Renogy's DC to DC MPPT on-board Battery Charger is designed to give you options! This multi-stage, multi-input battery charger can charge a service battery from a starting battery linked to an alternator or by utilizing solar panels connected directly to the unit. While your vehicle's alternator prioritizes your starting battery, this unit will allow your solar system to charge your service battery first! It's the smart way to keep yourself fully charged and off-grid longer! And with multi-stage charging and multi-chemistry functionality, Renogy's DC to DC MPPT Charger has you covered whether you're using Flooded, Gel, AGM, or Lithium batteries. With RJ45 communication port featured, you can unlock monitoring features exclusively using the BT-2 Bluetooth Module and Renogy DC Home App, control and monitor the device remotely through your phone in real time.
Condition | |
New: | A brand-new, unused, unopened, undamaged item in its original packaging. |
Battery Voltage Range: | 9-16VDC |
Battery Type: | SLD/AGM, GEL, FLD, LI, USER |
Service Battery Charging Mode: | MPPT |
Charging Efficiency: | Up to 97% |
Max. Solar Input Voltage: | 25V |
Maximum Solar Input Power: | 30A: 400W 50A: 660W |
Alternator Input Voltage: | Traditional Alternator: 13.2-16VDC; Smart Alternator (Euro 6): 12-16VDC |
Maximum Alternator Input Power: | 30A: 400W 50A: 660W |
Dimensions: | 244 x 146 x 77 mm |
Weight: | 1.42kg |
Communication Protocol: | RS485 |
DCC30S 12V 30A Dual Input DC to DC Battery Charger with MPPT
System Voltage: | 12VDC | Battery Voltage Range: | 9-16VDC |
Maximum Charging Current: | 30A | Battery Type: | SLD/AGM, GEL, FLD, LI, USER |
Service Battery Charging Mode: | MPPT | Charging Efficiency: | Up to 97% |
Max. Solar Input Voltage: | 25V | Maximum Solar Input Power: | 400W |
Alternator Input Voltage: | Traditional Alternator: 13.2-16VDC Smart Alternator (Euro 6): 12-16VDC | Maximum Alternator Input Power: | 400W |
Self-consumption: | 60mA | Operating Temperature Range: | -35°C~65°C |
Dimensions: | 244 x 146 x 77 mm | Weight: | 1.42 kg |
Communication Protocol: | RS485 | Ground Type: | Negative |
Terminal Size: | M8*1.25 - 14mm | Temperature Compensation: | -3mV/C/2V |
Storage Temperature Range: | -40°C~80°C | Operating / Storage Humidity | 0%-95%, No Condensation |
DCC50S 12V 50A Dual Input DC to DC Battery Charger with MPPT
System Voltage: | 12VDC | Battery Voltage Range: | 9-16VDC |
Maximum Charging Current: | 50A | Battery Type: | SLD/AGM, GEL, FLD, LI, USER |
Service Battery Charging Mode: | MPPT | Charging Efficiency: | Up to 97% |
Max. Solar Input Voltage: | 25V | Maximum Solar Input Power: | 660W |
Alternator Input Voltage: | Traditional Alternator: 13.2-16VDC Smart Alternator (Euro 6): 12-16VDC | Maximum Alternator Input Power: | 660W |
Self-consumption: | 60mA | Operating Temperature Range: | -35°C~65°C |
Dimensions: | 244 x 146 x 77 mm | Weight: | 1.42 kg |
Communication Protocol: | RS485 | Ground Type: | Negative |
Terminal Size: | M8*1.25 - 14mm | Temperature Compensation: | -3mV/C/2V |
Storage Temperature Range: | -40°C~80°C | Operating / Storage Humidity | 0%-95%, No Condensation |
This battery charger is compatible with both traditional and smart alternators. However, since standard/traditional alternator has a fixed voltage when charging, while smart alternator has a controlled charging output based on operating conditions, it is required to connect the charger to the smart alternator through the Vehicle Ignition Port by the IGN Signal Wire comes with the package.
This Renogy's DC to DC MPPT on-board Battery Charger has a built-in Voltage Sensitive Relay (VSR), thanks to which the charger will Trickle Charge the service battery and maintain its fully charged status, and will also Trickle Charge the starting battery via solar panels. The VSR also ensures reliable isolation between the starting battery and service battery, avoiding charging interference.
This controller supports Gel, AGM, Flooded, and Lithium battery, but please make sure to set the correct battery type once it is installed. For battery settings please refer to the Manual Book on page 12&15.
To change the battery type you will need to press the push button that is located on the PV+ and ALT+ side of the DCDC, then continue to press the button and the LED will display different colors with each representing a single type of battery. Please refer to the manual on page 15 for Battery Type LED.
1. Do not reverse the polarity since the reverse polarity of the battery connections can cause injury and damage to the device. 2. When connecting the charger and the battery, make sure the battery poles are clean when connecting the terminals, select a sufficient cross-section for the connection cable, tighten the nuts and bolts with proper torque as loose connections may cause overheating. 3. Be careful not to over-torque the terminals on the DCDC as over-torquing may cause irreparable damage (Do not exceed 16 N-m / 3.3 ft-lb). 4. Use the following cable colors: Red: positive connection Black: negative connection 5. If the battery charger is connected to the starting battery and solar panels at the same time, the maximum input current will be 15A for each; if the battery charger only connects one of the two DC inputs, the maximum input current will be 30A.
AUD 49.99
AUD 59.99 20%off
Free shipping
AUD 37.99
AUD 39.99 5%off
Free shipping
AUD 179.99
AUD 189.99 5%off
Free shipping
AUD 149.99
AUD 159.99 5%off
Free shipping
Accurage description
Reasonable shipping cost
Shipping speed
Communication
Good buying experience with the seller
Renogy 5 paris connectors cable for solar panels pair male/female connector (#283910073936 )
Renogy 5 paris connectors cable for solar panels pair male/female connector (#283910073936 )