Sonic Electronix Ebay - JBL SUBBP12AM + Free NVX Sound Dampening Kit
JBL SUBBP12AM + Free NVX Sound Dampening Kit
450W Max Powered 12" Loaded Subwoofer Ported Enclosure System
JBL SUBBP12AM, SDRF20: alternate picture
JBL SUBBP12AM, SDRF20: alternate picture
JBL SUBBP12AM, SDRF20: alternate picture
JBL SUBBP12AM, SDRF20: alternate picture
JBL SUBBP12AM, SDRF20: alternate picture
JBL SUBBP12AM, SDRF20: alternate picture
JBL SUBBP12AM, SDRF20: alternate picture
JBL SUBBP12AM, SDRF20: alternate picture
JBL SUBBP12AM, SDRF20: alternate picture
JBL SUBBP12AM, SDRF20: alternate picture
JBL SUBBP12AM, SDRF20: alternate picture
JBL SUBBP12AM, SDRF20: alternate picture
0
1
2
3
4
5
6
7
8
9
10
11
JBL SUBBP12AM + Free NVX Sound Dampening Kit

JBL SUBBP12AM

450W Max Powered 12" Loaded Subwoofer Ported Enclosure System
Quantity: 1

Subwoofer Specification:

  • 12" GT Series subwoofer
  • Power Handling:
    • Peak: 450 watts
    • RMS: 150 watts
  • Subwoofer material: Polypropylene
  • Woofer surround type: Butyl Rubber
  • Oversized, stacked magnets to increase magnetic flux
  • Frequency response: 35Hz – 120Hz

Amplifier Specifications:

  • GT Series Mono block Car Amplifier counter sunk into back panel of enclosure
    • RMS Power Rating: 150 watts
    • Max power output: 450 watts x 1 chan.
  • Wired 16-1/2' remote bass level control included
  • LED power (green) and protect (red) indicators
  • Variable Bass Boost (0 to +12 dB bass boost at 45 Hz)
  • Auto turn-on
  • Nickel-plated RCA level inputs
  • Screw terminals for power, ground, and remote turn-on
  • Input sensitivity:
    • Low level: 50mV-4V
    • High level: 0.4V-16V
  • Variable low-pass filter (40-200 Hz, 24 dB/octave)
  • Subsonic filter (24 dB at 15 Hz)
  • Phase Shift: 0-180°
  • Damping factor: 200
  • Frequency response: 35-120 Hz
  • Eight gauge power and ground wiring is required for installation. Contact us for information regarding a discount on select amplifier kits from our website when purchased together with this amplifier.

Enclosure Specifications:

  • 12" Single Ported Subwoofer Enclosure
  • Round Slipstream port
  • Finish Material: Carpet
  • Dimensions: 12"D x 22-1/2"W x 14-5/8"H
  • Authorized Internet Dealer
  • 1-year Manufacturer's Warranty

NVX SDRF20

Five Sheets of 18" x 32" (20 sq. ft.) Tri-Layer Sound Damping Material (Sound Deadening) Adhesive Black Foam Rubber
Quantity: 1

Product Details:

  • NVX SDRF20
  • Five Sheets of 18" x 32" (20 sq. ft.) Tri-Layer Sound Damping Adhesive Black Foam Rubber
  • Tri Layer Design: Combines 100% Butyl Rubber, aluminum Foil, and Foam
  • Total Thickness: 1/8 inch
  • Easy to install self adhesive sheets
  • Built to withstand temperatures of -40℉ to 300℉
  • Perfect for applications on the roof, firewall, floor, quarter panels, doors, and more
  • Offers flexible and lightweight construction
  • Reduce rattles and shakes in your car
  • Increase SPL as well as overall sound quality and output of your car audio system
  • Combine this kit with the NVX SDRLR1 Sound Dampening Rubber Roller for a quick and easy installation
  • Dimensions: 18"L x 32"W
  • Authorized Internet Dealer
  • 1-year Manufacturer's Warranty




How to Install Sound Damping Properly

Sound damping can be a very beneficial accessory to reduce noise and vibration. To take full advantage of this soundproofing, read these instructions carefully and follow them till the end. It’s important to familiarize yourself with all the details to install the sound damping correctly. Incorrect installation will result in less than desirable results.

Step #1

The first step is to decide which location in your car you want to insulate. These locations include the floorboards, roof, door panels, trunk or firewall. We recommend soundproofing all metal surfaces for maximum sound deadening performance. Next, refer to your vehicle’s service manual for information on how to dismantle the trimming panels. Be careful when removing the panels to avoid breaking the fixing clips.

Step #2

Once the trimming is dismantled, remove the remainder of the factory insulation if it is damaged. If it is still intact, there is no need to permanently remove it. Next, you need to properly clean, dry and degrease the prospective surface. Sound deadening won't adhere properly if applied to a wet or dirty surface. Use a metal surface cleaner or degreaser along with a dry, clean rag. Make sure to use gloves and apply the degreaser in a well-ventilated space.

Step #3

For this step, measure the prospective surface you are going to treat. To make things easier, make a template of the appropriate size on a large sheet of paper and then transfer it to the damping material. That will make it easier to install it more accurately and avoid wasting material. Use a utility knife to cut the desired shape and size. Be careful and use gloves to protect your hands.

Step #4

Place a sheet of sound damping to the surface without removing the protective film. If it covers the surface properly, you are ready to install it. Gradually remove the protective paper film as you apply it to the surface for better adhesion. Once on the surface, press it down firmly until it is set in place. Flatten it with your hands to avoid unnecessary air bubbles. Use a rolling tool like the NVX SDRLR1 to press the mat down to the metal surface. Go across the entire surface with the roller to ensure that the sheet is installed properly.

Step #5

Once all sound deadening is in place, simply reinstall all trim pieces and carpet back to its original placement. Now you are ready to enjoy higher sound quality with fewer vibrations.

International customers are responsible for any and all customs, import duties, brokerage fees, and taxes. They are not included in the item price or stated shipping charges.

Additional shipping fees are required for locations including, but not limited to: PO Boxes, APO/FPO locations, Alaska, Hawaii, Puerto Rico, Guam, Canada and other countries outside the USA.

Product Summary
Manufacturer:
JBL
Model number:
SUBBP12AM, SDRF20
Weight:
57.00 lbs
Internal SKU:
subbp12am_sdrf20
Internal Product ID:
183657
© 2000–2021 Sonic Electronix, Inc. - 10645 Freeport Drive, Louisville, KY 40258 USA
All manufacturer names, model numbers, pictures and product descriptions are for the sole use of describing the product(s) for sale.
All trademarks and trade names are the property of their respective trademark holders.
Prices, specifications, and images are subject to change without notice.