M10 Drop In Masonry Concrete Anchor Lipped Zinc

M10, 10mm Internal Thread, Drop In Anchor, Lipped, Zinc - Masonry, Brick, Concrete Expansion Anchor. Fixaball sells M10, Lipped Drop In, Masonry Anchors. Lipped Drop In Anchor A Lipped Drop In Anchor Expansion anchor for fixing materials to all types of masonry, concrete, brick and non-porous stone. An internally threaded socket anchor for use with bolts or threaded rod of any length. Lipped drop in anchors can be accurately set independant of the hole depth and can be used in non-cracked concrete. The lip allows the anchor to sit flush against the surface, preventing the anchor from being inserted too far. Full expansion can be guaranteed by using the correct shouldered setting punch. Orders placed before 2pm are dispatched same day (Mon-Fri). Standard, Free Delivery is Royal Mail, 2nd Class (2-5 days, most likely 2 days). For a faster delivery time, select 1st class or courier at checkout. Please make your 'no. of items' (pack size) and 'quantity' (of packs) selection from the drop down menus. Internal Thread Anchor Hole Size Anchor Length M10 12mm 30mm M10 12mm 40mm Applications: Light to heavy-duty into solid concrete. Mechanical and electrical services Suspension systems (ceilings) Cable Trays Signs Hand rails Advantages: Flush fitting with no protrusion when not in use Shallow embedment, hence less chance of drilling into rebar, and faster drilling Removal of fixture leaves anchor undisturbed Setting tool stamp marks to indicate complete expansion Visual expansion check with setting tool Permanent anchorage point in solid concrete, brick or masonry Can be used with all types of bolts, screws and studs Installation: Drill a hole in the concrete using a hammer drill and a carbide tipped masonry drill bit, matching the bit size with the outside diameter of the drop-in anchor being used. Make sure the hole depth exceeds the minimum embedment (around 5%) Drill the correct diameter hole and depth. Clear the hole of all debris with a brush and blow out pump. Push the anchor into the hole until it is flush with the surface of the concrete. Insert the relevant setting tool of the same diameter as the anchor until it makes contact with the cone. Use a hammer to drive the setting tool into the anchor – stop hammering when the expander shoulder rests against the anchor or when it is blocked (in hard concrete). Tighten to the recommended torque using a torque wrench. Table: Shows important drop-in masonry anchor sizes/ measurements Fixaball Fixings and Fasteners Lipped Drop in Anchors - Important Dimensions Thread Diameter Anchor Hole Size Anchor Length Minimum Hole Depth mm mm mm mm M6 8 25 10 M8 10 30 14 M10 12 30 15 M10 12 40 15 M12 15 50 20 M16 20 65 22 All specifications are true with correct installation Bolt Length: When the drop-in anchor is set flush with the base material, the minimum bolt length required equals the internal thread length of the anchor, plus the thickness of the material to be fastened, plus the thickness of any washers to be used. If the anchor is set deeper into the concrete, adjust the length accordingly, by adding the additional depth to the minimum anchor length. Anchor Spacing: The forces on a Drop-In Anchor are transferred to the material in which it is installed. If the anchors are installed too close together, it can cause an interaction of the forces, thus reducing the holding power of the anchors. Minimum spacing between anchors and minimum edge distances for the concrete drop-in anchor are as follows: Image is for illustrative purposes only.

M10 Drop In Masonry Concrete Anchor Lipped Zinc

M10, 10mm Internal Thread, Drop In Anchor, Lipped, Zinc - Masonry, Brick, Concrete Expansion Anchor.

Fixaball sells M10, Lipped Drop In, Masonry Anchors.

Lipped Drop In Anchor

A Lipped Drop In Anchor Expansion anchor for fixing materials to all types of masonry, concrete, brick and non-porous stone. An internally threaded socket anchor for use with bolts or threaded rod of any length. Lipped drop in anchors can be accurately set independant of the hole depth and can be uséd in non-cracked concrete. The lip allows the anchor to sit flush against the surface, preventing the anchor from being inserted too far. Full expansion can be guaranteed by using the correct shouldered setting punch.

 

Orders placed before 2pm are dispatched same day (Mon-Fri).

Standard, Free Delivery is Royal Mail, 2nd Class (2-5 days, most likely 2 days). For a faster delivery time, select 1st class or courier at checkout. 

Please make your 'no. of items' (pack size) and 'quantity' (of packs) selection from the drop down menus.

 

Internal Thread Anchor Hole Size Anchor Length
M10 12mm 30mm
M10 12mm 40mm


Applications:

  • Light to heavy-duty into solid concrete.
  • Mechanical and electrical services
  • Suspension systems (ceilings)
  • Cable Trays
  • Signs
  • Hand rails

Advantages:

  • Flush fitting with no protrusion when not in use
  • Shallow embedment, hence less chance of drilling into rebar, and faster drilling
  • Removal of fixture leaves anchor undisturbed
  • Setting tool stamp marks to indicate complete expansion
  • Visual expansion check with setting tool
  • Permanent anchorage point in solid concrete, brick or masonry
  • Can be uséd with all types of bolts, screws and studs

 

Installation:

  1. Drill a hole in the concrete using a hammer drill and a carbide tipped masonry drill bit, matching the bit size with the outside diameter of the drop-in anchor being uséd. Make sure the hole depth exceeds the minimum embedment (around 5%)
  2. Drill the correct diameter hole and depth.
  3. Clear the hole of all debris with a brush and blow out pump.
  4. Push the anchor into the hole until it is flush with the surface of the concrete.
  5. Insert the relevant setting tool of the same diameter as the anchor until it makes contact with the cone. Use a hammer to drive the setting tool into the anchor – stop hammering when the expander shoulder rests against the anchor or when it is blocked (in hard concrete).
  6. Tighten to the recommended torque using a torque wrench.

