Makes oil changes even easier and faster:
-Locks in so it can't flop around while pouring!
-Vented for max flow rate - dump that oil in as fast as you can!
-Anti-splashback design!
-High strength neodymium magnet integrated for storage on any steel surface with no mess!
-Lip holds oil jug to allow it to sit and fully drain after pouring!
"Fit perfect"
"Guys at the shop loved it. The fact that it is magnetic was the driving factor for the purchase. Nothing like wind blowing over your [standard plain jane] funnel as 6 qts of oil are being poured"
"It worked great for the ___ I used it on"
"The air vent straw works great"
Locks right into the oil cap opening in your valve cover, fits Ford/Mazda vehicles with o-ringed quarter turn cap. (Test fit on a 2008 Mazda6 2.3L)
Based on a Gates #31295 oil fill cap, you can search and verify fitment here:
https://www.partsplus.com/catalog-2/itemdetail/gates/31295
Fits over 539 vehicles, this is a limited interchange from Gates:
FORD | BRONCO SPORT | 2021 |
FORD | C-MAX | 2013-2018 |
FORD | ECOSPORT | 2004-2021 |
FORD | EDGE | 2012-2021 |
FORD | ESCAPE | 2004-2021 |
FORD | EXPLORER | 2012-2021 |
FORD | F-150 | 2018-2020 |
FORD | FIESTA | 2011-2019 |
FORD | FOCUS | 2003-2018 |
FORD | FUSION | 2006-2020 |
FORD | IKON | 2011-2015 |
FORD | LOBO | 2020 |
FORD | MUSTANG | 2015-2021 |
FORD | POLICE INTERCEPTOR UTILITY | 2020-2021 |
FORD | POLICE RESPONDER HYBRID | 2019-2020 |
FORD | RANGER | 2004-2011 |
FORD | SPECIAL SERVICE POLICE SEDAN | 2014-2018 |
FORD | SSV PLUG-IN HYBRID | 2019-2020 |
FORD | TAURUS | 2013-2017 |
FORD | TRANSIT CONNECT | 2010-2021 |
LINCOLN | MKC | 2015-2019 |
LINCOLN | MKT | 2014-2016 |
LINCOLN | MKZ | 2011-2020 |
MAZDA | 3 | 2004-2021 |
MAZDA | 5 | 2006-2017 |
MAZDA | 6 | 2004-2021 |
MAZDA | B2300 | 2004-2009 |
MAZDA | CX-3 | 2016-2021 |
MAZDA | CX-30 | 2020 |
MAZDA | CX-5 | 2013-2021 |
MAZDA | CX-7 | 2009-2012 |
MAZDA | CX-9 | 2016-2021 |
MAZDA | MX-5 MIATA | 2006-2021 |
MAZDA | RX-8 | 2009-2010 |
MAZDA | TRIBUTE | 2005-2011 |
MERCURY | MARINER | 2006-2011 |
MERCURY | MILAN | 2006-2011 |
This funnel is awesome. Designed and 3d printed in Ohio, of PLA plastic. Color may vary depending on material availability- message me if this is important to you.
**Note: Printed from thermoplastic, so avoid high temperatures. A warm engine is fine, but if the engine is hot we recommend allowing it to cool enough that you can touch it (around 115 deg F).