Holybro - Kakute H7 Mini Flight Controller V3 Tekko32 F4 4 in 1 45a, Atltal HV Micro VTX 20x20mm Mini ESC for FPV RC Drones
F4 MCU with BLHELI32 firmware
Maximum PWM output upto 96K (default 48K)
Amperage meter scale ratio has been adjusted to 168.
PWM input, TLM supported
Voltage output (VBAT)
NO output BEC
Supports oneshot / Multishot / Dshot PWM
Supports damped light
Supports 3-6S lipo input
Ext. cap needed for 6s (1000uf 35v for 6s usage.)
Mounting holes: 20x20mm(M3)
Size:30 x 39 mm
Weight: 7.2g
Compatible with all major FPV receivers from vendors such as Fatshark, ImmersionRC, etc.
Supports the standard 40-channel set: band A, B, E, Fatshark, and Raceband.
SmartAudio input allows remote control by the flight controller. Change channel, transmit power, and more from Betaflight OSD, flight controller USB port, Taranis Lua Script, and more.
All parameters are controllable via push-button on the side of the unit, for cases where SmartAudio is not used.
MMCX connector is durable and easy to use. Rated for 100’s of mating cycles. Easy and quick antenna changes. No more ripped-off UFL connectors.
LED indicators for channel, band, and power. Allows easy check of vTX parameters simply by glancing at the quad.
Variable transmit power from 25 mW to 800 mW. Use 25 mW for a race and then easily switch to 800 mW for freestyle.
0.5 mW True Pit Mode allows you to power up safely without the risk of knocking other pilots out of the air.
Built in microphone, so you can listen to your motors while you fly, no matter how far away you fly.
Standard 26mm form factor allows you to mount the Atlatl directly on your flight controller stack.
Output Power: 0.5 mW (pit mode), 25 mW, 200 mW, 500 mW, 800 mW
Audio: 6.5 MHz Mono
Protocol:smart audio2.0
Antenna Connector: MMCX
Input Voltage: 7 to 28 volts (2-6S LiPo)
Dimensions: 30x26mm
Mounting Holes: Standard 20mm square to center of holes (M3)
Weight: 3.6g
SKU20160 Kakute H7 Mini+Tekko32 F4 4in1 mini 45A ESC Stack
1x Kakute H7 Mini STACK
1x Electrolytic capacito: 1000uF 35v *1
1x JST SH 8pin to 8pin 65mm cable *1
1x JST SH 8pin to 8pin 25mm cable *1
1x JST SH 6pin 150mm cable*1 (The cable that goes to the CADDX Vista Air Unit is included.)
1x JST SH 6pin to GH 8pin 150mm cable*1 (The cable that goes to the DJI Air Unit is included.)
1x JST SH 6pin to GH 8pin 80mm cable*1 (The cable that goes to the DJI Air Unit is included.)
SKU20161 Kakute H7 Mini+Tekko32 F4 4in1 mini 45A ESC +Atlatl HV Micro Stack
1x Kakute H7 Mini STACK
1x Electrolytic capacito: 1000uF 35v *1
1x JST SH 8pin to 8pin 65mm cable *1
1x JST SH 8pin to 8pin 25mm cable *1
1x JST SH 6pin 150mm cable*1 ( The cable that goes to the CADDX Vista Air Unit is included.)
1x JST SH 6pin to GH 8pin 150mm cable*1 ( The cable that goes to the DJI Air Unit is included.)
1x JST SH 6pin to GH 8pin 80mm cable*1 ( The cable that goes to the DJI Air Unit is included.)
1x 80mm SMA--MMCX Cable
1x 60mm Antenna
1x 150mm 4pin JST GH wire