Touch-up pen suitable for Mercedes, 197 or 9197 obsidian black metallic, 2 in 1



Touch-up pen suitable for Mercedes + 2 free paint swabs and instructions for use

Hue: 197 or 9197 Obsidian Black Metallic

 

 Characteristics:

· Weather-resistant, lightfast and non-yellowing

· High yield due to higher pigmentation

· Highest filling power and opacity

· Very good adhesion and brilliant colors

· 2 in 1, the touch-up stick can be used with the integrated brush and to carry out precise work you can simply use the fine paint tip to fill in stone chips, for example

 

Scope of delivery:

1 paint pen as stated above with 10ml, undiluted, with screw cap and mixing ball, integrated brush and fine paint tip to touch up stone chips


2 paint swabs (the color of the paint swabs may vary)


1 free application guide 

 

Shipment:

Shipping is usually as a maxi letter with Deutsche Post (within Germany). The base of the touch-up pen is removed for transport security when shipped. You can easily put it back on.

 

Repair scratches - how do I proceed?

 

  1. Thoroughly clean the area, if rust is visible remove it carefully with sandpaper (please make sure that the surrounding paintwork is not damaged).
  2. For bare plastic parts, we recommend using a plastic adhesive primer, which is applied very thinly to the bare plastic and approx. Leave for 10 to 15 minutes. You can find the plastic adhesive primer in our shop.
  3. Shake the 1K primer/rust protection paint stick (if necessary) vigorously and apply very carefully with the brush and allow to dry (approx. 10 to 15 minutes should usually be enough ).
  4. Then shake the base coat touch-up pen vigorously and carefully apply a thin layer in several layers, leaving it to dry again and again (approx. 10 to 20 mins. ), repeat the whole thing until the base coat has covered, then again for approx. Leave to dry for 15-20 minutes.
  5. Then shake the clear coat touch-up stick vigorously and apply carefully, then let it dry properly. The clear coat is usually more viscous than the base coat, so it should be used more sparingly.

 

 A notice:
All paint sticks are always checked by us for quality and consistency.

Color deviations of the touch-up pen compared to your vehicle are possible due to the age of the vehicle and the weather.

Remark: Be sure to protect from frost! Repairing the damaged car paint using our touch-up pen cannot replace a professional repair in a car paint shop! No liability for improper use.


link to Online dispute resolution platform of the EUtarget="_blank"


danger sign

 

  

        

hazard warnings

 

H225 Highly flammable liquid and vapour.

H315 Causes skin irritation.

H319 Causes serious eye irritation.

H336 May cause drowsiness and dizziness.

H373 May cause damage to organs through prolonged or repeated exposure.

 

safety instructions

 

P101 If medical advice is needed, have product container or label at hand.

P102 Keep out of the reach of children.

P103 Read label before use.

P210 Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. Do not smoke.

P260 Do not breathe dust/fume/gas/mist/vapours/spray.

P280 Wear protective gloves/protective clothing/eye protection/face protection.

P303+P361+P353 In case of contact with skin (or hair): Take off immediately all contaminated clothing. 

Rinse skin with water/shower.

P305+P351+P338 In case of contact with the eyes: Rinse cautiously with water for several minutes. If possible, remove contact lenses. Continue rinsing.

P312 If you feel unwell Poison Information Center/Doctor call up.

P337+P313 If eye irritation persists: Get medical advice/attention.

P501 Dispose of contents/container in accordance with local/regional/national/international regulations.

 

KEEP OUT OF THE HANDS OF CHILDREN!


For bare plastic parts, we recommend using a plastic adhesive primer, which is applied very thinly to the bare plastic and approx. Leave for 10 to 15 minutes. You can find the plastic adhesive primer in our shop. Then shake the base coat touch-up pen vigorously and carefully apply a thin layer in several layers, leaving it to dry again and again (approx. 10 to 20 mins. ), repeat the whole thing until the base coat has covered, then again for approx. Leave to dry for 15-20 minutes. Then shake the clear coat touch-up stick vigorously and apply carefully, then let it dry properly. The clear coat is usually more viscous than the base coat, so it should be used more sparingly. I hereby confirm that I am familiar with the legal situation of the ChemVOCFarbV and that I have been sufficiently info
For bare plastic parts, we recommend using a plastic adhesive primer, which is applied very thinly to the bare plastic and approx. Leave for 10 to 15 minutes. You can find the plastic adhesive primer in our shop. Then shake the base coat touch-up pen vigorously and carefully apply a thin layer in several layers, leaving it to dry again and again (approx. 10 to 20 mins. ), repeat the whole thing until the base coat has covered, then again for approx. Leave to dry for 15-20 minutes. Then shake the clear coat touch-up stick vigorously and apply carefully, then let it dry properly. The clear coat is usually more viscous than the base coat, so it should be used more sparingly. I hereby confirm that I am familiar with the legal situation of the ChemVOCFarbV and that I have been sufficiently info