Features:
- Fitment - This Float Switch Connector is compatible with Hoshizaki KM-1300, KM-1340, KM-1600, KM-1601,KM-280, KM-320, KM-320MAH, KM-500, KM-501, KM-515, KM-515MAH,KM-650, KM-800, KM-900, KM-901.(Please Check Manuals Before Ordering)
- Function - It is a float switch that is used to detect the level of water in the machine's reservoir. The float switch is mounted on the side of the reservoir and consists of a plastic boot with a metal float inside. The float moves up and down with the water level, activating or deactivating the switch as needed. When the water level drops below a certain point, the switch will activate and signal for more water to be added to the reservoir. This helps ensure that there is always enough water in the machine to make ice.
- Easy to Install - To replace the float switch in an ice machine, first, turn off the power and remove the front panel. Locate the existing float switch and disconnect its wires before removing it from the mounting bracket. Install the new float switch securely on the bracket and connect the wires to their respective terminals, ensuring they are firmly attached. Replace the front panel, turn on the power, and test the new float switch by placing a container of water under the drain line.
- Replace Part# - 426799-01.
- Guarantee - We are confident in the quality of our products and offer a 30-day money-back guarantee. If you are not 100% satisfied with our products, simply return it for a full refund. Additionally, we offer premium support and a 1-year warranty for your peace of mind.
Descriptions:
This Float Switch Connector is compatible with Hoshizaki KM-1300, KM-1340, KM-1600, KM-1601,KM-280, KM-320, KM-320MAH, KM-500, KM-501, KM-515, KM-515MAH,KM-650, KM-800, KM-900, KM-901.(Please Check Manuals Before Ordering)
Easy to install:
1. Turn off the power supply.
2. Remove the front panel, then move the control switch to the “OFF” position.
3. Drain the water tank.
A) On KM-320M_H, KM-515M_H, KM-600M_H, KM-650M_H, and KM 901M_H, remove the base cover, then
disconnect one end of the pump tubing to drain the water tank (See Fig. 1). After the water tank has drained,
reconnect the pump tubing.
B) On KM-1340M_H and KM-1601M_H, remove the rubber cap covering the overflow pipe in the water tank.
Remove the overflow pipe by turning it counterclockwise. After the water tank has drained, replace the overflow
pipe and the rubber cap in their correct positions. Note: Be sure the overflow pipe o-ring is in its correct position
on the overflow pipe.
4. Disconnect the vent tube and the flush tube from the top of float switch, then remove float switch assembly and
remove the old rubber boot from the bottom of float switch assembly (See Fig. 2). Discard the old rubber boot.
5. Remove the retainer rod from the bottom of float switch housing, then remove the float. Be careful not to bend
the retainer rod excessively when removing it.
6. Wipe down float switch housing, shaft, float, and retainer rod with a mixture of 1 part “ScaleAway” and 25 parts
warm water. Clean the inside of the new rubber boot and hose with cleaning solution. Rinse the parts thoroughly
with clean water.
7. Reassemble float switch assembly and replace it and the new rubber boot in their correct positions. Reconnect
the vent tube and the flush tube.
8. Move the control switch to the “ICE” position.
9. Replace the base cover (if applicable) and front panel in their correct positions.
10. Turn on the power supply to start the automatic icemaking process.
Package Includes:
1* 426799-01 Float switch connector
Feedback is very important to us.
or Negative
feedback. i will do my best to solve the problem, thanks!