 

Table: Shows important drop-in masonry anchor sizes/ measurements

Fixaball Fixings and Fasteners

Lipped Drop in Anchors - Important Dimensions

Thread Diameter

Anchor Hole Size

Anchor Length

Minimum Hole Depth

mm

mm

mm

mm

M6

8

25

10

M8

10

30

14

M10

12

30

15

M10

12

40

15

M12

15

50

20

M16

20

65

22

 

All specifications are true with correct installation

 

 Bolt Length:

When the drop-in anchor is set flush with the base material, the minimum bolt length required equals the internal thread length of the anchor, plus the thickness of the material to be fastened, plus the thickness of any washers to be uséd.

If the anchor is set deeper into the concrete, adjust the length accordingly, by adding the additional depth to the minimum anchor length.

 

Anchor Spacing:

The forces on a Drop-In Anchor are transferred to the material in which it is installed. If the anchors are installed too close together, it can cause an interaction of the forces, thus reducing the holding power of the anchors. Minimum spacing between anchors and minimum edge distances for the concrete drop-in anchor are as follows:


Image is for illustrative purposes only.

×
×
×
×
×

Tell a friend Visit store Watch now

Postage info

Click the Postage tab above the listing description for more info

Additional delivery notes

PICK UP OPTION

Sorry, our items are NOT available for pick-up.

PAYING VIA PAYPAL


We accept PayPal on our all our items so you can shop with confidence.

Simple choose the PayPal option when proceeding through the checkout.

Paying via Direct Deposit

Simply add the freight cost to the item cost and forward the total amount to the address to be provided following your purchase.

Additional Information

No additional information at this time

Ask seller a question

To contact our Customer Service Team, simply click the button here and our Customer Service team will be happy to assist.

Ask seller a question

© Fixaball

Click the Postage tab above the listing description for more info

Accepted Payment Methods

  • PayPal
  • Direct Deposit

Returns are accepted

Items must be returned within 30 days of the auction ending

Buyer will pay for return shipping.


Additional Information:
Returns 'NO QUIBBLE' Our returns policy lasts 30 days. If 30 days have gone by since delivery, unfortunately we can’t offer you a refund or exchange (+ a couple of days, grace). To be eligible for a return, your item must be unuséd and in the same condition that you received it. It must also be in the original packaging with original documentation. A restocking fee of 15% will be applied to refunds. Cost of sending the shipment is not refunded unless the wrong item was sent. To complete your return, we require a receipt, invoice or other proof of purchase. This will enable an easier process of locating and amending orders. Please keep all labels, stickers and original packaging to be eligible for free returns. Refunds (if applicable) NO QUIBBLE - We invite all people to stay with us as their preferred supplier of fixings and fasteners. If you're not happy, we will do everything possible to help. Please, please, please keep all documents, stickers, labels and packaging; it makes the process run quicker and easier. Orders over £1000 need to be returned within 5 working days to be accepted, processed and refunded. Late or missing refunds (if applicable) If you haven’t received a refund on the day of return please contact us to verify the situation. Banks vary in their reaction time to changes; there is often some processing time before a refund is posted. Any concerns no matter how small, contact: 01242 522244 Sale items (if applicable) Only regular priced items may be refunded, unfortunately sale items cannot be refunded. Exchanges (if applicable) NO QUIBBLE - All exchanges are welcomed, assuming that items are suitable for re-sale. Please, return the item with the invoice and a note describing what you would like as an exchange. AN invoice will be sent to cover the postage to send the exchanged item. Free returns are available in the very rare event that we have sent an incorrect item. Orders over £1000 need to be returned within 5 working days to be accepted, processed and exchanged. Shipping 99% of orders are dispatched the same day as purchase if the order was made before 2pm. After 2pm your order will join the following days post. Royal Mail deliver most items up to 2kgs and Interlink Express deliver our oversized and heavier items, next day. Usually, the easy bit is getting the order out the door, but, what happens after can occasionally disappoint us both. If delivery is crucial/ time sensitive, you should select a faster and/ or signed for postage option at checkout. Mailing Disclaimer 98% (490 orders) of shipping arrives on time. 2% (10 orders) are late 1.4% (7 orders) 1 day late 0.4% (2 orders) 2 days late 0.2% (1 order) 3+ days late 0.01% is reported lost. - 1 every couple of years Our 'NO QUIBBLE' guarantee gives you peace of mind that we will accept all, undamaged returns and issue a refund, every time. If you need a definite arrival time please select an express service at check out to avoid disappointment.