AFTERMARKET REMOTE READY FOR PROGRAMMING 

Compatible for use with following models Plus other models:

SUITABLE for Kia Rio JB 08/2005 - 2011

Please note: This WILL NOT work if your original remote looks different  - Your existing remote MUST look like one above we have crossed out

Brand New

1 x Complete aftermarket Remote ready for programming ( will not look like the original remote )

Programming instructions listed here they will not be sent with remote

Before buying please make sure you can get car into programming mode - hazard lights will flash approx 20 times

Tip for programming

it will come down to timing it must be done quickly
if you have no working remote you must disconnect battery for 30 seconds than reconnect (just place terminal back on) and quickly jump back in the car to start programming procedure - please leave driver’s door open
Now when we do it we dont even count how many times we cycle key to on/off just keep doing this as quick as possible until hazard lights start flash
once hazard lights start flashing car is now in programming mode for you

After the 20 flash of the indicators, press the button once on each transmitter. The hazards light will flash once for each remote to confirm the remote has been added into the car.

7.    Once finished, turn the ignition key to the ON position then back to OFF to save the transmitter information and exit from the programming mode

Procedure 1 - if you have a existing working remote

we have attached video link if your having issues programming remote https://youtu.be/RezKVdPmM9M 

When entering the transmitter programming mode, all transmitters (Maximum of three) required to operate the system must be programmed at the same time. As all remotes are deleted.

With at least one current working remote:

1.    Remove the key from ignition and ensure a door is open.

2.    Lock the doors using the transmitter.

3.    Unlock the doors using the transmitter.

4.    Within 20 sec of unlocking, insert the key into the ignition switch, turn the ignition key from OFF to ON at least 20 times (landcruiser 26 times ), leaving the key in the OFF position after the 20 turn. Taking longer than 20 sec will not allow programming mode entry.

5.    The vehicle's indicators will flash 20 times to indicate successful entry.

6.    After the 20 flash of the indicators, press the button once on each transmitter. The hazards light will flash once for each remote to confirm the remote has been added into the car.

7.    Once finished, turn the ignition key to the ON position then back to OFF to save the transmitter information and exit from the programming mode

If no functional remotes are available:

1.    Ensure a door is open.

2.    Disconnect the negative (-) battery cable, wait minimum 5 sec, then reconnect. If the alarm begins to sound, complete the MANUAL OVERRIDE procedure.

3.    Within 20 sec of reconnecting the battery cable, insert the key into ignition then turn the key from OFF to ON at least 20 times, leaving the key in the OFF position after the 20 turn. Taking longer than 20 sec will not allow programming mode entry.

4.    The vehicle's indicators will flash 20 times to indicate successful entry.

5.    After the 20 flash of the indicators, press the button once on each transmitter. The hazards light will flash once for each remote to confirm the remote has been added into the car.

6.    Once finished, turn the ignition key to the ON position then back to OFF to save the transmitter information and exit from the programming mode.

 PROCEDURE 2 - With no working remotes

https://www.youtube.com/watch?v=QDav5i-N89o

Manual override

If the alarm system is armed but the wireless door lock transmitter is lost or inoperable, the alarm may be manually overriden.

During this procedure the alarm will sound. Ignore this and continue with the procedure.

1.    Unlock the driver's door using the ignition key.

2.    Using the ignition key, quickly turn the ignition switch from ACC to ON position 10 times. Leave the ignition OFF after the 10 turn and wait for the horn to stop sounding. If the system fails to override after horn stops, re-cycle the ignition 10 times then wait for the horn to stop

ITEMS ARE POSTED FROM QLD

PLEASE ALLOW 7 TO 14 BUSINESS DAYS WITH AUSTRALIA POST

WE SHIP WITHIN 2 BUSINESS DAYS