eBay

Genuine LMR®-400 Flexible Low Loss Communications Coaxial cable assembly in various lengths - manufactured by Times Microwave Systems and available from McGill Microwave Systems Limited – Authorised Distributor of all Times Microwave Systems products.

Manufactured by Times Microwave Systems(TM) and officially distributed in Europe by McGill Microwave Systems Ltd

Important Alert: There are many "fake" or "alternative" attempted copies of the Times Microwave Systems LMR ® High Performance Coaxial Cable and Connector range - buy only 100% genuine Times Microwave Systems Products - available only here on eBay from an official UK Authorised Distributor.

**Important Note - This is a custom, made to order cable assembly. For this reason, the goods cannot be returned for a refund unless faulty. It is therefore important to ensure the cable assembly is the correct length and has the correct connectors for your exact requirement. Please only proceed to purchase once you are 100% sure this is the correct cable assembly for your application**

LMR®-400 Flexible Low Loss Communications Coaxial Cable is ideal for:

Drop-in replacement with up to 40% Lower Attenuation for RG-8 , RG 213 ,RG 214 and 9913 Air-Dielectric type Cables
Jumper Assemblies in Wireless Communications Systems
Short Antenna Feeder runs
Any application (e.g. WLL, GPS, LMR, WLAN, WISP, WiMAX, SCADA, Mobile Antennas, Sat Comms , Radio Amateur ,PMR 2 way Radio) requiring an easily routed, low loss high performance RF cable
3G or 4G repeaters
Radio antennas or receivers

Attenuation dB figures per 100m

30 MHz : 2.2dB

50 MHz : 2.9dB

150 MHz : 5.0dB

220 MHz : 6.1dB

450 MHz : 8.9dB

900 MHz : 12.8dB

1500 MHz : 16.8dB

2500 MHz : 22.2dB

Temperature range: -40⁰C - +85⁰C

Inner Conductor: Solid BCCAI (2.74mm)

Dielectric: Foam PE (7.24mm)

Outer conductor: Aluminium tape (7.39mm)

Overall Braid: Tinned copper (8.13mm)

Jacket: Black PE

Mechanical Specifications

Bend Radius: installation 25.4mm

Bend Radius: repeated 101.6mm

Bending Moment: 0.68Nm

Weight lb/ft 0.10 Kg/M

Tensile Strength 72.6 Kg

Flat Plate Crush: 0.71Kg/mm

All Assemblies are custom made to order, We can supply and assemble any size cable and connectors, If you cant find what your looking for please message us and we’ll be happy to help with your requirements.

Helium miner and required cable connector

Helium miner type	Required connector type to meet miner LoRaWAN interface
Bobcat Bobcat 300	RP SMA MALE
RAKwireless/MNTD RAK V2	RP SMA MALE
NEBRA Indoor	RP SMA MALE
NEBRA Outdoor	N MALE
SyncroB.it	SMA MALE
LongAP ONE	SMA MALE
LongAP Pro	N MALE
LongAP Light	SMA MALE
Original Helium (First 700 Hotspots)	SMA MALE
Sensecap M1	RP SMA MALE
Clodpi Pro hotspot	SMA MALE
Controllino	SMA MALE
FXTec Linxdot	RP SMA MALE
Heltec indoor hotspot	RP SMA MALE
Kerlink	RP SMA MALE
Dragino	SMA MALE

*The table above indicates which type of connector your cable must have to allow it to connect to the relevant Helium miner*

This Assembly comes with N Female and SMA RP Male connectors installed on each end.

LMR® is a registered trademark of Times Microwave Systems