This is a brand new pair of Spread Beam Hi / Low head light inserts and our premium JTX H4 HID Hi and Low kit.
That's 55W HID Low Beam and 55W HID High Beam - Both beams in HID.
These lights are fabulous for seeing the edge of the road and ideal for city driving, bush tracks and country roads.
The size is 5 3/4" (143mm) round and they suit all 5 3/4" applications.. The only other sizes out there are 7" and 4.5" so if you go and have a measure it will be pretty obvious to you which size you need. Note there are some 146mm lights out there that don't fit some 143mm retaining rings and so we made sure these were the smaller size of the 2.
They are a direct replacement of your normal 5 3/4" round sealed or semi sealed headlights.
Fitting is dead easy. Remove the outer metal retainer (3 screws) and the light falls forward into your hands. Just unplug the old and plug in the new. Re-position the light and screw in the retainer and you are done. There is no need to remove the grill or headlight surrounds. The HID comes with a wiring harness that simply plugs into one of your headlight sockets. You also need to connect the red wire with fuse to the +ve terminal on the battery. And each ballast has a black wire that you need to ground to an earth and that's all there is to it.
These are excellent all rounder lights. The reflector is made of glass finish sheet metal and is shaped to project light as far forward yet as wide as possible in like a kidney bean shape so as to light up the left of the road and not shine in the eyes of oncoming drivers. The curved glass lens is rippled vertically so as to disperse light sideways. The ripples that would normally shoot light to the right are also tilted downwards so as to not project light into the eyes of oncoming drivers. It's because of this they are suited to our Australian Right Hand Drive vehicles and they are E rated and DOT approved and legal.
In this kit, you get
You don't need anything else - it is totally complete, easy to fit and ready for insane super bright light
The globes are exclusive to us - we identified where the normal H4 HID globes were failing and addressed these with the factory. The following improvements were made:
Like everything JTX these are the very best -
The inside of the ballast is filled with a resin so if any water did manage to get in, it can't do any harm .
HID lights work by passing electricity through xenon gas. There is no fragile element. To blow a globe you have to physically break it.
When the globes switch between hi and lo the core of the globe moves in and out. The globe stays on all the time so there is no heating up or loss of light between beams. There is a light shield that stops light hitting the bottom of the reflector in low beam. When the core shifts to high beam position, not only does the bright spot move into the "focal point" of the light but it also shines through a slot in the shield that allows light to hit the bottom of the reflector that then sends light upwards. Because nothing us turning on or off there is no warm up periods.
Here's how they wire up ... The wire harness has a red wire with a fuse - that goes to the +ve on the battery. It has a 3 pin plug that plugs into one of your headlight sockets. That's how it knows when to turn lights on/off and go between hi and low beams. All your old wires do is tell controller in the loom what to do so it is no load at all and your old wires do not need upgrading. Each ballast has an earth wire that needs earthing and that's all there is to it. The HID globes just plug into the harness and only go one way. So literally anyone can do this.
We have had such a good run with the quality of our HID kits we are now extending our warranties to 2 years. We can see from your feedback we automatically leave you when you pay that you are covered and so no need to even come up with proof of purchase. Being based here in Melbourne it's a fast easy process.
Everything I sell comes with a 12 month warranty. No need even to keep your proof of purchase. We can see from the feedback we left you that you bought our item and so you are covered by warranty and get our full after sales support. So why buy from me rather than Hong Kong or others ?? Well I am in Melbourne and I stand by my warranty. I have many years of sourcing the best components and now dealing with factories directly to get them to make improvements that I deem are warranted based upon 10's of thousands of sales. I have done the hard yards. Remember, a cheap kit is not cheap once you throw it out. I see it all the time.
My warranty covers you for replacement parts for 12 months. It covers non functioning ballasts, globes and wiring kits. Together we will go through a few simple steps to work out if you have a globe or ballast or wiring problem and then the part is sent to you.
I stock these kits and they are ready to post straight away. There is an express post option when you pay.