING
  3. 1 x outer solenoid protecting o-ring
  4. 1 x inner o-ring for pump body union
  5. 1 x inner o-ring for outlet pipe

So this is MUCH BETTER THAN A NEW PUMP OR A LIKE FOR LIKE REPAIR, this listing is for a "ONCE ONLY - FIXED FOR GOOD" repair AND A FULL SERVICE WHILE YOU'RE AT IT.

This is an upgrade to a pumping system that will work without valve wear.

You can do this! PLEASE LOOK AT ALL THE PICTURES AS THEY ARE THERE TO GUIDE YOU.

With basic DIY skills, fitting these new valve and o-ring seals is EASY.

 
  1. In most cases, it is advisable to firstly remove the pump from the coffee machine (this is not always necessary, as in some machines, one can access the pump assembly without removing it from the machine)
  2. Remove 2 screws holding the pump to the metal solenoid chassis
  3. Dismantle the pump as in the supporting photos
  4. replace and discard corresponding o-rings
  5. Replace the plastic ball with the new glass sphere
  6. Using a thin coating of vaseline / petroleum jelly to assist you (sliding o-rings into place) re-assemble pump 
n.b. (pay attention to the photos to make sure it is re-assembled properly)
 
Replace pump into coffee machine
 
JOB DONE !
 
Please re-check all the pictures and diagrams before you start the job as they are there to help you .
 
Happy customer message:
 
thank you friend, I received the repair kit to fix my machine and I did everything as and it worked, thanks again for everything you returned part of the happiness of my girl lol

n.b. All measurements are approximate.
   
*******************     

FOR MORE BARGAINS AND INTERESTING ITEMS, PLEASE VISIT OUR STORE FOR A BROWSE AROUND: 

LOVELIFE3BAY

Heart-with shadow

3L

Lovelife3BAY sell quality home improvement products electrical fuses lighting DIY Motorcycle seat cover repair kits architectural furniture lock window door handle hinges brackets brass chrome finishes mesh aluminium upvc pvc insect screen buttons toe-socks plastic electronic plug adapters and fishing tackle. For multiple purchases, a COMBINED POSTAGE INVOICE should be sent automatically.   If you are happy with the invoice please feel free to proceed with payment. If it doesn't happen automatically or there is ANY issue with the automatic invoice, PLEASE WAIT to receive an invoice or contact us BEFORE you make payment.   There are always ways of improving the service quality, and we endeavour to continually improve, so please feel free to tell us how we can. Thank you for your time to read this.   

Our shipping charge includes:   

• collection service to ensure post is collected virtually EVERY working day 

• packaging materials 

• postage/ delivery/ courier  

*******************