SHAFTSTIK® Golf Club Re-Shafting Kit (10 Clubs)
Everything you need to re-shaft up to 10 Clubs.
SHAFTSTIK® Golf Club Re-Shafting Kit includes the following:
Items Specifications and instructions:
SHAFTSTIK® ‘DON’T LOSE YOUR HEAD SHAFTING GLUE’ is a two-part fast setting ‘high impact’ toughened’ adhesive developed specifically for use to with a wide variety of substrates such as steel golf club shafts, graphite golf shafts and other materials associated with golf club components.
Professional’s and Custom-Fit Workshops use this every day for building golf clubs. It has been tried, tested, and improved over many years and has sold over 1m+ units worldwide. The formula makes this one of the best solutions for golf club shafting available.
It cures rapidly at room temperature within 5 minutes and gives a handling strength in approximately 8 minutes, allowing you to handle the club with confidence after a short period of time.
30-60 minutes gives you an ideal working time, allowing you to work on the golf club as required, such as re-gripping, painting and making loft and lie adjustments without sacrificing valuable workshop time or overall strength of the bond.
24 hours gives you a full cure and the strongest ‘high impact’ and truly ‘toughened’ golf club shafting glue, that is highly recommended for golf club re-shafting.
(Faster full curing shafting glue is not recommended by most Professionals club makers and epoxy resin engineers due to the nature and stress involved when hitting golf balls, the longer the full curing time the stronger the bond).
‘So don’t lose your head’ and use SHAFTSTIK with the upmost confidence!
Typical Curing Properties
Mix ratio by volume 1:1
Maximum gap fill 2 mm
Usable / pot life @23°C 3-4 mins
Handling time @23°C 5-8 mins
Working strength @23°C 30-60 mins
Full cure @23°C 24 hours
Dries Clear
An increase of 8°C in temperature will halve the cure time. Lower temperatures will result in a slower cure time.
Golf Club Preparation: Surfaces/Hosels/Shafts should be clean, dry and grease-free before applying the adhesive. Use a suitable solvent (such as acetone or isopropanol) for the degreasing of surfaces if required. Most shafts/hosels and surfaces will benefit from light abrasion with emery cloth (or similar), to remove any oxide layer and provide a better bond.
Directions for Use: 1. Dual cartridges: Remove the cartridge cap and dispense epoxy until both sides are flowing. 2. Mix equal amounts. 3. Apply the epoxy to one or both components. 4. Join the parts and apply a firm pressure, secure components if possible. 5. Parts must be joined within 3-4 minutes of mixing the two epoxy components. 6. Large quantities and/or higher temperature will decrease the usable mix time life. 7. Full cure will be obtained after 24 hours at 25°C (77°F). Heat can be used to accelerate the curing process but always remember the saying in club making ‘longer is stronger’.
Safety Guidelines:
Use in accordance with the safety data sheet (provided on request) and/or the guidelines as per the label/s on the product. For further assistance with this product call our helpline on +44 (1952 743 038).
Shelf life and Storage Store in a cool dry place in an airtight container and replace cap straight after use, always keep upright when storing. Follow all the guidelines within the safety data sheet (available on request). If stored correctly this product has a shelf life for a period of 6 months.
SHAFTSTIK® 'Don't lose your head' Golf Shafting Glass Beads
SHAFTSTIK Golf Shafting Glass Beads can be added to any of the SHAFTSTIK® two-part epoxies when you have a loose-fitting shaft or wanting to increase the strength of the fit.
By adding a small amount when mixing the epoxy, it will assist in keeping the shaft centered and add to the mechanical and structural strength of the bond.
SHAFTSTIK Golf Glass Shafting Beads are .002” glass oxide granules that are helpful in stabilising and properly centering the shaft in the hosel of the club-head.
SHAFTSTIK Golf Glass Shafting Beads can help increase the viscosity, cushions impact, increases structural and mechanical strength while also reducing shaft tip breakages.
DO NOT exceed 2% to 4% mix ratio of SHAFTSTIK Golf Shafting Glass Beads to SHAFTSTIK® epoxy.
SHAFTSTIK Golf Shafting Beads come in two sizes:
Features and Benefits:
Increases strength of fit.
Keeps golf shaft centered.
Adds to the mechanical structure to the overall bond.
Stabilises the overall fit.
Cushions Impact
Reduces tip breakage.
Directions:
Add the Glass Beads to the epoxy prior to mixing parts A and B.
Mix two-part epoxy and add a recommended mix ratio of 2% Glass Beads to 98% epoxy.
DO NOT exceed 4% to 96% Epoxy as this may compromise the bond.
DO NOT remix.
Follow all Epoxy instructions when mixing.
Safety Guidelines:
Avoid contact with eyes, wash thoroughly if contact is made.
Wash thoroughly with soap and water if contact is made with skin.
If swallowed seek medical advice.
Keep away from children.
Use in accordance with the safety data sheet (provided on request) and/or the guidelines as per the label/s on the product. For further assistance with this product call our helpline on +44 (1952 743 038).
Shelf life and Storage Store in a cool dry place in an airtight container and replace cap straight after use, always keep upright when storing. Follow all the guidelines within the safety data sheet (available on request). If stored correctly this product has a shelf life for a period of 12 months.
SHAFTSTIK® Golf Glue Epoxy Adhesive Mixing Sticks & Boards
SHAFTSTIK Golf Glue Mixing Sticks are ideal for mixing all glues, adhesives, and epoxy resins. When mixing a two-part A and B part epoxy our mixing sticks are ideal.
The mixing sticks can be used in conjunction with SHAFTSTIK Golf Glass Beads when adding or mixing them with a two-part epoxy.
The mixing sticks are the correct size to fit easily into most golf club hosels, allowing an even and correct amount of epoxy to be added to the hosel with minimum over spill or mess.
SHAFTSTIK Golf Glue Epoxy Adhesive Mixing Cards are an ideal solution to mix your glue, adhesive and epoxy resins. They can be re-used and disposed of when finished along with the mixing sticks.
Made from a premium 350gsm grade card with gloss laminated finish to the mixing side, allowing for a smooth mix and minimum epoxy waste left on the card.
SHAFTSTIK Custom-fit Workshop Specification Cards are on the reverse side of the mixing card. Our custom-fit specification card allows you to record golf club equipment data for all individual golf clubs.
Details such as shaft flex, grip size, clubhead loft and lie recordings and swing weight. An ideal way of recording your customers or you own golf club specifications before and after adjustments.
Use in accordance with the safety data sheet (provided on request) and/or the guidelines as per the label/s on the product. For further assistance with this product call our helpline on +44 (1952 743 038).
SHAFTSTIK Premium Grade Grit Sandpaper Strip (for shaft tip and hosel preparation).
About:
The development, manufacturing and engineering of the adhesives, glues, and epoxy resins used spans four decades and three continents, of which is backed up by a high-tech ISO certified production plant and high-grade manufacturing and research and development facility, with expertise of the highest level.
www.shaftstik.com