Product Description
Fit Vehicles:
2006-2011 Mercedes-Benz B200 2.0L L4
2006-2011 Mercedes-Benz B200 2.0L L4 Turbocharged
2006-2009 Mercedes-Benz C230 2.5L V6
2010-2011 Mercedes-Benz C250 2.5L V6
2006-2007 Mercedes-Benz C280 3.0L V6
2008-2011 Mercedes-Benz C300 3.0L V6
2006-2011 Mercedes-Benz C350 3.5L V6
2008-2012 Mercedes-Benz C63 AMG 6.3L V8
2006-2009 Mercedes-Benz CLK350 3.5L V6
2007-2009 Mercedes-Benz CLK550 5.5L V8
2007-2008 Mercedes-Benz CLK63 AMG 6.3L V8
2007-2010 Mercedes-Benz CLS550 5.5L V8
2006-2011 Mercedes-Benz E350 3.5L V6
2010-2011 Mercedes-Benz E550 5.5L V8
2007-2012 Mercedes-Benz GL450 4.6L V8
2008-2012 Mercedes-Benz GL550 5.5L V8
2010-2012 Mercedes-Benz GLK350 3.5L V6
2009-2011 Mercedes-Benz ML350 3.5L V6
2005-2006 Mercedes-Benz ML500 5.0L V8
2008-2011 Mercedes-Benz ML550 5.5L V8
2006-2011 Mercedes-Benz R350 3.5L V6
2007-2010 Mercedes-Benz S550 5.5L V8
2007-2012 Mercedes-Benz SL550 5.5L V8
2009-2012 Mercedes-Benz SL63 AMG 6.3L V8
2006-2008 Mercedes-Benz SLK280 3.0L V6
2009-2011 Mercedes-Benz SLK300 3.0L V6
2005-2011 Mercedes-Benz SLK350 3.5L V6
2010-2013 Mercedes-Benz S400 3.5L V6 ELECTRIC/GAS
2008 Mercedes-Benz S450 4.6L V8
2009-2010 VW Routan 3.8L V6
2008-2013 Smart Fortwo 1000cc L3
2013 Smart Fortwo 999cc L3 Turbocharged
2007-2010 Jeep Compass 2.0L L4
2007-2010 Jeep Compass 2.4L L4
2007-2010 Jeep Patriot 2.0L L4
2007-2010 Jeep Patriot 2.4L L4
2007-2010 Jeep Wrangler 3.8L V6
2007-2009 Dodge Caliber 1.8L L4
2007-2010 Dodge Caliber 2.0L L4
2007-2010 Dodge Caliber 2.4L L4
2008-2009 Dodge Caliber 2.4L L4 Turbocharged
2008-2010 Dodge Avenger 2.4L L4
2009-2010 Dodge Journey 2.4L L4
2008-2010 Dodge Grand Caravan 3.3L V6
2008-2010 Dodge Grand Caravan 3.8L V6
Features:
Supplied With a Factory-Fitted Connector for Easy Installation
Precision manufactured with a sensing element incorporating premier technical ceramics
Where are my oxygen sensors located?
Diagnostic Trouble Codes (DTC)
When oxygen sensor failure occurs, a DTC is recorded in the Engine Control Unit (ECU) and a Malfunction Indicator Lamp (MIL) is illuminated on the dash, alerting the driver the vehicle has a problem.
How to replace an oxygen sensor?
1- Disconnect the battery.
2- Locate the sensor connector by following its wires. Disconnect it.?
3- Remove the sensor cable from its clips all along its way to the sensor.
4- A specific 22mm socket with side cut out exists (see below). You can use a spanner instead. Hold it in one hand and give it a firm hit with the other hand. It will then unscrew very easily.
5- Remove the sensor and fit the new one.
6- Re-route the cable carefully and meticulously and fix it at every clip. Reconnect the connector.
7- Reconnect the battery and wait 5 minutes before starting the engine.
Please take a video clip of the voltmeter and contact us if our sensor:
Goes above range between 0.1 and 0.9 volt
Remains below 0.5 volts
Stays fixed at a particular voltage
You're free to choose replacement or refund if our sensor fails to work, in this case.
Q: How do I know the O2 sensor is good or not?
A: The only way to know if the O2 sensor is functioning normally is to check its responsiveness to changes in the air/fuel mixture, by Voltage Measurement or Waveform Simulation.
Use a 10-megaohm digital voltmeter. Hook up the voltmeter's red probe to the sensor's signal wire and the black probe to engine ground. (Use back probe method, DO NOT pierce the wire.) For a good sensor, voltage should fluctuate constantly between 0.1 and 0.9 volts after starting the engine for 2 or 3 minutes.
We would send out within 2 business days usually . If there is any delay, you will be notified immediately via e- mail .
l Items will be shipped to buyer's eBay registered address. Please confirm your address before making payment.
l We will NOT be responsible for any delay during delivery including but not limited to customs postage checking, strike, force majeure etc
Out 30-day Satisfaction Guarantee assures our customers that they will receive all orders promptly and exactly as described. In addition , it allows customers to return new and unused products in their original factory condition for any reason within 30 days from the date of purchase.
Notice:
1.All returns must be pre-approved by Autopartm and have a return merchandise authorization (RMA) number.Unauthorized returns will not be accepted.
2.Buyers are responsible for appropriate packing, returning shipping cost, insurance and returning the item in “new” condition. Used items will not be accepted for return.
3.We will replace the returning item with an identical item, issue a full store credit or a full refund.
There is a difference between Genuine and OEM / OE Supplier brands. A genuine part is a part in the auto manufacturer’s original box with their logo on the box. OEM / OE Supplier is a brand licensed by the vehicle manufacturer and the part will not come with the vehicle manufacturer’s logo on it. OEM / OE Supplier parts are often the same parts you’d get at the dealership, just in a different box. We do not accept returns based solely on where a part is manufactured.