Feature:

1. Easy Operation: 1 click measurement operation, automatic delayed shutdown. The shutdown current is only 20nA and supports battery power supply. Automatic detection of PNP and NPN bipolar transistors, N, P channel MOSFETs, JFET field effect transistor, diodes, diode, thyristors, resistors, capacitors, inductors. Automatically detect pin definitions.
2. Smart Measurement: Measure the current amplification coefficient B of the bipolar transistor and the conduction voltage Uf of the emission junction. The amplification coefficient of transistors can be identified by high threshold voltage and high current.
3. Clear Display: Can detect the internal protection diodes of bipolar transistors and MOSFETs and display them on the screen. Measure the threshold voltage and gate capacitance of MOSFETs.
4. The Using Tips: Supports two resistance measurements and can measure potential. If the potentiometer is set to the bottom, the tester cannot distinguish between the middle and both ends of the pin.
5. High Accuracy: The resistance measurement resolution is 0.1 ohms, with a maximum measurement value of 50M ohms. The capacitance measurement range is from 25pf to 100mF, that is, 100000 UF. The resolution can get to 1 pF, and the inductance measurement range is 0.01MH‑20H. Otherwise, it will be displayed as resistance. If the inductance DC resistance is higher than 2100, it will also be displayed as resistance.
6. Reliable Work: Can detect the equivalent series resistance ESR of capacitors above 2UF with a resolution of 0.01 ohm. This characteristic is very important for detecting the performance of capacitors. It can display symbols for the correct direction of two diodes and also display forward voltage drop.
7. Quick Response: LED detects whether the forward voltage drop of the diode is higher than normal. Dual LED detection is a dual diode. When the LED is detected at the same time, it will flash. Each test takes approximately two seconds, and only large capacitance and inductance measurements will require a longer time.

Specification:

Item Type: Transistor Tester
Model: MG328
Material: PCB
Display: 12864 LCD Display
Power Supply: 1 x 3.7V AA lithium battery power supply or direct power supply with micro USB interface, shipped without battery.
Features:
1. Using microcontroller.
2. 12864 graphical LCD display of test results.
3. 1 click operation, automatic power off.
4. With power switch to avoid battery consumption during storage and shutdown.
5. Automatic detection of PNP and NPN bipolar transistors, N and P channel MOSFETs, JFET field effect transistor, diodes, double diodes, silicon controlled rectifier, resistance, capacitance, inductance. Automatically detect pin definitions.
6. Measure the current amplification coefficient B and conduction voltage Uf of the bipolar transistor. And some transistors can be identified by high threshold voltage and high current amplification coefficient.
7. It can detect the protection diodes inside bipolar transistors and MOSFETs and display them on the screen.
8. Measure the threshold voltage and gate capacitance value of MOSFETs.
9. It supports the measurement of two resistances, and the potentiometer can also measure. If the potentiometer is adjusted to one end of it, the tester cannot distinguish between the pins in the middle and at both ends.
10. The resolution of resistance measurement is 0.1 ohms, with a maximum measurement value of 50M ohms.
11. The capacitance measurement range ranges from 25pf to 100mF, that is, 100000 UF. The resolution can get to 1 pF, and the inductance measurement range is 0.01MH-20H. Otherwise, it will be displayed as resistance. If the DC resistance value of the inductance is higher than 2100 ohms, it will also be displayed as resistance.
12. It can detect the equivalent series resistance ESR of capacitors above 2UF with a resolution of 0.01 ohm. This function is very important for detecting capacitor performance.
13. It is possible to display symbols in the correct direction for both diodes, while also displaying forward voltage drop.
14. LED detection is a diode, and the forward voltage drop is higher than normal. Double light emitting diodes are detected as double diodes. At the same time of detection, the LED will flash.
15. The time for each test is about two seconds, and only large capacitance and inductance measurements will require a longer time. 

Package List:

1 x Transistor Tester

3 x Crocodile Clip