Bond It Clear HA6 RTV Silicone Sealant Marine Aquarium Safe Water Fish Tank
![](https://d3d71ba2asa5oz.cloudfront.net/72001479/images/ha6%20clear.jpg)
![](https://d3d71ba2asa5oz.cloudfront.net/72001479/images/ha6%20insitu1.jpg)
![](https://d3d71ba2asa5oz.cloudfront.net/72001479/images/ha6%20insitu2.jpg)
![](https://d3d71ba2asa5oz.cloudfront.net/72001479/images/ha6inmsitu3.png)
![](https://d3d71ba2asa5oz.cloudfront.net/72001479/images/bond%20it%20logo.jpg)
A high quality, non‐shrinking, marine quality, automotive silicone sealant. Surpasses the requirements of EN15651‐1,2:2012.
- Unaffected by UV, ozone, salt water immersion and extremes of temperature
- Non-slumping in paste form
- Recommended for bonding, bedding and sealing glass in aquarium construction
- Recommended for the manufacture of in-situ gaskets and seals for pumps and pipework to prevent water ingression
- It is ideal for use on: glass; ceramics; anodised aluminium; primed metals and timber and many plastics
HA6 is a high quality, non‐shrinking, marine quality, automotive silicone sealant. Surpasses the requirements of EN15651‐1,2:2012.
Uses
HA6 is unaffected by UV, ozone, salt water immersion and extremes of temperature and is non-slumping in paste form.
HA6 contains no fungicides or oils which may leach into water and is therefore recommended for bonding, bedding and sealing glass in aquarium construction.
HA6 is also recommended for the manufacture of in-situ gaskets and seals for pumps and pipework to prevent water ingression and as a dust and weatherproofing seal for cabinets in dirty environments or external applications.
It is ideal for use on: glass; ceramics; anodised aluminium; primed metals and timber and many plastics.
Preparation
Ensure all surfaces are clean, dry and free from grease, oil or any other contaminants that may hinder adhesion. Prime porous surfaces and metals other than anodised aluminium or stainless steel for optimum adhesion.
Application
Apply using a standard sealant gun with the nozzle cut at an angle of 45°, and to an opening slightly larger than the joint to be sealed.
For sealing and bedding apply in the normal fashion and tool to a smooth finish one or two minutes after gunning.
As an adhesive bring the two surfaces together before skinning commences and do not stress the joint before the silicone has developed strength.
As a gasket apply to one surface and if the joint is to be broken allow a strong skin to develop before compressing for permanent gaskets the joint can be sealed immediately. Clean away any excess with white spirit.
When using in aquarium assembly please refer to separate sheet for instructions which can be supplied upon request.
Limitations
Not suitable for use on bitumen, asphalt, natural stone or unprimed metals.
Do not use as a mirror adhesive,
Do not apply at temperatures below 5C or above 30C.
Colour
HA6 comes in 4 colours: white, translucent, black and grey.
Container Size
310ml plastic cartridge.
Shelf Life
24 months from date of manufacture when stored in original unopened cartridges.
Storage Conditions
Store in cool, dry conditions at a temperature between 5 and 25 C.
Disposal of Containers
Do not leave empty containers where residue could be harmful to children, animals or the environment. Remove any containers to a central disposal point in accordance with local regulations.
Health & Safety
Please refer to separate material safety data sheet for full
handling, use and storage instructions (available on request).
Keep out of reach of children. It is the users responsibility to determine suitability for use.
If in doubt contact our Technical Department for advice.
Note: this information is for general guidance only, since site conditions and labour are beyond our control. It is recommended that users make their own tests to determine suitability.
Specification Summary
Flammability Non-flammable
Tooling Time 5-10 minutes
Tack Free 10-20 minutes
Full Cure 3mm depth per day
Application Temperature +5o C to +30o C
Rubber Hardness Shore A: <25
Maximum Extensibility 300%
Joint Movement Capability 25% by ISO methods
Service Temperature Limits -60o C to +180oC. Short periods over
200o C are not detrimental to sealant performance