NVX VSP68 + Free NVX 6x8 Speaker Baffles and Sound Deadening
(600W Max) V-Series 5" x 7" / 6" x 8" 2-Way Coaxial Car Audio Speakers
0
1
2
3
4
5
6
7
8
9
10
11
12
13
NVX VSP68
(600W Max) V-Series 5" x 7" / 6" x 8" 2-Way Coaxial Car Audio Speakers
Quantity: 2
Product Details:
- 5" x 7" / 6" x 8" V-Series Coaxial Car Speakers
- Power Handling:
- Peak: 600 watts per pair / 300 watts each
- RMS: 200 watts per pair / 100 watts each
- Lightweight polypropylene cone provides accurate mid and low notes
- Nitrile Butadiene rubber surround supports linear movement for optimal accuracy
- 25mm Silk dome tweeter delivers rich, warm treble with remarkable clarity and definition
- Stamped steel basket for a sturdy foundation
- Y30 Ferrite motor structure maintains exceptional control over the driver for tight, crisp reproduction
- High temperature TSV voice coil provides superior current distribution while effectively dissipating heat
- 4 Ohms impedance
- Frequency Response: 70-20,000 Hz
- Top-mount Depth: 2-5/8"
- Sensitivity: 89dB
- Authorized Internet Dealer
- 1-year Manufacturer's Warranty
Priced Per Pair
NVX XBAF68 Speaker Baffle Ring Kit
Foldable silicone 6x8" speaker baffle with egg crate foam, one pair/box
Quantity: 2
Product Details
- Foldable Silicone with egg crate foam
- Foldable rings allows for perfect fitment at varying depths
- Creates a tight seal around your speaker for optimum sound quality
- Compatible with 6x8" speakers
- Reduce door panel vibration
- Easy Installation with minimal trimming or cutting
- Waterproof material
- The foam baffles from the competitors will deteriorate over time, while the silicon XBAF65's will last a lifetime
- Authorized Internet Dealer
- 1-year Manufacturer's Warranty
NVX SDSK2 - 90mil 2.3mm THICK
Speaker Kit - 1.38 Square Feet of Sound Damping (Sound Deadening) Material (Two 10" x 10" Pieces)
Quantity: 1
Product Features
- Two 10" x 10" Pieces of Sound Dampening Material
- 90.55mil thick (2.3mm)! There are cheaper, inferior solutions at 50-80mil, but we do not recommend that thin of a solution as it will not perform as well.
- Great sound damping for installing with car door speakers
- 1.38 Square feet total
- Made from 100% Butyl Rubber
- Eliminates road noise
- Quiets vibrations
- Increases sound quality and output of car audio system
- Stops rattles
- Increases SPL
- Reduces heat
- Easy to form aluminum conforms to desired area of vehicle with ease
- Four step peel and stick design for easy installation
- Up to 30% thicker than the leading competitors
- Dimensions (each piece): 10"L x 10"W
- Authorized Internet Dealer
- 1-year Manufacturer's Warranty
How to Install Sound Damping Properly
Sound damping can be a very beneficial accessory to reduce noise and vibration. To take full advantage of this soundproofing, read these instructions carefully and follow them till the end. Itâs important to familiarize yourself with all the details to install the sound damping correctly. Incorrect installation will result in less than desirable results.
Step #1
The first step is to decide which location in your car you want to insulate. These locations include the floorboards, roof, door panels, trunk or firewall. We recommend soundproofing all metal surfaces for maximum sound deadening performance. Next, refer to your vehicleâs service manual for information on how to dismantle the trimming panels. Be careful when removing the panels to avoid breaking the fixing clips.
Step #2
Once the trimming is dismantled, remove the remainder of the factory insulation if it is damaged. If it is still intact, there is no need to permanently remove it. Next, you need to properly clean, dry and degrease the prospective surface. Sound deadening won't adhere properly if applied to a wet or dirty surface. Use a metal surface cleaner or degreaser along with a dry, clean rag. Make sure to use gloves and apply the degreaser in a well-ventilated space.
Step #3
For this step, measure the prospective surface you are going to treat. To make things easier, make a template of the appropriate size on a large sheet of paper and then transfer it to the damping material. That will make it easier to install it more accurately and avoid wasting material. Use a utility knife to cut the desired shape and size. Be careful and use gloves to protect your hands.
Step #4
Place a sheet of sound damping to the surface without removing the protective film. If it covers the surface properly, you are ready to install it. Gradually remove the protective paper film as you apply it to the surface for better adhesion. Once on the surface, press it down firmly until it is set in place. Flatten it with your hands to avoid unnecessary air bubbles. Use a rolling tool like the NVX SDRLR1 to press the mat down to the metal surface. Go across the entire surface with the roller to ensure that the sheet is installed properly.
Step #5
Once all sound deadening is in place, simply reinstall all trim pieces and carpet back to its original placement. Now you are ready to enjoy higher sound quality with fewer vibrations.
International customers are responsible for any and all customs, import duties, brokerage fees, and taxes. They are not included in the item price or stated shipping charges.
Additional shipping fees are required for locations including, but not limited to: PO Boxes, APO/FPO locations, Alaska, Hawaii, Puerto Rico, Guam, Canada and other countries outside the USA.
Product Summary
Manufacturer:
Model number:
VSP68x2, XBAF68x2
Weight:
16.80 lbs
Internal SKU:
vsp68x2_xbaf68x2
Internal Product ID:
181773
